luminii KS-XX Kendo S Dynamic White Instruction Manual
- June 8, 2024
- luminii
Table of Contents
Kendo S Dynamic White
Instruction Manual
KS-XX Kendo S Dynamic White
*LUMINII RESERVES THE RIGHTS TO CHANGE SPECIFICATION & INSTRUCTION WITHOUT NOTICE.
Kendo S – Installation Instructions Models S –
Please read all instructions prior to installation and keep for future
reference!
- PRODUCT TO BE INSTALLED BY A QUALIFIED ELECTRICIAN
- USE ONIY WITH CLASS 2 POWER UNIT
- 24 V0IS DC
- SUITABLE FOR DAMP LOCATIONS
- SURFACE MOUNT ONIY
- SUITABLE FOR INSTALLATION WITHIN THE CLOSET STORAGE SPACE
Fixed mounting clip installation
1.1 Determine the location of where the fixture[s) will be installed. Lay the
fixture[s) on the surface and make any necessary reference marks for the fixed
mounting clips (or if using the fixed 45° degree mounting clip) Moake marks 4″
from each end of the fixtures] and also every 30″ in between.
1.2lay the fixed clip onto the reference mark points and secure using the
provided hardware.
2.1: necessary make any pass through holes for wire lead/connector to the
surface, depending on the power feed option. Then snap the fixture into the
fixed mounting clip to secure in place. Diagram on the right side illustrates
the common way of connecting multiple fixtures to each other, depending on the
location of the power teed wires.
Please read all instructions prior to installation and keep for future
reference!
- PRODUCT TO BE INSTALLED BY A QUALIFIED
- USE ONIY WITH CLASS 2 POWER UNIT
- 24 V0IS DC
- SUITABLE FOR DAMP LOCATIONS
- SURFACE MOUNT ONIY ELECTRICIAN
- SUITABLE FOR INSTALLATION WITHIN THE CLOSET STORAGE SPAC
Adjustable hinge mounting clip installation
1.1 Determine the location of where the fixture[s) will be installed. lay the
fixture[s) on the surface, and make reference marks for the mounting clips.
Make marks 4″ from each end of the fixture[s) and also every 30″ in between.
1.2 Slightly loosen the 2 screws on the side on adjustable bracket lay the
bracket onto the reference mark points and secure using the provided hardware.
2.1: necessary make any pass through holes for wire lead/connector to the
surface, depending on the power feed option. Then snap the fixture into the
fixed mounting clip to secure in place. Diagram on the right side illustrates
the common way of connecting multiple fixtures to each other, depending on the
location of the power teed wires
Please read all instructions prior to installation and keep for future
reference!
- PRODUCT TO BE INSTALLED BY A QUALIFIED
- USE ONIY WITH CLASS 2 POWER UNIT
- 24 V0IS DC
- SUITABLE FOR DAMP LOCATIONS
- SURFACE MOUNT ONIY ELECTRICIAN
- SUITABLE FOR INSTALLATION WITHIN THE CLOSET STORAG
Magnetic mounting clip installation
1.1 Determine the location where the fixture[s) will be installed. Must be mode of steel or a ferrous metal Cleon the surface area thoroughly from any debris
2.1 l/ necessary make any pass through holes for wire lead/connector to the surface, depending on the power feed option. Place fixture onto the surface to secure in place. Diagram on the right side illustrates the common way o connecting multiple fixtures to each other, depending on the location of the power teed wires.
Kendo S – Installation Instructions
Models S –
Please read all instructions prior to installation and keep for future
reference!
- PRODUCT TO BE INSTALLED BY A QUALIFIED
- USE ONIY WITH CLASS 2 POWER UNIT
- 24 V0IS DC
- SUITABLE FOR DAMP LOCATIONS
- SURFACE MOUNT ONIY ELECTRICIAN
- SUITABLE FOR INSTALLATION WITHIN THE CLOSET STORAGE SPACE
Connect to Power
1.1 Follow one of the two options to connect the fixture to the power supply
Option 1- Secure female quick connect to male quick connect. feed male quick
connect wire through conduit to power supply
Option 2- Feed wire whip to the power supply
2.1 Connect +24 VDC red wire from the fixture to the power supply +24 VDC red
wire with a wire nut. Connect -24VDC black wire from the fixture to power
supply 24VDC black wire with a wire nut.
Kendo S – Installation Instructions
Models S –
Please read all instructions prior to installation and keep for future
reference!
- PRODUCT TO BE INSTALLED BY A QUALIFIED
- USE ONIY WITH CLASS 2 POWER UNIT
- 24 V0IS DC
- SUITABLE FOR DAMP LOCATIONS
- SURFACE MOUNT ONIY ELECTRICIAN
- SUITABLE FOR INSTALLATION WITHIN THE CLOSET STORAGE SPACE
Multiple powerfeed layouts
power supplies at the end of the run
power supplies in the middle of the run.
consecutive layout, NOT RECOMMENDED
7777 Merrimac Ave
Niles, IL 60714
T 224.333.6033
F 224.757.7557
inla@luminii.com
www.luminii.com
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>