BRIZO 106350 Pull Down, Pull Out and Prep Kitchen Faucets Instruction Manual
- June 3, 2024
- BRIZO
Table of Contents
BRIZO 106350 Pull Down, Pull Out and Prep Kitchen Faucets
Register Online
www.brizo.com/customer-support/product-registrationTo reference replacement parts and
access technical documents, product info, and cleaning and care instructions,
visit www.brizo.com
Installation Requirements
- Hole Diameter : 1 3/8” ± 1/4”
- Maximum Deck Thickness : 3” (76 mm)
- With Escutcheon : 2 3/4” (70 mm)
- Thin Gauged Sinks : Use Thin Deck Aid RP37490
You may need:
Warning: this faucet is not to be used with portable dishwashers.
Read all instructions prior to installation
CAUTION
Failure to read these instructions prior to installation may result in
personal injury, property damage, or product failure. Manufacturer assumes no
responsibility for product failure due to improper installation.
Backflow Protection System
Your Brizo® faucet pull-down spout incorporates a backflow protection system that has been tested to be in compliance with ASME A112.18.3 and ASME A112.18.1 / CSA B125.1. It incorporates two certified check valves in series, which operate independently and are integral, non-serviceable parts of the wand assembly. Should your local plumbing codes require an atmospheric type vacuum breaker, one must be purchased separately.
INSTALLATION INSTRUCTIONS
- Slide gasket, and trim ring if present, onto the tubes with paper backing oriented up.
- Remove paper backing to expose adhesive and install gasket.
- Handle assembly (depending on model): Place the handle onto the valve stem, tighten the set screw, and insert the button.
- Insert faucet into sink, ensuring it is centered in the hole.
- Install mounting hardware with supplied wrench until snug.
- Adjust final position of faucet above sink if necessary.
- Tighten hardware (method 2A or 2B depending on model) until faucet resists movement, being careful not to overtighten.
NOTICE
To avoid risk of property damage, follow instructions for proper installation.
Failure to follow these instructions may result in risk of property damage
caused by leaking at this connection. Do not use pipe dope or other sealants
on water line connections.
- Place bucket below the outlet tube.
- Turn faucet handle on, open hot and cold water lines.
- Flush lines into bucket.
- Shut off hot and cold water lines.
- Turn faucet handle off.
- Install hose weight
- Push hose end onto faucet outlet.
- Attach clip as shown.
- Pull down moderately on hose to check that hose is secure.
- Turn faucet handle on and check all connections for leaks
CUSTOM FIT CONNECTIONS
If you determine the PEX supply tubing for this faucet is too long and must be shorter to create an acceptable installation, be sure to read these instructions and plan ahead. When cutting the supply tubing, the installer accepts the responsibility to do so in a way that allows a leak-free joint to be created. Manufacturer is not responsible for tubing that is cut too short or cut in a way that will not allow for a leak-free joint. DO NOT use a metal sleeve (ferrule) or gasket (supplied with faucet) in place of the plastic sleeve (ferrule) supplied because it may not create a leak-free joint. Do not use pipe dope or other sealants on water line connections. For custom fit installations, you must use plastic sleeves (ferrules) supplied with model and nuts included on supply lines. Do not use gasket supplied with PEX tubing or brass ferrule supplied with valve stops. Tube cut must be straight and burr free. Failure to use plastic sleeve (ferrule) in the correct orientation will result in disconnection and possible water damage.
- Determine desired length of supply tube, leaving 1″- 2″ of extra length to allow for easier installation.
- Cut tube, ensuring it is cut straight and burr free.
- Slide nut and plastic sleeve (ferrule) onto supply tube. Ensure plastic sleeve is oriented as shown.
- Insert supply tube into supply valve connection. Supply tube should touch bottom of hole inside supply valve
- Slide plastic sleeve down supply tube until it contacts the supply valve connection.
- Slide nut over plastic sleeve.
- Start nut by hand to prevent cross-threading.
- Turn nut by hand until it feels snug. Then tighten nut at least two more turns with a wrench.
- Repeat for other supply line.
- Return to regular instructions.
| POTENTIAL PROBLEMS | WHAT TO DO |
|---|---|
| Tubing is not cut perpendicular to the axis of the tube. | Carefully make an |
additional cut, being careful not to cut the tube too short.
