cangaroo P9070 Baby Cot Indiana User Manual

cangaroo P9070 Baby Cot Indiana

This product is manufactured in accordance with the requirements of the EU Directive 2001/98/EC on General Product Safety, the Consumer Protection Act, and the active versions of the European Standards: EN 716-1:2017; EN 716-2:2017.

IMPORTANT! READ CAREFULLY AND KEEP FOR FUTURE REFERENCE

WARNING

• WARNING! Be aware of the risk of open fire and other sources of strong heat such as electric bar fires, gas fires etc. in the near vicinity of the cot.
• WARNING! Do not use the cot if any part is broken, torn, or missing. Use only spare parts approved by the manufacturer.
• WARNING! Do not leave anything in the cot or place the cot close to another product, which could provide a foothold or present a danger of suffocation or strangulation, e.g., strings, blind/curtain cords etc.
• WARNING! Do not use more than one mattress in the cot.
• A cot is ready for use when the locking mechanisms are engaged. Check carefully that locking systems are fully engaged before using the folding cot.
• All assembly settings should always be tightened properly and should be checked regularly and retightened if necessary.
• The lowest position is the safest and the base should always be used in that position as soon as the baby is old enough to sit up.
• Where detachable support rails are provided to support the cot base above its lowest position, it is essential to remove these rails before the cot is used in its lowest position.
• To prevent injury from falls that when the child is able to climb out of the cot, the cot shall no longer be used for that child.
• WARNING! Only use the mattress sold with this cot, do not add a second mattress on this one, suffocation hazards!
• Accessories which are not approved by the manufacturer shall not be used. Never hang additional accessories on the cot except the musical fretboard which is provided with the cot and described in the instructions.
• Using the product as fixed to the adult’s bed is only permitted with beds and/or mattress with straight sides. Use of the product with round beds and/or mattress or water beds or inflatable mattress IS NOT PERMITTED!
• ATTENTION! Do not use the “Co-sleeping function” of the crib if the height of the adult’s bed is less than 45 cm or more than 60 cm above the floor.
• Bedside sleepers shall never be used in an inclined position. In co-sleeping function the 2 legs of the crib must always be set to the same height position.
• Do not adjust the product or move it while the child is inside.
• When using the product at “Co-sleeping function”, to prevent a suffocation hazard from entrapment, the bedside sleeper shall be properly secured to the adult bed using the attachment system.
• Always use the attachment system provided with this product.
• Check the tightness of the attachment system before each use by pulling the bedside sleeper in a direction away from adult bed.
• If there is any gap between the bedside sleeper and adult bed DO NOT use the product.
• The maximum distance between the crib and the parent’s bed should be 2 cm.
• Assemble, unfold and fold the product ONLY by an adult.
• Do not allow children under 3 years of age till fully assemble the product to avoid access to small and disassembled parts.
• Any plastic cover should be removed, destroyed or kept away from children to avoid suffocation

ASSEMBLY AND OPERATING INSTRUCTIONS

IMPORTANT! The diagrams and figures in this instruction are illustrative and indicative only.
Follow exactly the instructions and sequence for assembling and operating with the product. Check the securing of the fixation after each operation.
THE BABY COT SET INCLUDES: Folding cot; Second layer; Toy bar with 4 toys; Nursery purse; Carrying bag.
ASSEMBLY AND OPERATION: ATTENTION! Follow exactly the instructions and sequence for assembling the product as described in the text and illustrations. Never put fingers inside the corners or any other moving parts of the cot while folding and unfolding the cot.

1. UNFOLDING THE COT – Remove the cot from the bag. Loosen the self-adhesive tapes that hold the mattress. Remove the cot and set the mattress aside. Place the cot upright and separate the legs by pulling both sides of the cot in opposite directions. Unfold all four corners of the crib so that you can catch the locking mechanisms in the middle of each side. Lift the sides of the crib until they lock. Push the centre of the crib down until it is fully unfolded and locked (you will hear a clicking sound). Place the mattress in the cot with the soft side up. Attach the mattress to the base.
   
   

2. FOLDING THE COT – Remove the mattress. Pull the strap of the locking mechanism on the bottom of the cot as MAXIMUM as possible to release the lock. ATTENTION! Failure to pull the mechanism to its highest position may damage the locking of the sides. Warranty conditions do not include damage caused by improper use of the product. Find the buttons in the middle of each side. Press them and fold all sides of the crib. Take the mattress and wrap it around it. Close the package by wrapping the velcro straps around the mattress. Put the cot in the carrying case and fasten the zipper.
   

3. INSTALLING THE SECOND FLOOR LEVEL – Install the second level with its zipper and the one on the sides of the cot. Place the tops of the 4 metal tubes in the pockets at the top of the second level and connect the tubes. Place the mattress on the second level and secure it with the straps under it.
   
   
   

4. ATTACHING THE COT TO THE ADULT’S BED – Тakedown the sideway panel of the bed and lock it in the crib’s basis, using the locking button. Use the two seat belts provided in the kit to secure the baby cot to the parent’s bed. Lock the buckles under the cot on both sides, then secure the belts around the structure of the parent’s bed, starting at the bottom and going up, and finally tightening the buckles under the bed. To secure the baby cot when it is next to the parent’s bed, pull the straps once more to make sure the crib is securely attached to the parent’s bed.
   

5. INSTALLATION AND USE OF THE CRIB TOY – Connect all parts of the bar and fix it to the desired side of the playpen. ATTENTION! In order to avoid unlocking of the safety mechanism and folding of the baby cot, attach the plastic base of the music toy with the cut part out as shown in Figure 5.
   

6. ATTACHING THE NURSERY PURSE – Use the belt with tic tac button on the short side to attach the nursery purse to the baby cot as shown in Figure 6.
   

INSTRUCTIONS FOR MAINTENANCE AND CLEANING

Clean the plastic or metal parts of the product with a soft cotton cloth or sponge moistened with water. For cleaning the changing pad follow the instructions on the label. Do not use bleach, aggressive detergents, or abrasive products to clean the product. All textile parts and fabrics should be washed only by hand, following the instructions on the label (to be cleaned with a damp cloth and a mild detergent). After cleaning, allow the cot to dry well before using it. Do not fold or remove the cot before it is completely dry. Do not expose the product to direct sunlight for extended periods of time and to extreme temperatures that may change cooler and damage exposed parts. Do not place objects in or on the product to avoid damaging the structure and / or upholstery. Store the product in a clean and dry place.

CUSTOMER SUPPORT

Manufactured for Cangaroo in PRC,
Manufacturer and Importer: Moni Trade Ltd.
Address: Bulgaria, Sofia, Trebich, 1 Dolo Str.,
Phone number: 003592/936 07 90,
Website: www.cangaroo-bg.com

References

• Cangaroo - детски стоки, колички, проходилки, столчета, кошарки
• Cangaroo - детски стоки, колички, проходилки, столчета, кошарки

Read User Manual Online (PDF format)

Download This Manual (PDF format)

Download this manual  >>