VEVOR F270 Mug Heat Press Machine User Manual

VEVOR F270 Mug Heat Press Machine

Warnings must be followed carefully to avoid bodily injury.

INTRODUCTION

1. Aluminum alloy handle
2. Pressure adjusting knob
3. Screw
4. LED Display
5. Setting knob
6. Aviation connector
7. Mug heater
8. Power socket

Accessories list

1. Startup
   After power on, short press the start button to start the machine. After startup, the machine will automatically heat up.

2. Shutdown
   Press and hold the start button for 3s to shut down.

3. Auto shutdown
   The machine will automatically shut down if there is no operation within 30min.

Temperature unit conversion

1. In shutdown state
2. Press and hold the start button for 6s.
3. Turn the switch to select the required temperature unit.
4. Short press the start button to start the machine.

Start hot stamping

1. Plug in the power cord and turn on the power
2. Short press the start button to start the machine
3. Set printing temperature and time

Parameter setting

Temperature setting:

1. Turn the display half a turn to the right.
2. Enter the temperature setting mode after a beep sound.
3. Turn the switch to the right again to increase the temperature(+).
4. Turn the switch to the left again to reduce the temperature(-).

Time setting:

1. Turn the display half a turn to the left.
2. Enter the time setting mode after a beep sound.
3. Turn the switch to the right again to increase the time(+).
4. Turn the switch to the left again to reduce the time(-).

Ready to start Parameter setting

1. Turn the display for a half turn.
2. Enter the setting mode after a beep sound.
3. Set corresponding parameters according to material type.

It is normal that the temperature will be slightly higher when the machine works for the first time.

Hot stamping process

1. Make sure that the machine reaches the set temperature before transfer printing.
2. Stick the picture on the mug
3. Hold the handle and open the machine
4. Put the mugs in from the left and right
5. Press down the handle
6. Press the countdown button to start countdown

Tips:

Pressure adjustment

1. The pressure can be adjusted manually for different sizes of mugs
2. Turn the handwheel clockwise to increase the pressure
3. Turn the handwheel counterclockwise to reduce the pressure

Tips:
Please try to keep the pressure balance at both sides.

ELECTRICAL DIAGRAM

1. D Main Control Board
2. Connect the cable
3. Power Strip
4. Down temperature sensor
5. buzzer
6. Thermal cutoff
7. Heating Filament

MAINBOARD WIRING DIAGRAM

1. Output zero line
2. input zero line
3. input live line
4. Output live line
5. Display
6. Temperature probe
7. Sensor switch (backup)

TYPE X CONNECTION

If the supply cord is damaged, it must be replaced by a special cord or assembly available from the manufacturer or its service agent.

SAFETY INSTRUCTION

Before operating this unit,please read these instructions completely and save them.
Notice:

1. Keep unplug when moving the machine.
2. Keep unplug when installing accessories.
3. Place on a flat and stable platform and operate under ventilated conditions.
4. Wear special protective equipment when operating the machine

WARNING

improper use may result in electric shock, fire, personal injury, and other damage.

1. Do not use this machine in a hazardous location.
2. Do not use it when the machine is not working properly.
3. Do not allow children or adults who do not understand this manual to operate this machine.
4. Do not disassemble and repair this machine.
5. Do not use an unsuitable AC outlet.
6. Do not touch the heating plate when the machine heating

PRODUCT PARAMETERS

• Name: Mug heat press machine
• Heating method : Electric heating coil
• Rated voltage/frequency: 220-240V~ 50Hz For Euro pean users
• Rated voltage/frequency: 120V~ 60Hz For US users
• Rated power: 620W
• Temperature range: 40° C-205° C(104 ° F-401° F) I
• Time range: 1-999s
• Model: F270
• Press pad size: L 250mm, printing diameter 87mm
• Net weight:?. 0kg Gross weight:?. 9 kg
• Outer box size: 375x380x328mm

WARRANTY

COMMON FAULT ANALYSIS

Machine temperature does not rise

| Reason 1: The aviation connector wire is not properly inserted.

Reason 2: The electric power of the mug pad is broken. Replacing the mug pad

Reason 3: The main board has no current output (the main board does not supp power to the toast coaster). Replace the motherboard.

Display error

|

Reason1: Is that the aviation connector is not inserted properly. Reason2: Is the aviation joint temperature probe wire broken.

This product is subject to the provision of european Directive 2012/19/EC. The symbol showing a wheelie bin crossed through indicates that the product
requires separate refuse collection in the European Union. This applies to the product and all accessories marked with this symbol. Products marked as such may not be discarded with normal domestic waste, but must be taken to a collection point for recycling electrical and electronic devices.

FCC

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:(1 )This device may not cause harmful interference, and (2)this device must accept any interference received. including interference that may cause undesired operation.

• Manufacturer: Yiwu Sunmeta Technology. Co., Ltd
• Address: NO.5 Xinpan Road, Shangxi Toen, Yiwu City.Zhejiang province.China
• UK Importer: FREE MOOD LTD
• Address: 2 Holywell Lane, London, England, EC2A 3ET
• EU Importer: WATCH
• Address: 250 bis boulevard Saint-Germain 75007 Paris
• I EUREP UK LTD
• Made in China
• E-mail:[email protected]

Read User Manual Online (PDF format)

Download This Manual (PDF format)

Download this manual  >>