Tubing is cut too short.| Buy a coupling union and a replacement supply line
that mate together. The coupling union end intended to connect to the faucet
must mate to the standard 3/8” connection nuts and plastic sleeves (ferrules)
supplied with the faucet.
The plastic sleeve (ferrule) or connection nut is lost.| Purchase a
replacement nut and/or plastic sleeve (ferrule) that are designed to seal with
PEX tubing.
MAINTENANCE
| PROBLEM | WHAT TO DO |
|---|---|
| Faucet exhibits very low flow. | REMOVE DEBRIS: |
Unscrew aerator from sprayer wand with aerator wrench and clean debris from sprayer outlet and aerator screen.
Faucet leaks from under handle or from spout outlet.| REPLACE CARTRIDGE:
a. Insert a small screwdriver into slot in button and remove.
b. Loosen set screw inside of handle and remove handle.
c. Remove cap. If cap is threaded, rotate it counterclockwise; if it is held on by an o-ring, gently pull it away from the valve body.
d. Remove bonnet nut by rotating counterclockwise with a wrench.
e. Remove cartridge.
f. Replace cartridge and reassemble.
WARNING: Failure to securely tighten bonnet nut with a wrench could result in water damage.
NOTE: A small amount of water may run out of the spout or drip for a very short period after the faucet is shut off. This is a natural occurrence caused by the long flexible hose.
For Models 93025LF & 63925LF only.
Faucet exhibits very low flow.
| REMOVE DEBRIS:
Unscrew hose from spray head and clean debris from sprayer inlet. To remove spray head from hose, press button and turn knurled knob counterclockwise.
Limited Warranty on Brizo® Faucets
Parts and Finish. All parts (other than electronic parts, air switch power modules, batteries, and parts not supplied by Brizo Kitchen and Bath Company) and finishes of Brizo® faucets purchased from authorized Brizo sellers are warranted to the original consumer purchaser to be free from defects in material and workmanship for as long as the original consumer purchaser owns the home in which the faucet was first installed. For commercial purchasers, (a) the warranty period is ten (10) years for multi-family residential applications and (b) five (5) years for all other commercial uses, in each case from the date of purchase. For purposes of this warranty, the term “multi-family residential application” refers to the purchase of the faucet from an authorized Brizo seller by a purchaser who owns but does not live in the residential dwelling in which the faucet is initially installed, such as in a rented or leased single unit or multi-unit detached home (duplex or townhome), or a condominium, apartment building or community living center. The following installations are not considered multi-family residential ap- plications, are excluded from the 10-year warranty, and are subject to the 5-year warranty: industrial, institutional or other business premises, such as a dormitory, hospitality premises (hotel, motel, or extended stay location), airport, educational facility, long- or short-term healthcare facility (hospital, rehabilitation center, nursing, assisted or staged-care living unit), public space or common area.
Electronic Parts and Batteries (if applicable). Electronic parts (other than air switch power modules and batteries), if any, in Brizo® faucets purchased from authorized Brizo sellers are warranted to the original consumer purchaser to be free from defects in material and workmanship for five (5) years from the date of purchase or, for commercial users, for one (1) year from the date of purchase. No warranty is provided on batteries. Air Switch Power Module. The electronic power module of Brizo® air switches purchased from authorized Brizo sellers is warranted to the original consumer purchaser to be free from defects in material and workmanship for two (2) years from the date of purchase or, for commercial users, for one (1) year from the date of purchase. What We Will Do. Brizo Kitchen & Bath Company will repair or replace, free of charge, during the applicable warranty period (as described above), any part or finish that proves defective in material and/or workmanship under normal installation, use, and service.
Brizo Kitchen & Bath Company may, in its sole discretion, use new,
refurbished or recertified parts or products for such repair or replacement.
If repair or replacement is not practical, Brizo Kitchen & Bath Company may
elect to refund the purchase price in exchange for the return of the product.
These are your exclusive remedies.
What Is Not Covered. Because Brizo Kitchen and Bath Company is unable to
control the quality of Brizo products sold by unauthorized sellers, unless
otherwise prohibited by law, this warranty does not cover Brizo products
purchased from unauthorized sellers (visit Brizo.com to see a list of our
Authorized Online Resellers).
