VIMAR 03993 Magnetic Relay Instructions
- June 8, 2024
- VIMAR
Table of Contents
VIMAR 03993 Magnetic Relay
Magnetic Quid relay module with sequential ON/OFF pulses, 1 input for NO push button, 2 10A sequential relay outputs, 220-240 V~ 50/60 Hz power supply, installation in junction boxes or connector block boxes.
The device, which can be installed in connector block boxes or inside the junction boxes declared as suitable for electrical devices that dissipate energy, controls two loads (ON/OFF) in sequence following a signal received from a push button.
CHARACTERISTICS
- Rated supply voltage: 220 – 240 V~ 50/60 Hz.
- Control via NO push buttons.
- Max. 1 switching per second.
- It should be used in dry, dust-free places at a temperature of between 0 °C and +35 °C.
- Dissipated power: 1 W with load ON and max. current 10 A 0 W and no absorption with load OFF
Switching sequence
The two loads are controlled as per the sequence illustrated in the table:
| PUSH BUTTON | LOAD 1 (L1) | LOAD 2 (L2) |
|---|---|---|
| – | OFF | OFF |
| 1st switching | ON | OFF |
| 2nd switching | OFF | ON |
| 3rd switching | ON | ON |
CONTROLLABLE LOADS
- Relay outputs (220- 240 V~ controllable loads):
- rated load in AC1: 10 A (6,000 cycles);
- rated load in AC15: 2.2 A (5,000 cycles);
- resistive load s : 10 A (20,000 cycles);
- incandescent lamps : 3 A (20,000 cycles);
- fluorescent lamps : 100 W (20,000 cycles);
- energy saving lamps : 100 W (20,000 cycles);
- LED lamps : 100 W (20,000 cycles);
- electronic transformers : 2 A (20,000 cycles);
- power supply units for LED strips: 200 W (20,000 cycles).
INSTALLATION RULES
- Installation must be carried out by qualified persons in compliance with the current regulations regarding the installation of electrical equipment in the country where the products are installed.
- The power supply circuit (L-N) must be protected against overloads by installing a device, fuse or automatic 1-way switch, with a rated current not exceeding 10 A.
- Since this is a retrofit device, art. 03993 must always be installed in protected boxes.
REMOTE CONTROL RECEPTION
Quid can be remote controlled using the following devices:
- DueFili+ video door entry system: Video Door App + art. 40507 + art. 69RH or 69PH (programmed for 2 s timed actuation) The DueFili+ system is designed to configure a timed actuation (relay art. 69RH or 69PH) and control it from video door entry indoor stations. If the indoor station is connected (art. 40507) actuation can be remote controlled via the Video Door App.
- IP video door entry system: Video Door App + art. 40607 + art. 40636 (programmed for 2 s timed actuation) The IP video door entry system is designed to configure a timed actuation (relay art.40636) and control it from video door entry indoor stations. If the indoor station is connected (art. 40507) actuation can be remote controlled via the Video Door App.
- GSM thermostat 01913: the device is fitted with a programmable output to which an auxiliary supporting relay needs to be connected (a common one-position stable relay with a 230V coil is sufficient). Actuation is then controlled via the By-Phone App or the By-Clima App (or directly via SMS text message).
REGULATORY COMPLIANCE
LV Directive. EMC directive. EN 60669-2-1 standard. REACH (EU) Regulation no. 1907/2006 – Art.33. The product may contain traces of lead.
WEEE – User information
The crossed bin symbol on the appliance or on its packaging indicates that the
product at the end of its life must be collected separately from other waste.
The user must therefore hand the equipment at the end of its life cycle over
to the appropriate municipal centres for the differentiated collection of
electrical and electronic waste. As an alternative to independent management,
you can deliver the equipment you want to dispose of free of charge to the
distributor when purchasing a new appliance of an equivalent type. You can
also deliver electronic products to be disposed of that are smaller than 25 cm
for free, with no obligation to purchase, to electronics distributors with a
sales area of at least 400 m2. Proper sorted waste collection for subsequent
recycling, processing and environmentally conscious disposal of the old
equipment helps to prevent any possible negative impact on the environment and
human health while promoting the practice of reusing and/or recycling
materials used in manufacture.
Viale Vicenza, 14 36063 Marostica VI – Italy www.vimar.com
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>