BRIZO 6310 Three Handle Rosette Bidet Valve Instruction Manual
- June 9, 2024
- BRIZO
Table of Contents
BRIZO 6310 Three Handle Rosette Bidet Valve
THREE-HANDLE ROSETTE BIDET VALVE WITH VACUUM BREAKER AND POP-UP ASSEMBLY
Write purchased model number here
You may need
For easy installation of your Brizo® faucet you will need:
- To READ ALL the instructions completely before beginning.
- To READ ALL warnings, care, and maintenance information.
- To purchase the correct water supply hook-up.
Contact your distributor for handle and accent options/finishes.
Specify Finish
MAINTENANCE
Bidet leaks from Rosette Spray:
SHUT OFF WATER SUPPLIES. Replace Seats & Springs (1).
If leak persists:
SHUT OFF WATER SUPPLIES. Replace Stem Unit Assembly (2).
If Bidet exhibits very low flow:
SHUT OFF WATER SUPPLIES. Clean Seats and Springs (1) of any debris. Install
stems (2) and 1/4 turn stops (3) correctly for proper handle rotation.
Note: Not all models require 1/4 turn stop
CLEANING AND CARE
Care should be given to the cleaning of this product. Although its finish is extremely durable, it can be damaged by harsh abrasives or polish. To clean, simply wipe gently with a damp cloth and blot dry with a soft towel.
INSTALLATION N OF DIVERTER VALVE/VACUUM BREAKER
Note: Please refer to bidet bowl installation instructions to identify hole location for diverter valve. Hole size must be 1-1/8” diameter minimum.
- A. Assemble diverter valve (1) with “Y” and gasket (2) as shown in the illustration. Slide one rubber cone washer (3), with smaller tapered end pointing up, onto diverter valve all the way to the base. Apply plumber tape or plumber’s putty to the elbow (4) and connect to the diverter valve (1).
- B. Insert valve from underneath and fasten into position using cone washer (1), with smaller tapered end pointing down, friction washer (2), and nut (3). Tighten securely making sure cone washers are centered and pressed into hole.
- C. Assemble escutcheon trim (1) by threading it onto diverter valve. Place handle (2) onto diverter valve stem and secure by tightening set screw (3) with allen wrench provided.
- D. Attach 24″ hose assembly (1) to elbow and one 12″ hose assembly (2) to each of the “Y” threaded connections. Tighten connections firmly but do not over-tighten.
INSTALLATION OF ROSETTE SPRAY
Insert rosette (1) and rubber washer (2) into appropriate hole in bidet bowl.
Slide rubber washer (3) & threaded nipple (4) through hole from underneath,
and thread onto rosette. Tighten securely, but do not overtighten. Assemble
24″ hose (5) from elbow on diverter to nipple of rosette sprayer. Tighten
connection firmly but do not overtighten.
INSTALLATION OF VALVE ASSEMBLIES
- A. Remove base (1) and gasket (2) from cold end valve assembly (3).
- B. Place assembly (1) through proper mounting hole from bottom. Reinstall gasket (2) and base (3) onto end valve. Tighten bottom nut (4). Repeat same steps for installation of hot end valve assembly.
- C. Thread the cold side hose (1) from the “Y” connector (2) to the cold side end valve assembly (3). Tighten connection firmly but do not overtighten. Repeat this step for the hot side hose (4).
MAKE CONNECTIONS TO WATER LINES:
Choose hook-ups for 1/2″ I.P.S. connections:
- Ball nose riser (3/8″ O.D. copper tubing), or
- 1/2″ I.P.S. faucet connector.
Use the enclosed coupling nuts (3) with the ball nose risers (1). Use two wrenches when tightening. Do not overtighten.
METAL POP-UP
- A. Remove stopper (1) and flange (2).
- B. Screw nut (1) all the way down. Push washer (2) and gasket (3) down.
- C. Remove tailpiece (1) from body (2), add plumber tape (3), replace tailpiece
- D. Apply silicone to underside of flange (1). Insert body (2) into sink. Screw flange (1) into body (2).
- E. Pivot (1) must face faucet. Pull assembly (2) down firmly and hold in place. DO NOT TWIST.
- F. Tighten nut/washer/gasket (1), clean off excess silicone (2). DO NOT TWIST
- G. Remove pivot nut (1). Install horizontal rod (2) and stopper (3) as removable (4) or nonremovable (5). Hand tighten pivot nut (1).
- H. Install rod guide assembly (1). Attach horizontal rod (2) to strap (3) using clip (4). Install lift rod (5), tighten screw (6). Connect assembly to drain.
INSTALL HANDLES:
Place handle insert (1) onto valve stem (2). Thread handle and shroud (3)
together and install onto valve stem insert. Secure handle assembly with screw
(4). Install button (5) onto handle. See maintenance section for proper valve
stem orientation.
FLUSH YOUR SYSTEM
Turn diverter handle (1) counterclockwise to ‘rim feed’ position. Turn on
water supplies (2) and turn hot and cold handles (3) to open position for one
minute to flush any debris from system. Check all connections at arrows for
leaks. Re-tighten if necessary, but do not overtighten.
OPERATING INSTRUCTIONS
- Check to be sure diverter valve handle (1) is in the rim feed position (turned fully counterclockwise).
- Turn on hot and cold water valves (3) and adjust for desired temperature.
- To divert to rosette spray, slowly turn diverter handle fully clockwise. Note: It is normal for a little water to come out of rim feed hole when system is in rosette spray position and vice versa.
- To fill bowl, pull up on lift rod knob (4). IMPORTANT: THE DIVERTER VALVE SHOULD ALWAYS BE LEFT IN “RIM FEED” POSITION WHEN BIDET IS NOT IN USE.
Limited Warranty on Brizo® Faucets
Parts and Finish
All parts (other than electronic parts and batteries) and finishes of this
Brizo® faucet are warranted to the original consumer purchaser to be free from
defects in material and workmanship for as long as the original consumer
purchaser owns the home in which the faucet was first installed or, for
commercial users, for 5 years from the date of purchase.
Electronic Parts and Batteries (if applicable)
Electronic parts (other than batteries), if any, of this Brizo® faucet are
warranted to the original consumer purchaser to be free from defects in
material and workmanship for 5 years from the date of purchase or, for
commercial users, for one year from the date of purchase. No warranty
isprovided on batteries. Delta Faucet Company will replace, FREE OF CHARGE,
during the applicable warranty period, any part or finish that proves
defective in material and/or workmanship under normal installation, use and
service. If repair or replacement is not practical, Delta Faucet Company may
elect to refundthe purchase price in exchange for the return of the product.
These are your exclusive remedies. Delta Faucet Company recommends using a
professional plumber for all installation and repair. We also recommend that
you use only genuine Brizo® replacement parts. Delta Faucet Company shall not
be liable for any damage to the faucet resulting from misuse, abuse, neglect
or improper or incorrectly performed installation, maintenance or repair,
including failure to follow the applicable care and cleaning instructions.
Replacement parts may be obtained by calling the applicable number below or by writing to:
In the United States and Mexico:
Delta Faucet Company
Product Service
55 E. 111th Street
Indianapolis, IN 46280
1-877-345-BRIZO (2749)
customerservice@deltafaucet.com
In Canada:
Masco Canada Limited, Plumbing Group
Technical Service Centre
350 South Edgeware Road
St. Thomas, Ontario, Canada N5P 4L1
1-877-345-BRIZO (2749)
Customerservice@mascocanada.com
Proof of purchase (original sales receipt) from the original purchaser must be made available to Delta Faucet Company for all warranty claims unless the purchaser has registered the product with Delta Faucet Company. This warranty applies only to Brizo® faucets manufactured after January 1, 1995 and installed in the United States of America, Canada and Mexico. DELTA FAUCET COMPANY SHALL NOT BE LIABLE FOR ANY SPECIAL, INCIDENTAL OR CONSEQUENTIAL DAMAGES (INCLUDING LABOR CHARGES) FOR BREACH OF ANY EXPRESS OR IMPLIED WARRANTY ON THE FAUCET. Some states/provinces do not allow the exclusion or limitation of special, incidental or consequential damages, so these limitations and exclusions may not apply to you. This warranty gives you special legal rights. You may also have other rights which vary from state/province to state/province. This is Delta Faucet Company’s exclusive written warranty and the warranty is not transferable. If you have any questions or concerns regarding our warranty, please view our Warranty FAQs at www.Brizo.com, email us at customerservice@deltafaucet.com or call us at the applicable number above.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>