SKGBLEHD01 Bluetooth Module User Manual

SKGBLEHD01 Bluetooth Module

Change Record

Version| Implementing Date| Change Reason| Change Description| Drafter
---|---|---|---|---
1.0| 2022.7.28| Initial| Initial| Yulun Zhu
 |  |  |  |
 |  |  |  |
 |  |  |  |
 |  |  |  |
 |  |  |  |
 |  |  |  |
 |  |  |  |
 |  |  |  |
 |  |  |  |
 |  |  |  |
 |  |  |  |
 |  |  |  |
 |  |  |  |
 |  |  |  |

Parameter

-93 dBm sensitivity (in 2 Mbps mode)

RAM| 128KB
FLASH| 512 KB
Quantity of GPIO| 22
Frequency of Crystal| 32 MHz
Module Size| 11.6 16.4 2.2 mm
Packaging Type| SMT
Operating Temperature| -20℃~+70℃
Storage Temperature| -40 ℃ ～ + 85 ℃
Antenna Gain （ peak ）| 2.64 dBi

Apply To

Bluetooth products

Related Record

Item| Form Number| Form Name| Department| Record Retention time
---|---|---|---|---
NA| NA| NA| NA| NA
NA| NA| NA| NA| NA

All the contents in this file belongs to SKG Health Technologies Co., Ltd. And its subsidiary corporation, No copy been Allowed before authorized by SKG

External info. & Function

Hardware & Firmware Version

Bluetooth Module model number| SKGBLEHD01| ****

---|---|---
Hardware version| H1.1|
Firmware Version| V1.0|

External Apperance And Parameter Requirements

• Mainboard PCB external size ：16.4mm(Length)*11.6mm(Width),Tolerance：±0.1mm；
• PCB Thickness : 1.2mm, Tolerance：±0.12mm。Whole Height(include Shielded enclosure): 2.2mm。

FCC & IC Statement

FCC Statement:
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:

1. This device may not cause harmful interference, and
2. this device must accept any interference received, including interference that may cause undesired operation.

Any Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

Note : This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radiofrequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

FCC Radiation Exposure Statement
This modular complies with FCC RF radiation exposure limits set forth for an uncontrolled environment. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. The module is limited to OEM installation only The OEM integrator is responsible for ensuring that the end-user has no manual instructions to remove or install module If the FCC identification number is not visible when the module is installed inside another device, then the outside of the device into which the module is installed must also display a label referring to the enclosed module. This exterior label can use wording such as the following: Contains Transmitter Module FCC ID:2AYVT-SKGBLEHD01 Or Contains FCC ID: 2AYVT- SKGBLEHD01

When the module is installed inside another device, the user manual of the host must contain below warning statements;

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

1. This device may not cause harmful interference.
2. This device must accept any interference received, including interference that may cause undesired operation.

Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. The devices must be installed and used in strict accordance with the manufacturer’s instructions as described in the user documentation that comes with the product. Any company of the host device which install this modular with limit modular approval should perform the test of radiated emission and spurious emission according to FCC part 15C : 15.247 and 15.209 requirement,Only if the test result comply with FCC part 15C : 15.247 and 15.209 requirement，then the host can be sold legally.

Antennas:

The antenna is permanently attached, can’t be replaced. Trace antenna designs: Not applicable.

ISED Statement:
This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canada ’ s licence-exempt RSS(s). Operation is subject to the following two conditions:

1. This device may not cause interference.
2. This device must accept any interference, including interference that may cause undesired operation of the device.

This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. Please notice that if the ISED certification number is not visible when the module is installed inside another device, then the outside of the device into which the module is installed must also display a label referring to the enclosed module. This exterior label can use wording such as the following: “Contains IC: 28042-SKGBLEHD01” any similar wording that expresses the same meaning may be used.

All the contents in this file belongs to SKG Health Technologies Co., Ltd. And its subsidiary corporation, No copy beenAllowed before authorized by SKG.

Form No.: FSCI-SC-S-01-005 Rev.01

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>