LEXON LL128 Nomaday Lock Instruction Manual
- June 8, 2024
- LEXON
Table of Contents
LL128
NOMADAYLOCK
Design by Guillaume Delvigne
Instruction Manual
PRODUCT OVERVIEW
- Lock hook
- Lock body
- Light indicator
- Fingerprint reader
- USB Type-C port
FEATURES
- Sleek & compact design
- Advanced fingerprint technology
- Records up to 10 profiles
- Powerful rechargeable storage battery
- IP65 Waterproof
CHARGING
- Plug the USB cable to a USB charging source (5V output).
- Plug the end of the USB Type-C plug into the padlock USB Type-C port.
| Low battery | Green light flashes each time you touch the fin erprint reader |
|---|---|
| Charging | Steady Green |
| Fully charged | Off |
Notice: Please do not operate the fingerprint padlock when charging
PADLOCK PROGRAMMING
Factory mode
Any fingerprint can unlock the padlock.
Register Administrator & User accounts
The administrator profile must be registered first before any other profile.
Administrator confirmation is required to add new users.
Notice: Make sure to position your finger properly to avoid hiding the LED
indicator located at the top of the fingerprint reader
Set administrator account
The administrator account will be identified when registering or resetting the
user account.
Please ensure your padlock is in standby. The padlock must be locked, and the
indicator light off.
1. Press and hold your finger on the fingerprint reader for about 4 seconds.
Release your finger as soon as the light turns blue.| 2. Put the
administrator account’s finger on the fingerprint reader. Repeat 10
consecutive times with the same finger.
---|---
|
3. After successfully recording the fingerprints ten times, a long beep sound
will be heard to confirm the success of the operation.| In case of failure,
the light indicator turns red.
|
Set user accounts
1. Press and hold your finger on the fingerprint reader for about 4 seconds.
Release your finger as soon as the blue and red light starts flashing.| 2.
Put the administrator account’s finger on the fingerprint reader. Then wait
until the light turns blue.
---|---
|
3. Put the user account’s finger on the fingerprint reader. Repeat 10
consecutive times with the same finger.| 4. After successfully recording the
fingerprints ten times, a long beep sound will be heard to confirm the success
of the operation.
In case of failure, the light indicator turns red.
|
Notice: If the user accounts are full. you must reset the padlock when you want to register a new user account
Unlock
- When the padlock is in standby, put the registered fingerprint on the fingerprint reader, the blue light will turn on and the padlock will beep twice. If the fingerprint is incorrect, the light will turn red and the padlock will beep 3 times.
Reset
If you want to set new administrator account or delete accounts, please reset
the fingerprint padlock firstly, and then set new accounts.
- Press and hold your finger on the fingerprint reader for about 8 seconds. Release your finger as soon as the red light starts flashing
- Put the administrator account’s finger on the fingerprint reader. The light will turn red the padlock will emit a long beep to confirm the success of the operation.
Notice: When the resetting is successful, you can use any finger to unlock. Please remember to set administrator account firstly, then use the padlock. All the accounts’ fingerprint will delete after resetting.
Troubleshooting
| Issues | Reasons | Solutions |
|---|
The LED remains off when you press the fingerprint
panel| No battery power| Make sure to charge the fingerprint padlock
Cannot unlock| Your finger is too wet or dirty| Make sure your finger is clean
and dry. Place it on
the fingerprint reader again
Fingerprint reader not clean| Clean the fingerprint reader with a dry cloth
Any finger can unlock the padlock| No administrator account has been created
yet| Set the administrator account
SAFETY PRECAUTIONS
Read all the instructions before using the device
- The factory setting of all new Nomaday lock will allow any fingerprint to open it.
- Make sure to register an administrator for the newly installed lock. The lock cannot register normal users without an administrator.
- Please recharge the battery promptly when the lock indicates low battery power.
- Please keep your finger clean when touching the fingerprint panel.
- Do not attempt to dissemble the smart lock by yourself.
- Do not use any inappropriate tools that can cause damages or malfunction to your lock.
- Keep it far away from the flammable and explosive gas.
- Make sure the adaptor output is 5V when charging.
PRODUCT SPECIFICATIONS:
Case material. Zinc Alloy/Stainless steel
Net Weight. 84 g
Size: Lock 3,2x77x 1.4 cm/ Ring 4mm
Usage closetlluggagelhandbagldoor
Fingerprint collecting time: <0.5s
Fingerprint matching time: <1s
Fingerprint reader resolution. 9696
Unlock system: fingerprint touch
Buzzer Yes
LED indicator fingerprint touch & charging status
LED light color Red, Blue & Green
Power Supplier 5V
Battery life: up to 3000 unlock times after full charge / up to 9 months
depending on the frequency of your usage
Battery type: 3,7V lithium battery
Battery capacity:260 mAh
Working voltage: 3.3-4.2V
Charging time: 1.5h
Operating temperature: -10 – +45°C
Port USB Type-C cable
Water resistance: IP65 (Protected against splashing or sprayed water from any
angle)
EUROPEAN UNION CE DIRECTIVE
LEXON hereby declares that the device is in compliance with the essential
requirements and other relevant provisions of Directives 2014/30/EU and
2011/65/EU.
The original EU declaration of conformity may be found at: https://www.lexon-
design.com/assets/certifications-ce-nomadaylock.pdf
DISPDSAL AND RECYCLING INFORMATION
After the implementation of the European Directive 2012/19/EU in the national
legal system, the following applies electrical and electronic devices may not
be disposed of with domestic waste.
Consumers are obliged by law to return electrical and electronic device at the
end of their service lives to the public collecting points set up for this
purpose or point of sale. Details to this are defined by the national law of
the respective country. This symbol on the product, the instruction manual or
the package indicates that a product is subject to these regulations. By
recycling reusing the materials or other forms of utilizing old devices, you
are making an important contribution to protecting our environment.
USA-FCC STATEMENT
This device complies with part 15 of the FCC Rules.
Operation is subject to the following two conditions
(1) This device may not cause harmful interference. and
(2) this device must accept any interference received, including interference
that may cause undesired operation.
Notice
Any changes or modifications not expressly approved by the party responsible
for compliance could void your authority to operate the equipment,
NOTE This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference in a residential installation.
This equipment generates, uses and can radiate radio frequency energy and, if
not installed and used in accordance with the instructions, may cause harmful
interference to radio communica tions. However, there is no guarantee that
interference will not Occur in a particular installation, If this equipment
does cause harmful interference to radio or television reception which can be
determined by turning the equipment off and on the user is encouraged to try
to correct the interference by one or more of the following measures.
– Reorient or relocate the receiving antenna.
– Increase the separation between the equipment and receiver,
– Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
– Consult the dealer or an experienced radio/ TV technician for help.
RF exposure statements
This equipment complies with FCC radiation exposure requirement set forth for
an uncontrolled environment.End users must follow the specific operating
instructions for satisfying RF exposure compliance.
CANADA -INDUSTRY CANADA (IC) STATEMENT
This device complies with Industry Canada license-exempt RSSs.
Operation is subject to the following two conditions:
- This device may not cause interference and
- This device must accept any interference, including interference that may
cause undesired operation of the device.
This Class B digital apparatus complies with Canadian ICES-003.
RF exposure statements
This device complies with the ISED RSS-102 RF exposure requirement set forth for an uncontrolled environment and are safe for intended operation as described in this manual.
CAUTION
Risk of explosive if battery is replaced by an incorrect type.
Dispose of used batteries according to the instructions.
IP65 – Protected against low pressure water jets from any direction, as well as condensation and water spray.
All brands or
product names are or may be trademarks or their respective owners.
Pictures and specifications are not contractual. Assembled in China.
Iexon-design.com
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>