LANCOM ON-T90ag AirLancer Systems GmbH Instructions
- June 9, 2024
- LANCOM
Table of Contents
Mounting Instructions
LANCOM AirLancer
ON-T90ag
Mounting Instructions LANCOM AirLancer ON-T90ag
ON-T90ag AirLancer Systems GmbH
Preparation for wall mounting
Use the antenna as a drilling template to mark out the drill holes for the
wall mounting. The horizontal and vertical separation of the adjacent holes is
173.7 mm.
Size of the drill holes
Using the markings as a guide, drill the holes and insert dowels if
appropriate. Depending on the surface material the required size of the holes
may vary.
Mounting the antenna
Line-up the antenna with the holes and make sure that the connectors are
pointing downwards. Then attach the antenna with the supplied screws.
Mounting the antenna with a free orientation can be achieved with the
AirLancer Mount (ON) which is available optionally.
Operating mode 3×3 MIMO
In the 3×3 MIMO operating mode, all three antenna connectors are connected to
the same Wi-Fi module of the access point.
Operating mode 2×2 MIMO & 1×1 MIMO
Apart from its standard operation as a 3×3 MIMO antenna, this antenna can also
be used by two different Wi-Fi modules. For this purpose the connectors marked
with ‑45° and +45° are connected with the first Wi-Fi module, and the middle
connector is connected to the second Wi-Fi module. The two Wi-Fi modules
should not be operated in the same frequency band.
Please note that in this operating mode at least one antenna connector of the
access point will be unused and has to be terminated.
Important information
Responsible handling of high frequency
In order to comply with the protection requirements of EU Directive 2014/53
and EN 62479 with regard to the basic restrictions for the safety of persons
in electromagnetic fields and the „FCC Policy on Human Exposure to
Radiofrequency Electromagnetic Fields“, it is necessary to configure the
correct antenna gain in the WLAN router or WLAN access point.
Electrical and Electronic Equipment Act
Please do not dispose of electrical and electronic waste in household waste,
where it cannot be recycled. Make sure that your electrical and electronic
waste is disposed of in accordance with the currently valid guidelines of
your country.
Correct handling of antenna cables
Antenna cables are sensitive RF cables. When laying them, it is therefore
important to ensure that the cables are not kinked and are bent as little as
possible, as this can result in losses in terms of antenna performance.
Likewise, the antenna cables should not be wound into tight cable loops.
Antenna gain and termination of unused antenna ports on access points
Unused antenna connections on the access point must be terminated with an
enclosed rod antenna. For indoor access points, the terminating resistor
included with the AirLancer AN‑RPSMA‑NJ adapter can be used. In addition, the
antenna gain must be specified in the configuration of the access point.
| Technical data | ON-T90ag |
|---|---|
| Frequency range | 2,400 ‑ 2,500 MHz, 4,900 ‑ 5,900 MHz |
Antenna characteristics
Radiation patterns| horizontally 2.4 GHz: 100°
vertically 2.4 GHz: 90°
horizontally 5 GHz: 75°
vertically 5 GHz: 60°
Recommended use| Point-to-Multipoint, Sector
VSWR| 1.5:1 typ. / 2.0:1 max.
Gain| 2.4 GHz: 6 dbi max.
5 GHz: 5 dbi max.
Mechanical Data
Dimensions (mm)| 200 x 200 x 34 mm (Length x Width x Height)
Weight| 450 g (Antenna without mounting kit)
Operating temperature| ‑40 °C to 70 °C
Color| Light grey
Material| UV resistant plastic
Mounting options| Fixed wall mount, Alignable wall- and pole mount (with
optionally available AirLancer Mount (ON))
Cables & Connectors| 3x 81,2 cm UV resistant RG316 cable with N-male connector
Item
Warranty| 2 years for AirLancer and accessories
Item no.| 61241
Scope of delivery| Antenna, mounting material for fixed wall mount
LANCOM, LANCOM Systems, LCOS, LANcommunity and Hyper Integration are registered trademarks. All other names or descriptions used may be trademarks or registered trademarks of their owners. This document contains statements relating to future products and their attributes. LANCOM Systems reserves the right to change these without notice. No liability for technical errors and/or omissions. 111745 11/22
LANCOM Systems GmbH
Adenauerstr. 20/B2
52146 Wuerselen | Germany
info@lancom.de
www.lancom-systems.com
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>