VIMAR 46241.036A Outdoor Full-HD PT Wi-Fi Camera User Guide
- June 8, 2024
- VIMAR
Table of Contents
VIMAR 46241.036A Outdoor Full-HD PT Wi-Fi Camera
Package content
- Camera
- Power supply
- Bracket
- Sheet metal support
- Screws
- Quick Guide
- Pin
Characteristics
Installation
Positioning
- a – Ceiling type
- Take the sheet metal support apart from bracket.
- Fix the bracket on the ceiling with screws.
- Rotate the camera to snap into bracket.
- b – Wall mounting type
- Assemble the bracket and the sheet metal support 2 .
- Fix the sheet metal support on the wall with screws 3 .
- Rotate the camera to snap into backet 4 .
Configuration
Power up the camera
- Connect the camera cable to the power supply.
- Wait for the LED to status flashes, you will hear spoken feedback (“Camera ON “and then“ Camera setup ”).
Install the App on the smartphone
Download and install the Vimar “VIEW Product” App on your smartphone by searching for it directly in the App Reference store.
First access
-
a- If you already have a account for My VIMAR.
Open the App and log in with their credentials. -
b- Otherwise create a new account by tapping on the appropriate link “Create a new account “.
Carry out the following directions in the APP, enter credentials and proceed with step 4.4.
Add a camera
Follow the on-screen instructions to complete installation and connection to
your router.
To facilitate the operation, it is recommended to stay close to the
router.
Adding via QR Code: use the camera to scan the
displayed QR code on your smartphone.
Note: after turning on the camera, the status LED lights up and will
blink rapidly.
Tap “Add device + 1 then Select device 2 then Enable next step, continue
according to the instructions on the screen 3 then Set the Wi-Fi for device 4
and continue with the procedure to view the QR code.
A QR code will be displayed on the smartphone, face the phone
screen towards the camera at a distance of 15-20 cm from the lens, a beep will
sound after a few seconds, tap on “heard the beep” (refer to the pictures).
Wait for the connection to complete, after a few seconds the device will be
successfully added and give spoken feedback “Online”.
ATTENTION: in order to safeguard your data and the security
if you intend to add the same camera via another account, you need to cancel
the camera from the App where it is associated, in case of return of the
product, is recommended in addition also to format the SD card.
The camera is also compatible with the application Smart Life
For more information see the complete manuals and up-dated available in the
product sheet on the site:
https://faidate.vimar.com/it/it
Specifications
| Camera | Image sensor | 2 Megapixel CMOS |
|---|---|---|
| Effective pixels | 1920(H)*1080(V) | |
| IR distance | Night visibility up to 10 m | |
| Day/Night | Auto(ICR)/Color/ B/W | |
| Lens | 3.6 mm 100° | |
| pan/TILT limit | Pan 0-355° Tilt -10°-75° | |
| Video and Audio | Encoding | H.264/H.265 |
| Audio input/output | 1 MIC/1 SPEAKER included | |
| Live | 25 fps | |
| Network | Alarm trigger | Intelligent motion detection |
| Communication Protocol | HTTP,DHCP,DNS,TCP/IP,RTSP | |
| Wi-Fi – Wireless | 2.4 G WIFI(IEEE802.11b/g/n) | |
| Security | User authentication, Wi-Fi Password max 63 characters | |
| General | Operating temperature | -10 °C to 50 °C |
| Power supply | DC 12 V / 1 A | |
| Ingress protection | Valid only for ceiling or wall mounting) | |
| Storage | 32 GB included Protected movie recording | |
| Dimensions | Ø 76.5 x 107 mm |
Operation disclaimer for Wi-Fi cameras
The Wi-Fi camera (item 46241.036A) allows images to be viewed on the buyer’s
(hereinafter “Customer”) smartphone and / or tablet, by simply installing the
Vimar VIEW Product application.
The visualization of the images is allowed only through the presence, in the
house / building in which it is installed, of a connection to a home Wi-Fi
network with Internet access which must have the following characteristics:
- IEEE 802.11 b / g / n (2.4 GHz) standard
- Frequency range: 2412-2472 MHz
- Transmitted RF power: <100mW (20dBm)
Operating modes:
- Networks: WEP, WPA and WPA2.
