KICHLER Adeena 26.75 in. 6-Light Chandelier Instruction Manual

: October 30, 2023
: KICHLER

Table of Contents

FIXTURE DIAGRAM
PARTS LIST
CAUTIONS
INSTALLATION INSTRUCTIONS
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

Adeena 26.75 in. 6-Light Chandelier
We’re here to help 866-558-5706
Hrs: M-F 9am to 5pm EST
Instruction Manual

FIXTURE DIAGRAM

PARTS LIST

[A] Body Assembly
[B] Coupler
[C] Shade Frame
[D] Canopy
[E] Strap Mounting Screw| [F] Outlet Box (not supplied)
[G] Mounting Strap
[H] Loop
[I] Open Chain Link
[J] Mounting Screw
[K] Chain| [L] Lock-up Knob
[M] Lock Washer
[N] Shade
[O] Decorative Stem Assembly
[P] Socket
---|---|---

CAUTIONS

CAUTION – RISK OF SHOCK:
Disconnect Power at the main circuit breaker panel or main fusebox before starting and during the installation.
WARNING:

This fixture is intended for installation in accordance with the National Electrical Code (NEC) and all local code specifications. If you are not familiar with code requirements, installation by a certified electrician is recommended.
Failure to adhere to these codes and instructions may result in serious injury and/or property damage and will void the warranty.

CLEANING:

Always be certain that electric current is turned off before cleaning.
Only a soft damp cloth should be used. Harsh cleaning products may damage the finish.

INSTALLATION INSTRUCTIONS

Thread the decorative stem assembly[O] into coupler[B] on the body assembly[A].
Attach one end of chain[K] to top of loop of decorative stem assembly[O] using an open chain link[I]. Attach other end of chain[K] to loop[H] using the other open chain link[I].
NOTE: To close an open chain link, place a piece of cloth (not supplied) over the open link and use a pair of pliers to gently squeeze the link closed.
Weave fixture wires through chain links no more than 3 inches apart. Pass fixture wires through loop[H] and into canopy[D].
Cut fixture wires a MINIMUM of 20 inches from the top edge of canopy.
Find the appropriate threaded holes on mounting strap[G] that align with hole distance in canopy[D]. Screw mounting screws[J] into threaded holes starting from the outlet box side.
Attach mounting strap to outlet box[F] using the strap mounting screws[E]. Mounting strap can be adjusted to suit position of fixture.
Grounding instructions: (See Illus. a or b).
a. On fixtures where mounting strap is provided with a hole and two raised dimples, wrap ground wire from outlet box around green ground screw, and thread into hole.
b. On fixtures where a cupped washer is provided, attach ground wire from outlet box under cupped washer and green ground screw, and thread into mounting strap.
If fixture is provided with ground wire, connect fixture ground wire to outlet box ground wire with wire connector after following the above steps. Never connect ground wire to black or white power supply wires.
Make wire connections. Reference chart below for correct connections and wire accordingly.
Connect Black or Red Supply Wire to:| Connect White Supply Wire to:
---|---
Black| White
Parallel cord (round & smooth)| Parallel cord (square & ridged)
Clear, Brown, Gold or Black without Tracer| Clear, Brown, Gold or Black with Tracer
Insulated wire (other than green) with copper conductor| Insulated wire (other than green) with silver conductor

*Note: When parallel wire (SPT 1 & SPT 2) are used. The neutral wire is square shaped or ridged and the other wire will be round in shape or smooth (See illus.)

Raise canopy to ceiling, carefully passing mounting screws[J] through mounting screw holes in canopy.
NOTE: Make sure wires do not get pinched between mounting plate and canopy or canopy and ceiling.
Secure canopy using lock washers[M] and lock-up knobs[L]. Tighten lock-up knobs to secure canopy to ceiling.
Carefully slip a shade frame[C] over a socket[P] until seated on socket base. Repeat for remaining shade frames.
Insert recommended bulbs (not supplied).
Carefully lower a shade[N] over a shade frame until seated on shade frame. Repeat for remaining shades.