Any labor charges incurred by the purchaser to repair, replace, install or remove this product are not covered by this warranty. Brizo Kitchen & Bath Company shall not be liable for any damage to the product resulting from reasonable wear and tear, outdoor use, misuse (including use of the product for an unintended application), freezing water, abuse, neglect, or improper or incorrectly performed assembly, installation, maintenance or repair, including failure to follow the applicable care and cleaning instructions. Customized components purchased by the consumer or commercial user and installed into a Brizo product, and any damage resulting from removal or improper installation of such components, are not covered by this warranty. Brizo Kitchen & Bath Company recommends using a professional plumber for all installation and repair of faucets. We also recommend that you use only genuine Brizo® replacement parts.
What You Must Do To Obtain Warranty Service or Replacement Parts.
A warranty claim may be made and replacement parts may be obtained by calling
1-877-345-BRIZO (2749) or by contacting us by mail or online as follows
(please include your model number and date of purchase):
In the United States and Mexico:
Brizo Kitchen & Bath Company 55 E. 111th Street Indianapolis, IN 46280
Attention : Warranty Service
https://www.brizo.com/customer-support/contact-us
Proof of purchase (original sales receipt) from the original purchaser must be
made available to Brizo Kitchen & Bath Company for all warranty claims unless
the purchaser has registered the product with Brizo Kitchen & Bath Company.
This warranty applies only to Brizo® faucets installed in the United States of
America, Canada, and Mexico.
Limitation on Duration of Implied Warranties. Please note that some
states/provinces (including Quebec) do not allow limitations on how long an
implied warranty lasts, so the below limitations may not apply to you. TO THE
MAXIMUM EXTENT PERMITTED BY APPLICABLE LAW, ANY IMPLIED WARRANTY, INCLUDING
THE IMPLIED WARRANTIES OF MERCHANTABILITY AND OF FITNESS FOR A PARTICULAR
PURPOSE, IS LIMITED TO THE STATUTORY PERIOD OR THE DURATION OF THIS WARRANTY,
WHICHEVER IS SHORTER.
Limitation of Special, Incidental or Consequential Damages. Please note that some states/provinces (including Quebec) do not allow the exclusion or limitation of special, incidental, or consequential damages, so the below limitations and exclusions may not apply to you. TO THE MAXIMUM EXTENT PERMITTED BY APPLICABLE LAW, THIS WARRANTY DOES NOT COVER, AND BRIZO KITCHEN & BATH COMPANY SHALL NOT BE LIABLE FOR ANY SPECIAL, INCIDENTAL, OR CONSEQUENTIAL DAMAG-ES (INCLUDING LABOR CHARGES TO REPAIR, REPLACE, INSTALL OR REMOVE THIS PRODUCT), WHETHER ARISING OUT OF BREACH OF ANY EXPRESS OR IMPLIED WARRANTY, BREACH OF CONTRACT, TORT, OR OTHERWISE. BRIZO KITCHEN & BATH COMPANY SHALL NOT BE LIABLE FOR ANY DAMAGE TO THE FAUCET RESULTING FROM REASONABLE WEAR AND TEAR, OUTDOOR USE, MISUSE (INCLUDING USE OF THE PRODUCT FOR AN UNINTENDED APPLICATION, FREEZING WATER, ABUSE, NEGLECT OR IMPROPER OR INCORRECTLY PERFORMED ASSEMBLY, INSTALLATION, MAINTENANCE OR REPAIR, INCLUDING FAILURE TO FOLLOW THE APPLICABLE INSTALLATION, CARE AND CLEANING INSTRUCTIONS. Notice to residents of the State of New Jersey: The provisions of this warranty, including its limitations, are intended to apply to the fullest extent permitted by the laws of the State of New Jersey. Additional Rights. This warranty gives you specific legal rights, and you may also have other rights which vary from state/province to state/province. This is Brizo Kitchen & Bath Company’s exclusive written warranty, and the warranty is not transferable. If you have any questions or concerns regarding our warranty, please contact us as provided above or visit our website at www.brizo.com. © 2022 Masco Corporation of Indiana
References
- Brizo.com
- brizo.com
- brizo.com/customer-support
- brizo.com/customer-support/product-registration
- brizo.com/customer-support/contact-us
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>