cangaroo BL11872 Baby Crib User Manual

June 8, 2024
CANGAROO

cangaroo BL11872 Baby Crib

BL11872 Baby Crib

IMPORTANT! READ CAREFULLY AND KEEP FOR FUTURE REFERENCE

WARNING!

  • Do not use this product without reading the instructions for use first.
  • The product is intended for children aged between 0 and 12 months, weighted up to 11 kg.
  • Stop using the product as soon as the child can sit or kneel or pull itself up.
  • Placing additional items in the product may cause suffocation.
  • Do not place the product close to another product, which could present a danger of suffocation or strangulation, e.g. strings, blind/curtain cords, etc.
  • Do not use more than one mattress in the product.
  • Only use the mattress sold with this crib, do not add a second mattress on this one, suffocation hazards!
  • The product should be placed on a horizontal floor.
  • The young children should not be allowed to play unsupervised in the vicinity of the crib.
  • The crib should be locked in the fixed position when the child is left unattended.
  • All assembly fittings should always be tightened properly and that care should be taken that no screws are loose, because a child could trap parts of the body or clothing (e.g. strings, necklaces, ribbons for babies’ dummies, etc.) which would pose a risk of strangulation. Perform routine checks to make sure there are no loose, damaged or missing parts.
  • The maximum internal size of the crib the mattress is intended for is 900/590 mm. The length and width shall be such that the maximum gap between the mattress and sides and ends does not exceed 2,5 cm.
  • The product shall be kept away from burning cigarettes, open fires and other sources of strong heat, such as electric bar fires and gas fires.
  • The base of the crib can be tilted up to 30° to prevent any discomfort and danger of suffocation of the child.
  • DO NOT use the crib if any parts are missing, damaged or broken. Contact MONI TRADE for replacement parts and instructional literature, if needed. DO NOT substitute parts.
  • Using the product as fixed to the adult’s bed is only permitted with beds and/or mattress with straight sides. Use of the product with round beds and/or mattress or water beds or inflatable mattress IS NOT PERMITTED!
  • ATTENTION! Do not use the “Co-sleeping function” of the crib if the height of the adult’s bed is less than 45 cm or more than 60 cm above the floor.
  • Bedside sleepers shall never be used in an inclined position. In co-sleeping function the 2 legs of the crib must always be set to the same height position.
  • Do not adjust the product or move it while the child is inside.
  • When using the product at “Co-sleeping function”, to prevent a suffocation hazard from entrapment, the bedside sleeper shall be properly secured to the adult bed using the attachment system.
  • Always use the attachment system provided with this product.
  • Check the tightness of the attachment system before each use by pulling the bedside sleeper in a direction away from adult bed.
  • If there is any gap between the bedside sleeper and adult bed DO NOT use the product.
  • Gaps should not be filled with pillows, blankets or other items.
  • WARNING – To avoid hazards from the child’s neck being caught on the top railon the side  that is next to the adult bed, the top rail must not be higher than the adult bed mattress.
  • WARNING – To avoid the risk of your child befing strangled the attachment system to the adult’s bed shall always be kept away from and out of the crib.
  • DANGER! Always completely raise the drop side when not attached to the adult’s bed!
  • Assemble, unfold and fold the product ONLY by an adult.
  • Do not allow children under 3 years of age till fully assemble the product to avoid access to small and disassembled parts.
  • Any plastic cover should be removed , destr,oyed or kept away from children to avoid suffocation.
  • Do not make any changes or improvements to the design of the crib, as this may damage the crib and risk injury to the child.

