Taymor ASHFORD Handleset Lock Door Instruction Manual

May 15, 2024
taymor

Taymor ASHFORD Handleset Lock Door Instruction Manual
Taymor ASHFORD Handleset Lock Door Instruction Manual

INSTALLATION INSTRUCTIONS

TOOLS AND MATERIALS REQUIRED

  • Drill
  • 2-1/8” (54 mm) Hole Saw
  • 3/8” (10 mm) Drill Bit
  • 1” (25 mm) Wood Bit
  • Chisel
  • Phillips Screw Driver
  • Tape Measure

DETERMINE DOOR HANDING
Stand at the exterior side and face the door.
A. Your door is a LEFT HAND door if hinges are installed at your left hand.
HINGES

B. Your door is a RIGHT HAND door if hinges are installed at your right hand
HINGES

USE THROUGHBOLT TEMPLATE TO MARK AND DRILL HOLES

MARK DOOR
MARK DOOR

Use template attached to mark holes on door face.
A. Make mark for 1”(25 mm) hole on door edge.
B. Height 36” (914 mm) to 38” (965 mm) from floor.

DRILL HOLES

Select backset. Mark and drill holes as shown.

**IF REPLACING EXISTING HANDLESET OR INSTALLING ON PRE-DRILLED DOOR, CHECK DOOR JAMB AND DOOR PREPARATION

** Chisel outlines for strike plates until they sit flush with door edge.

CHOOSE LATCH FACE PLATE FOR HANDLESET & DEADBOLT

**RADIUS OR SQUARE CORNER MORTISE

**

Chisel 1/8” (3 mm) deep or until latch face plate is flush with door edge.

**DRIVE-IN

Dimension
Dimensions
**

CARE AND MAINTENANCE
The following care instructions should be followed to ensure a long lasting finish:

  1. Remove locks, or do not install locks, prior to painting your door.
  2. Periodically clean with mild soap and a soft cloth only.
  3. Do not use abrasives or harsh chemicals

IF NECESSARY ADJUST LATCH INSTALLATIONS FOR PROPER BACKSET

BACKSET

2-3/8” (60 mm) or 2-3/4” (70 mm)
DEADBOLT
DEADBOLT
HANDLESET
Insert Handleset Spindle for
2-3/4” Backset
2-3/8” Backset **

**SPINDLE

INSTALL HANDLESET LATCH AND DEADBOLT

  • Place sleeve over handleset latch before installation in square corner or radius corner mortise configuration
  • Do not use sleeve for installations in drive-in configuration”
    Tap latch flush
    Installation

INSTALL HANDLESET, INSIDE LEVER OR KNOB

Install Handleset

Install Inside Knob or Lever

(FOR SINGLE CYLINDER FUNCTION) INSTALL OUTSIDE CYLINDER HOUSING AND INTERIOR THUMBTURN
Install outside cylinder, and thumbturn
Deadbolt spindle in horizontal position
onto door jamb
INSTALL STRIKES

Install strikes onto door jamb
High Security Double Strike
3” (76 mm) Screws
Reinforcement Plate

  1. Outside Cylinder
  2. Deadbolt Latch
  3. Thumbturn
  4. 2-5/8” (66 mm) Deadbolt Screws (2)
  5. 1-1/4” (32 mm) Strike Screws (4)
  6. 3” (76 mm) Reinforcement Screws (2)
  7. High Security Deadbolt Strike
  8. 1-1/2” (38 mm) Dome Head Knob Screws (2)
  9. Inside Knob or Lever
  10. 3/4” (19 mm) Latch Screws (4)
  11. Rounded Corner Faceplate
  12. Handleset
  13. Handleset Latch
  14. Latch Strike
  15. Screw Cap
  16. 1-5/8” (42 mm) Handleset Post Screw (1)
  17. Washer
  18. 2-Piece Drive-In Collar for Deadbolt Latch
  19. 2-Piece Drive-In Collar for Handleset Latch
    Installation Instructions

References

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals