VIMAR K40960, K40965 WiFi Video Doorbell User Guide

K40960, K40965 WiFi Video Doorbell
User Guide

K40960 – K40965
Campanello video Wi-Fi
Wi-Fi video doorbell

“Smart” video door entry outdoor station for calling to connected apps, with the possibility to respond, manage locks and actuators, store audios and videos on request or following specific events.

Package contents

| Wi-Fi video doorbell complete with rear bracket
---|---
| Power supply unit (multi-plug or DIN)
| 2 3-terminal terminals (installed)
| 8GB Sd-card (installed)
| 2 Mounting screws
| 2 Wall plugs
| Anti-vandal screw key
| Reset flash drive
| Sheet of nameplate labels
| Sheet of protective labels
| Instructions sheet

External details

Bottom side view

1. Video sensor

2. Bottom – Fixing bracket

3. Infrared LED

4. Brightness sensor

5. Microphone

6. Call button

7. State LED

8. Speaker

9. Anti-vandal screw

10.  Terminal block

11. NO-NC jumper for relay

12. Side anchoring points

13. Upper anchoring points
    Internal details

14. Anti-tamper button

15. Opening for reset

16. Slot for sd-card

17. Wiring connector

18. Label with QR code

Wiring diagram

State LED

Technical data

• DC input: 24V (use the power supply unit supplied in the kit or the rectifier 40962)
• CMOS sensor 1/3” 4MPx
• Max. video resolution: 2K (2560 x 1440) pixel
• H.264 video compression
• Digital WDR (wide dynamic image regulation)
• Dimensions: 52(l) x 133(h) x 24.5(p) mm
• To work correctly there must be a stable connections to a Wi-Fi 2.4 GHz network with DHCP server and access to the Internet
• the smart “Wi-Fi video doorbell” device must be placed at a distance from the router or Wi-Fi network extender that guarantees a “good” or “medium” signal level,  according to what indicated in the VIEW Door app
• Maximum distance between the Wi-Fi video doorbell and any additional ringtone: 100 m
• Wi-Fi frequency range: 2412-2472 MHz
• Wi-Fi transmitted power: < 100 mW (20 dBm)
• RF frequency range: 433.92 MHz
• RF transmitted power: < 10 mW (10dBm)
• Protection rating: IP54
• Lock: max 12V – 1.1A (maintenance current duration can be set in the app; maintenance current equal to 200mA)
• Relay: max 12V – 2A (relay activation time can be set in the app, from 0.5s to 10s, in 0.5s steps)
  Power supply unit: Depending on the version, to power the device, the Kit includes a multi-plug power supply unit or a power supply unit for DIN rail.

Installation

1. Using the key in the package, unscrew the anti-vandal screw on the bottom of the device (9).

2. Using a screwdriver, delicately lever along the edge of the bracket, near the side anchoring points (12): in this way, the bracket (2) is released from the Wi-Fi video  oorbell body.

3.  Wire the cables to the terminals, taking care to comply with the connection order shown in point (17).

4. Screw the bracket to the wall, fixing firstly the upper hole and checking the correct vertical position, then finally the bottom hole. To correctly position the Wi-Fi video  doorbell, refer to the following figure at the bottom.

5. To store photos and videos taken with the device, check that the SD-card is inserted in the slot indicated in point (16).
   Note: if necessary, the sd-card can be inserted in the slot from the side of the connectors with the connectors facing the front of the Wi-Fi video doorbell.

6. Insert the terminal block in the related male connector and power up the device: it is now possible to connect it to the VIEW Door app.
   Close the Wi-Fi video doorbell and fix the closing screw only after having correctly connected the doorbell to the app.

App: Connection

1. To be connected to the VIEW Door app, the device requires a MyVimar account. If the account is not available, create one at the link:
   https://www.vimar.com/en/int/user/login (The account can be created both on the web and using the app).

2. During the device configuration process the device will signal the state of the configuration through the coloured state LEDs and through voice messages (only in  English). The voice messages are considered a support for configuration.

3. On initial switch-on:
   – you will hear the voice message: “Please use your mobile for Wi-Fi configuration” – the state LED will be static blue (s7)

4. Check that the mobile phone is connected to the Wi-Fi network to which the device has to be connected.

5. pen the App: tap on the login page and then on the Vimar icon at the bottom to enter the MyVimar account.
   The user manual, which can be downloaded from the website www.vimar.com, gives the complete configuration procedure.

Opening

Connecting the removable terminal block

Surface mounting

SD Card

Closing

Recommended height, unless different regulations are specified.

Multi-plug power supply unit technical data

Road, Longhua  District, Shenzhen, Guangdong, P.R. China
Model| FJ-SW2401000N
Input voltage| 100-240 V
Input frequency| 50/60 Hz
Output voltage| 24.0 Vd.c.
Output current| 1.0 A
Output power| 24.0 W
Average performance in active mode| 89.10%
Low-load performance (10%)| 76.30%
No-load power| 0.09 W
Regulatory Compliance| ErP Directive
(EU) Regulation for external power supply units no. 2019/1782.

Regulatory compliance.
RED directive. RoHS directive.
Standards EN 301 489-3, EN 301 489-17, EN 300 328, EN 300 220-2, EN 55032, EN 55035, EN IEC 61000-3-2, EN 61000-3-3, EN 62368-1, EN IEC 62311, EN IEC 63000.
REACH (EU) Regulation no. 1907/2006 – art.33. The product may contain traces of lead.
Vimar SpA declares that the radio equipment complies with Directive 2014/53/EU. The full text of the EU declaration of conformity is on the product sheet available at the following Internet address: www.vimar.com.
Installation should be carried out by qualified personnel in compliance with the current regulations regarding the installation of electrical equipment in the country where the  products are installed.

WEEE – Information for users. If the crossed-out bin symbol appears on the equipment or packaging, this means the product must not be included with other general waste at the end of its working life. The user must take the worn product to a sorted waste center, or return it to the retailer when purchasing a new one. Products for disposal can be consigned free of charge (without any new purchase obligation) to retailers with a sales area of at least 400 m 2 , if they measure less than 25 cm. An efficient sorted waste collection for the environmentally friendly disposal of the used device, or its subsequent recycling, helps avoid the potential negative effects on the environment and people’s health, and encourages the re-use and/or recycling of the construction materials.

Information notes
The product K40960 – K40965 Doorbell (Product) is a “smart” video door entry system and must therefore be used in compliance with the methods and for the purposes  provided for in these instructions. Vimar shall not be liable in any manner whatsoever for other uses or for uses which do not comply with the laws and regulations in force.
For this purpose, if the device is used in any method or for any purpose other than its intended use, the user shall comply with the provisions of Regulation (EU) 2016/679 on the protection of personal data.

For further information see www.vimar.com website
49401791A0 00 2206
Viale Vicenza, 14
36063 Marostica VI – Italy
www.vimar.com

References

• Canale Fai da te
• Accedi a MyVIMAR - Vimar energia positiva
• Home automation, electrical equipment, smart home - Vimar energia positiva
• Accedi a MyVIMAR

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>