taymor 33-D5030BL Sliding Door Locks Installation Guide
- June 9, 2024
- taymor
Table of Contents
taymor 33-D5030BL Sliding Door Locks
Safety Information
Read the precautions and instructions in this manual before installing and using this lock. Save this manual for future reference.
CAUTION:
Please use four alkaline batteries for the best performance
- A. Do not attempt to disassemble any internal components of the lockset personally. You will void the limited warranty.
- B. Do not drop or hit the lockset. Too much shock may result in permanent damage.
- C. Do not use pins or sharp objects to press on the keypad.
- D. Always create a backup of information you want to keep (such as the admin code and user codes). Please use the last page of this booklet as your reference.
- E. The lockset comes WITHOUT the default Admin Code. Please follow the instructions to set up the Admin Code.
CARE AND MAINTENANCE
The following instructions should be followed to properly protect and maintain your lockset:
- A. Remove locks, or do not install locks, prior to painting your door.
- B. Periodically clean with mild soap and a soft cloth only.
- C. Do not use any abrasives or chemical products containing alcohol, benzene, acids, and avoid using sharp or abrasive objects to clean this lockset.
- D. Do not allow any water or liquids into the lockset during installation.
Tools Required
WARNING
If the door needs to be drilled, be familiar with how to use your drill
safely, and understand all the door preparation steps before proceeding.
Description
Part Pieza| Description Descripción| Quantity
Cantidad
---|---|---
AA| 2-1/16″ (52 mm) Mounting Bolt / Perno de montaje de 2-1/16″ (52 mm)| 2
BB| 1-1/4″ (31.7 mm) Screw ［The correct hole sizes. Ø 2-1/8” (54 mm) ］
Tornillo de 1-1/4″ (31.7 mm) ［Los tamaños correctos de los orificios. Ø 2-1/8” (54 mm)］
| 1
CC| 3/4″ (19 mm) Screw / Tornillo de 3/4″ (19 mm)| 2
DD| 3/4″ (19 mm) Wood Screw / Tornillo de 3/4″ (19 mm)| 4
DD-1| 1-1/4″ (31.7 mm) Wood Screw / Tornillo de 1-1/4″ (31.7 mm)| 2
EE| 3″ (76 mm) Wood Screw / Tornillo de 3” (76 mm)| 2
Part Pieza| Description Descripción| Quantity
Cantidad
---|---|---
A| Key / Llave| 2
B| Exterior Assembly / Ensamble exterior| 1
C| Cylinder / Cilindro| 1
D| Torque Blade / Hoja de torsión| 1
E| Power Cable / Cable de alimentación| 1
F| Mounting Plate / Placa de montaje| 1
G| Interior Assembly / Ensamble interior| 1
H| Battery Cover / Cubierta de la batería| 1
I| Latch / Pestillo| 1
J| Bottom Plate (Optional) / Placa inferior (opcional)| 1
K| Square Or Radius Faceplate (Optional) / Placa frontal cuadrada o redonda
(Opcional)| 1
L| Drive-in Collar (Optional) / Collarín rotativo (opcional)| 1
M| Drive-in Collar (Optional) / Collarín rotativo (opcional)| 1
N| Strike Plate / Cerradero| 1
Pre-installation (continued) Door Preparation
NOTE: If your door is pre-drilled, check the hole sizes to make sure they are the proper size. If they are the proper size, skip to the INSTALLATION section.
Using the template, mark the door and drill the holes, and chisel out a mortise.
NOTE: Drill from both sides of the door to prevent wood splitting.
Prepare the door jamb – use the strike plate as a template to drill the latch and screw holes and chisel out the mortise. The strike plate must fit flush with the surface of the door jamb.
TEMPLATE
NOTE: Double check your product for the correct hole sizes.
Installation
CAUTION: Be sure the latch cam is upright before making any backset adjustment.
INSTALLING THE LOCK ASSEMBLIES
CUSTOMER SERVICE
WESTERN CANADA: 1-800-267-4774
EASTERN CANADA: 1-800-387-7064
taymor.com
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>