VEVOR WP9600A Pipe Inspection System User Manual

VEVOR WP9600A Pipe Inspection System

PIPE INSPECTION SYSTEM User Manual

Applicable model: WP9600A / 9600A

This is the original instruction. Please read all manual instructions carefully before operating. VEVOR reserves clear interpretation of our user manual. The appearance of the product shall be subject to the product you received. Please forgive us that we won’t inform you again if there are any technology or software updates on our product.

ATTENTION

1. Please read the manual carefully before using it.
2. Handle it carefully during operation, avoid throwing down or pressing it heavily.
3. Please keep your distance from the system when charging.
4. After being used, turn off the display and pull out all the connection joints.

DESCRIPTION

• Colorful TFT LCD Screen
• High-resolution camera and clear picture
• Night vision
• High-quality special cable, waterproof and anti-corrosion/cold/tensile
• 12V 4500MA lithium battery
• With sun-visor for a bright environment outside
• Range of Application: Water-supply pipe, Air-conditioner pipe, Cable pipe, Pipeline vacuum system

PRODUCT SPECIFICATION

Item:|
---|---
Charger:| AC100-240V DC12.6V 1000MA
Battery:| Lithium battery 12V4500MA
Continuous use time for the battery:| Approximately 6h
Investigation depth:| 50m, 70m, 91.5m, 120m (selectable line length)
Material:| Fiber tube with high intensity
Camera light source:| High white light
Camera material:| Stainless steel
Menu languages:| Multi-language
Camera picture:| Colorful

INSTRUCTION FOR PRODUCT

Camera

Product Specification

Item:|
---|---
Camera diameter:| 23 mm
With the tube diameter:| >25mm
Camera light source:| 12 LED with high white light (adjustable)
Camera working voltage:| 5V
Lights’ working voltage:| 12V
Waterproof:| IP68
Camera material:| Stainless steel
Camera size:| 143 mm 23 mm
Camera protective cover parts material:| Plastic-steel
Camera protective cover parts size 1:| 29mm 40mm
Camera protective cover parts size 2:| 40mm* 90mm

Coil

• Cable Length Scale: The scaled cable can show the cable length
• Fixed Buckle: F ixed the cable wheel

SPECIAL DETECTION CABLE FIXER

Cell Box

1. Monitor Video
2. Power of Monitor
3. Adjacent Coil Plug
4. AV Output
5. Battery Indicator
6. Power Input for Charger
7. Light-Degree Adjustment for White Light LED
8. Power Switch
9. Power Light

System Installation

1. Vital: Turn off the power switch, connect the video camera and the monitor, or the video camera and the monitor may be damaged.
2. Connect the camera to 3-coil plug, 2-cell box and the 1-monitor. (Pic.1)
3. Turn on the power switch in the power box, the indicator light of the monitor is on, the switchboard starts.
4. Install the video camera with the protective cover slightly and put it into the pipe, rotate the coil to a proper depth.
5. Adjust LED light degree adjuster to proper light degree. For videotape, refer to the DVR operation details (display operation:Recording Type )
6. Switch video to another large screen through video line.
7. After utilization, mover the camera from the pipe carefully, take a clean, soft and dry cloth to clear up it and put it back.

Please follow these instructions carefully for a safe and successful experience with our PIPE INSPECTION SYSTEM.

This is the original instruction, please read all manual instructions carefully before operating. VEVOR reserves clear interpretation of our user manual. The appearance of the product shall be subject to the product you received. Please forgive us that we won’t inform you again if there is any technology or software updates on our product.

ATTENTIONS

1. Please read the manual carefully before using it.
2. Handle it carefully during operation, avoid throwing down or pressing it heavily.
3. please keep distance from the system when charging.
4. After being used, turn off the display and pull out all the connection joints.

DESCRIPTION

1. Colorful TFT LCD Screen.
2. High resolution camera and clear picture.
3. Night vision.
4. High-quality special cable, waterproof and anti-corrosion/cold/tensile.
5. 12V 4500MA lithium battery.
6. With sun-visor for a bright environment outside.
7. Range of Application: Water-supply pipe, Air-conditioner pipe, Cable pipe, Pipeline vacuum system, PLUNBIN pipe, Buildings, Sunken pipe.
8. Operating Temp: -10°C to 60°C

PRODUCT SPECIFICATION

INSTRUCTION FOR PRODUCT

Camera

1. Metal Contact Chip
2. Spring
3. Highlight White Led
4. Camera Lens

Product Specification

Coil

• Cable Length Scale the scaled cable can show the cable length
• Fixed Buckle fixed the cable wheel

SPECIAL DETECTION CABLE FIXER

Cell Box

1. Monitor Video
2. Power of Monitor
3. Adjacent Coil Plug
4. AV Output
5. Battery Indicator
6. Power Input for Charger
7. Light-Degree Adjustment for White Light LED
8. Power Switch
9. Power Light

System Installation

1. Vital: turn off the power switch, connect the video camera and the monitor, or the video camera and the monitor may be damaged.
2. Connect the camera to 3-coil plug, 2-cell box and the 1-monitor. (Pic.1)
3. Turn on the power switch in the power box, the indicator light of the monitor is on, the switchboard starts.
4. Install the video camera with the protective cover slightly and put it into the pipe, rotate the coil to a proper depth.
5. Adjust the LED light degree adjuster to proper light degree.
   • For videotape, refer to the DVR operation details (display operation:Recording Type )
6. Switch the video to another large screen through video line.
7. After utilization, mover the camera from the pipe carefully, take a clean, soft and dry cloth to clear up it and put it back.