- TKIP and AES encryption protocols are supported for WPA and WPA2 networks.
- Do not support “hidden” networks (hidden SSID).
To use the service The Customer must have technical equipment that allows
connection to the Internet and sign an agreement with an ISP (Internet Service
Provider); this agreement may involve related costs. Vimar remains unaffected
by the choice of technical equipment and the agreement with the ISP (Internet
Service Provider). The consumption of data through the use of the Vimar VIEW
Product App, both in the home /building and outside the Wi-Fi network that the
Customer has used for installation, remains the responsibility of the
Customer.
The interaction and correct operation remotely via the Vimar VIEW Product App,
through the Internet network of your mobile phone / data provider, with the
Wi-Fi camera installed by the Customer (art. 46241.036A) may depend on:
- a) type, brand and model of the smartphone or tablet;
- b) quality of the Wi-Fi signal;
- c) type of the home internet access contract;
- d) type of data contract on the smartphone and tablet.
The camera (item 46241.036A) supports connection via P2P technology, it is
therefore necessary to check that your ISP (Internet Service Provider) does
not block it.
Vimar is exempt from any liability for any malfunctions due to non-compliance
with the minimum technical specifications necessary for the operation of the
product which are indicated above. To resolve any problems, refer to the
complete manual and the “Questions and answers” section on the product page at
the following Internet address: faidate.vimar.com. Vimar reserves the right to
modify the characteristics of the products shown at any time and without
notice.
Conformity
RED directive. RoHS directive
Standards EN 301 489-17, EN 300 328, EN 62311, EN 62368-1, EN 55032, EN 55035,
EN 61000-3-2, EN 61000-3-3, EN IEC 63000.
REACH (EU) Regulation no. 1907/2006 – Art.33. The product may contain traces
of lead.
Vimar Spa declares that the radio equipment complies with Directive
2014/53/EU. The full text of the EU declaration of conformity, the instruction
manual and the configuration software are on the product sheet available at
the following Internet address: faidate.vimar.com
WEEE – Information for users
If the crossed-out bin symbol appears on the equipment or packaging, this means the product must not be included with other general waste at the end of its working life. The user must take the worn product to a sorted waste center, or return it to the retailer when purchasing a new one. Products for disposal can be consigned free of charge (without any new purchase obligation) to retailers with a sales area of at least 400m2, if they measure less than 25cm. An efficient sorted waste collection for the environmentally friendly disposal of the used device, or its subsequent recycling, helps avoid the potential negative effects on the environment and people’s health, and encourages the re-use and/or recycling of the construction materials.
Privacy
Privacy Policy
As required by Regulation (EU) 2016/679 on the protection of personal data,
Vimar S.p.A. guarantees that the electronic processing of data minimises the
use
of personal and other identification information, which is only processed to
the extent strictly necessary in order to achieve the purposes for which it
was collected. The personal information of the Data Subject is processed in
accordance with the product/application privacy policy available on our
website www.vimar.com in the legal section
Please remember that, pursuant to Regulation (EU) 2016/679 on the protection
of personal data, the user is the controller of processing for the data
collected during use of the products and, as such, is responsible for adopting
suitable security measures that protect the personal data recorded and stored,
and avoid its loss. Should the products monitor public areas and not just
private property, it will be necessary to display – in a visible manner – the
information about the ‘area under video surveillance’ envisaged in the privacy
policy and specified on the website of the Italian Data Protection Authority
(Guarantee).
Images may be stored for 24 hours, and for up to 72 hours in the cases
envisaged in the video surveillance measures issued by the Italian Data
Protection Authority on 8 April 2010.
In addition, the user must guarantee safe possession of and control over its
passwords and the related access codes to its web resources. The Data Subject
must provide the password for access to its system when requesting help from
the Vimar Support Centre, so that the related support can be provided.
Provision of the password represents consent for processing. Each Data Subject
is responsible for changing the password for access to its system on
completion of the work carried out by the Vimar Support Centre.’
Viale Vicenza, 14
36063 Marostica VI – Italy
www.vimar.com
References
- Canale Fai da te
- Home automation, electrical equipment, smart home - Vimar energia positiva
- Canale Fai da te
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>