ROBUS RRB14CCT3E-01 ORB 14W LED Surface Mount Instruction Manual
- June 8, 2024
- ROBUS
Table of Contents
ROBUS RRB14CCT3E-01 ORB 14W LED Surface Mount
FEATURES
DIMENSION
INSTALLATION
PLEASE READ INSTRUCTION BEFORE COMMENCING INSTALLATION AND RETAIN FOR FUTURE
REFERENCES.
Electrical products can cause death or injury, or damage to property. If in
any doubt about the installation or use of this product, consult a competent
electrician
Note: Product technical information and specification may change over
time without prior notification. For the latest technical information please
visit our web site www.robus.com or
robusdirect.com
0°C < Ta < +35°C, 220V – 240V ~ 50/60Hz, Class II, IP65, Battery Warranty: 2
Years Luminaire is non-dimmable Suitable for mounting on a normally flammable
surface.
Installation
-
Ensure mains supply is switched off before commencing work.
-
Ensure there is at least 100mm of free space around the luminaire location.
-
Remove diffuser from base of the fitting.
-
Drill cable entry and mounting holes in the base.
-
Mark fixing hole positions on wall, check location of buried cables, pipes or other building services before drilling.
-
Feed supply cables through cable entry hole and attach base to surface of wall.
-
Write installation date on battery and connect battery.
-
Connect wires from unswitched supply to terminals:
brown to PL, Blue to N. For fitting always on, link terminal SL to terminal PL. For fitting controlled by switch, connect switched live wire to terminal SL and permanent live to PL.
Note: if SL terminal not connected, fitting works as non-maintained. -
There is an additional terminal, that can be used for earth connection.
-
Move switch on top of the driver to select colour temperature: 3000K, 4000K or 6500K.
-
Refit trim/ diffuser to base.
Attention: In order to protect the battery life, please disconnect the battery if the power supply shut off over 3 days.
WARNING: DO NOT CHANGE CCT WHEN THE FITTING IS ON!!Switch on supply:
The green led should come on indicating correct battery charge status, all
LEDs will come on. When supply to the switched live PL is lost, battery will
operate fitting in emergency mode.
Accessory
- RRBTRIMP-01: ORB Trim Plain White
- RRBTRIMP-04: ORB Trim Plain Black
- RRBTRIMP-24: ORB Trim Plain Grey
- RRBSCREW: ORB Anti Tamper Screws
- RRBTRIMEY-01: ORB Trim Eyelid White
- RRBTRIMEY-04: ORB Trim Eyelid Black
- RRBTRIMEY-24: ORB Trim Eyelid Grey
Information for the Product user
-
Please note the requirement to dispose of Waste Electrical & Electronic Equipment separately from household waste
(WEEE marked with crossed out wheelie bin symbol). -
Please consider your role in contributing to re-use and recycling by returning this product at end of life to a collection centre for waste electrical equipment or a Civic Amenity site, or to a retail outlet from which you are purchasing a replacement.
-
This equipment may contain substances that are hazardous to health and the environment if disposed of carelessly. It is important that it is separated from normal household waste and recycled in the WEEE chain
-
The “crossed out wheelie bin symbol” on a product indicates this equipment must not be disposed of in normal household waste, but should be disposed of according to local WEEE regulations
The Installation must be carried out by a qualified electrician
Installation and Maintenance Record
Installer
Installation: Type
Installation test duration & Date
L.E.D lighting & Electrical Distribution Group UC
IRE: Nangor Road, Dublin 12, D12 E7VP, Ireland
UK: Bracknell Enterprise & Innovation Hub, Ocean House, 12th Floor, The
Ring, Bracknell, Berkshire RG12 1AX, UK
Tel: +353 1 7099000
Fax: +353 1 7099060
Email: info@robus.com
Website: www.robus.com