ASSEMBLY AND OPERATING INSTRUCTIONS

IMPORTANT! The diagrams and figures in this instruction are illustrative and indicative only. Follow exactly the instructions and sequence for assembling and operating with the product. Check the securing of the fixation after each operation.
Components – illustration A

After unpacking, make sure that all elements of illustration A are available: Crib basket; Crib mattress; Carry bag, Side frames (legs); Main support frame; Belts; 4 pcs bolts; 1 tool.
Assembly and operation
ATTENTION! Follow exactly the instructions and sequence for assembling and using the product, described in the text and illustrations attached to the instructions.
Figure B – Assemble the bed stand by placing t he main support frame “C” in the connecting parts (holes) of the two side frames (legs) “A” and “B” in the direction of the arrows as showed in the illustration. Each side frame is equipped with two bolts to secure the main support frame to the bed. Use a hexagon to tighten the bolts clockwise. ATTENTION ! Make sure the frame is tight and stable. This is the supporting part of the crib and ensures the safety of your child.
Assembly And Operating Instructions
Figure C – Attach the crib basket to the mounted stand by fixing the connecting part of the basket frame to the top of the two side frames “A” and “B”. The spring pin will snap into place once it is securely fastened on both sides. CAUTION ! Make sure the bolts are tight and the bin is firmly attached to the crib stand.
Assembly And Operating Instructions
Figures D, E – Lowering and lifting the drop side. Open the zipper, which is located under the padded upper rail. lift the drop side of the crib so that it detaches from the base, and attach the falling side to the bottom of the crib. Close the side panel until you hear a clicking sound and close the zipper on both sides. If you want to lift the drop side of the crib, detach it and reattach it to the base of the crib on both sides. Use the side zippers to close completely. Use the metal ring to connect the two zippers together so that they cannot open. The cot is ready to use as a separate bed.
Assembly And Operating Instructions
Assembly And Operating Instructions
Figure F – Moving the crib. To move the crib, lift the back of the bed, then move it to the desired location using the factory-fitted two-legged fixtures. The legs of the crib are equipped with a braking device (stoppers) that stop the movement of the crib and keep it firmly locked.
Assembly And Operating Instructions
Figure G – Height adjustment and antireflux function. The height can be adjusted ins positions.
To adjust the height, press the adjustment button and release it when the desired position  is reached. The base of the basket can be used with an inclination of up to 30 • to prevent discomfort and danger of suffocation of the child. The baby cot can be tilted with a difference of maximum 2 positions in height. (Example: the right foot is in a position 3 and the left is in a position 1). ATTENTION! The anti-reflux function can be applied only when the crib is used as a separate bed. The child’s head should always be on the highest side.
Assembly And Operating Instructions
Figure H – Attaching the crib to the adult’s bed. Remove the drop side by unbuttoning the zippers on both sides and securing it to the bottom of the crib. Use the two seat belts provided in the kit to secure the crib to the parent’s bed. Lock the buckles under the crib on both sides, then secure the belts around the structure of the parent’s bed, starting at the bottom and going up, and finally tightening the buckles under the bed. To secure the crib when it is next to the parent’s bed, pull the straps once more to make sure the crib is securely attached to the parent’s bed.
Assembly And Operating Instructions

INSTRUCTIONS FOR MAINTENANCE AND CLEANING

Clean the plastic or metal parts of the product with a soft cotton cloth or sponge moistened with water or a mild detergent. Do not use bleach, agressive detergents or abrasive products to clean the product. All textile parts and fabrics should be washed only by hand, following the instructions on the label. After cleaning, allow the crib to dry well before using it. Do not fold or remove the crib before it is completely dry. Do not expose the product to direct sunlight for extended periods of time and to extreme temperatures that may change color and damage exposed parts. After prolonged exposure to high temperatures, wait a few minutes before placing the child in it. Do not place objects in or on the product to avoid damaging the structure and/ or upholstery. Store the product in a clean and dry place.
Assembly And Operating Instructions

CUSTOMER SUPPORT

Manufactured for Cangaroo in PRC
Manufacturer and Importer: Moni Trade Ltd.
Address: Bulgaria, Sofia, Trebich, 1 Dolo Str.,
Phone number: 003592/936 07 90
Website:www.cangaroo-bg.com

References

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals