Enduro Engineering 24-1419 Rubber Mounted Xtreme Skid Plate Instruction Manual
- June 12, 2024
- Enduro Engineering
Table of Contents
Enduro Engineering 24-1419 Rubber Mounted Xtreme Skid Plate
Product Information: Skid Plate
The skid plate is a protective accessory designed to shield the underside of your bike’s frame from damage caused by rocks, debris, and other obstacles encountered during off-road riding. It is compatible with various bike models and comes in two versions: Part Number 24-1419 and Part Number 24-1419X.
Product Usage Instructions: Skid Plate Installation
- Position the skid plate against the frame, ensuring a proper fit.
- Using the provided M6x16mm Hex Head Bolt, secure the plate to the rear bracket using an 8mm Socket or T-Handle Wrench. Do not fully tighten the bolt at this time (see Figure 1).
- Using the two provided M6x16mm hex head bolts, fasten the front section of the plate to the frame mounts (see Figure 2).
- Once both the front and rear bolts have been started, you can begin tightening them while pressing the plate firmly against the bike.
- Ensure all bolts are securely tightened to avoid any loose or rattling parts.
- Verify that the skid plate is properly installed and aligned with the frame.
Warning and Disclaimer: It is important to follow these installation instructions carefully to ensure proper fitting and secure attachment of the skid plate. Failure to do so may result in inadequate protection or damage to your bike. Always ride safely and responsibly.
Note: For additional information or troubleshooting, please refer to the complete user manual or contact our customer support.
SKID PLATE INSTALLATION INSTRUCTIONS
- Position the EE skid plate up against the frame. Using the Provided M6x16mm Hex Head Bolt, use an 8mm Socket or T-Handle Wrench to fasten the plate to the rear bracket, and do not tighten at this time (Fig 1).
- Using the two provided M6x16mm hex head bolt, fasten the front section of the plate to the frame mounts (Fig 2).
- Once the front and rear bolts have been started you can begin to tighten, while pressing the plate up against the bike.
- Have fun and Ride Safe!
WARNING AND DISCLAIMER
All parts manufactured, designed or sold by Enduro Engineering, Inc. (EEI) are to be installed by a licensed motorcycle dealer or a licensed motorcycle technician, Motorcycles can be dangerous. Serious injury, death and property damage can result from the use of motorcycles. This risk is increased by improper installation or misuse of after marker parts. EEI’s customers must exercise good judgement in the use, control, alteration, part selection and installation, and maintenance of their motorcycles. In the event of a possible defect in material or design, or any other defect in a part manufactured, designed or sold by EEI, the responsibility of EEI is limited to either a refund of the purchase price or the replacement of the part if EEI determines the part to be defective, and subject to EEI’s inspection of the part within thirty (30) days from the date of purchase.
(Note : any attempted repairs or modifications made to EEI Products will void this limited warranty.) EEI, under no circumstances will be responsible for incidental and/or consequential damages, property damage, personal injury damage, or damage, injury, cost or expense of any kind or nature whatsoever. By purchasing as EEI product or a product sold by EEI, you (1) acknowledge the above disclaimer and agree to its terms; (2) agree that any claim brought against EEI arising from and/or pertaining to or otherwise related to a part manufactured, designed or sold by EEI must be brought in the Michigan State Courts located in the County of Ingham or in the Federal District Court for the Western District of Michigan and the Michigan law shall apply on all issues; and (3) any claim against EEI must be brought within one (1) year of purchase of the product. EEI makes no other warranty, express or implied, including without limitation any warranties of merchantability and fitness for a particular purpose.
SKID PLATE INSTALLATION INSTRUCTIONS PART NUMBER 24-1419 & 24-1419X
enduroeng.com
517.393.2421
info@enduroeng.com
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>