Charging

When the battery power is low, it needs charging, and the method is as below:

1. Take out the battery and charger from the box.
2. Connect the charger to the battery.
3. Connect the charger to the alternating current of 100-240V. The red indicator means charging.
4. The green indicator means finishing charging.
   • Notes: To make sure the battery using age longer, please recharge it timely; otherwise, it will make it can not recharged.

TROUBLESHOOTING

Show blue screen

| 1.  Check whether the camera interface is loose, and the camera is loose,

causing poor contact.

2.  Check whether the connection of cable and power supply is normal or loose.

3.  Check whether the monitor is connected to the power supply normally.

4.  Check whether the cable is broken.

5.  Check whether there is water in the front of the camera or the camera is

damaged.

6.  When using the camera, please put on the protective cover first, so as not to cause the camera to collide with hard objects and damage, unable to display images.

Problems with LED lights

| 1.  Read the manual and check the correct way to turn on the light.

2.  Check whether there is water in the front of the camera, which causes the

LED to not light up.

Not running

| 1.  Check whether the battery power is sufficient.

2.  Check whether the display screen is damaged.

3.  Check that the display screen is connected to the power supply normally.

Photo/video cannot be saved

| 1.  Check whether the memory card is damaged and replace it.

2.  Check if there is any foreign matter or deformation in the memory card slot.

Cannot format| Memory card is damaged. Replace the memory card.

Unable to charge

| 1.  Check the charging port for foreign matters or deformation.

2.  Check whether the charger is damaged.

3.  When the battery is too low, it should be charged in time to prevent the battery from being unable to charge due to loss.

Broken cable

| 1.  It is recommended to use the cable on the pipe with a diameter ≥ 60cm. Pay attention to the force of pushing the cable to avoid breaking the detection line.

2. This product is only used for pipeline detection and inspection and cannot be used for other purposes.

---|---

Cable knotting

| 1.  When retracting and releasing cables, it shall be noted that the cables shall not be crossed and knotted, and the bending radian of cables shall not be less than 90 degrees.

2.  When retracting the cable, pay attention to cooperating with the rotating iron frame to orderly recycle, and do not use it violently.

Equipment cleaning| When cleaning the equipment, turn off the power before cleaning to avoid

damage to the equipment.

Warning

| If the fault cannot be solved, please do not disassemble it by yourself.

Please contact the after-sales service personnel.

OPERATING INSTRUCTIONS FOR HD DVR

• REC/-: To start/stop recording
• Play/+: To switch between recording and photographing. (Please refer to the icon in the top left corner) MENU: To access and loop the settings main menu / long press to rotate the screen 0, 90, 180 or 270  degrees
• > : To zoom out
• < : To zoom in the image 0-36X
• POWER: To power on/off the display screen

Main Menu Settings

1. Press MENU button the setup menu: PICTURE; OPTION; TIME; PHOTO; VIDEO
2. Press </> button to option sub-menu
3. Press REC button to adjust the setting”s value OR press REC button enter/confirm
4. Press PLAY button to exit

Recording and Photographing.

1. Press PLAY button to switch between Recording and photographing. (please refer to the icon in the top left corner)
2. Press REC button to start recording/photographing,then press REC button again to stop recording.

Photo playback on monitor

1. Loop press MENU button to find PHOTO.
2. Press </> button to find Playback.
3. Press REC button to enter,then press </> to choose one and press REC button to playback.
4. Press PLAY button to exit.

Video playback on monitor

1. Loop press MENU button to find RECORD.
2. Press </> button to find Playback.
3. Press REC button to enter, then press </> to choose one and press REC button to enter.
4. Press REC button to playback.
5. Press PLAY button to exit.

FCC INFORMATION

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

1. This device may not cause harmful interference
2. this device must accept any interference received, including interference that may cause undesired operation.

EU ENVIRONMENTAL PROTECTION

• This product is subject to the provision of European Directive 2012/19/EC. The symbol showing a wheelie bin crossed through indicates that the product requires separate refuse collection in the European Union. This applies to the product and all accessories marked with this symbol. Products marked as such may not be discarded with normal domestic waste, but must be taken to a collection point for recycling electrical and electronic devices.

• There are any minor changes to the numbers included in the user manual without prior notice.

• EUREP GmbH Unterlettenweg 1a, 85051 Ingolstadt, Germany

• Eurep Uk Ltd
  Unit 2264, 100 Ock Street, Abingdon Oxfordshire England Ox14 5dh

• EU Importer: WAITCHX

• Address: 250 bis boulevard Saint-Germain 75007 Paris

• UK Importer: FREE MOOD LTD

• Address: 2 Holywell Lane, London, England, EC2A 3ET

• Manufacturer: Shenzhen Woshijie Electronic Technology Co., LTD

• Add: 5Floor, B2B 501 Building Yingzhan Industry Park, Longtian Community,

• Pingshan District, Shenzhen, China

• E-mail: CustomerService@vevor.com

NEED HELP? CONTACT US!

• Have product questions? Need technical support? Please feel free to contact us: CustomerService@vevor.com

Documents / Resources

| VEVOR WP9600A Pipe Inspection System [pdf] User Manual
WP9600A, 9600A, WP9600A Pipe Inspection System, Pipe Inspection System, Inspection System, System
---|---

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>