KICHLER 37550 20 Inch Rosewood Plug-In Wall Sconce Instruction Manual

KICHLER 37550 20 Inch Rosewood Plug-In Wall Sconce

PACKAGE CONTENTS

PART DESCRIPTION                    QTY.

A| Canopy| 1
B| Mounting Bracket| 1
C| Socket| 1
D| Shade| 1
E| Cord| 1
F| Coupling| 1
G| On/Off Switch| 1
H| Small Thumbscrew| 3
I| Shade Adjustment Thumbscrew| 1
J| Arm Adjustment Thumbscrew| 2
K| Socket Cup| 1

HARDWARE CONTENTS

SAFETY INFORMATION

Please read and understand this entire manual before attempting to assemble, operate or install the product.

CAUTION: RISK OF SHOCK

• Disconnect Power at the main circuit breaker panel or main fusebox before starting and during the installation.

WARNING

• This fixture is intended for installation in accordance with the National Electrical Code (NEC) and all local code specifications. If you are not familiar with code requirements, an installation by a certified electrician is recommended.
• Do not use bulbs with wattage greater than specified on this fixture.
• California Proposition 65

_ WARNING: _This product can expose you to chemicals including lead, which is known to the State of California to cause cancer, birth defects, or other reproductive harm.

For more information, go to: http://www.P65Warnings.ca.gov

CAUTION

• If you have any doubts about how to install this lighting fixture, or if the fixture fails to operate completely, please contact a licensed electrical contractor.
• All parts must be used as indicated in these instructions. Do not substitute any parts, leave parts out, or use any parts that are worn out or broken. Failure to obey this instruction could invalidate the ETL listing and/or C.S.A. certification of this fixture.

PREPARATION

Before beginning assembly of product, make sure all parts are present. Compare parts with package contents list and hardware contents list. If any part is missing or damaged, do not attempt to assemble the product.

Estimated assembly time: 30 minutes to 1 hour

Tools Required for Assembly (not included): Phillips screwdriver, flathead screwdriver, wire strippers, electrical tape, ladder, safety glasses, drill, crescent wrench.

NOTE: This model can be installed as a fixture that plugs into a wall outlet, or a fixture that is directly wired to a wall-mounted outlet box.

• For Plug-In Mounting Assembly, Go to Step 1a.
• For Direct Wire Mounting Assembly, Go to Step 1b.

ASSEMBLY INSTRUCTIONS (PLUG-IN MOUNTING)

Remove ground screw from mounting bracket (B), and discard. Find a suitable location on the wall to mount your fixture (location should be within 6 feet of an electrical outlet).

Using the mounting bracket (B) as a template, place flat side of mounting bracket (B) flush against wall with the mounting hardware slots aligned vertically in the 12 and 6 o’clock position as shown. Mark locations for the two (2) mounting hardware holes, one in each mounting hardware slot. Set mounting bracket (B) aside.

• If NOT mounting fixture on a stud, Go to Step 2a.
• If mounting fixture on a stud, Go to Step 4a.

If NOT mounting fixture on a stud, drill 2a holes for mounting hardware where marked in Step 1a. Using a 11/16″ drill bit (not included), drill a 11/16″ hole at each marked location for the wall anchors (FF) and wall anchor mounting screws (EE). Remove wall anchor mounting screws (EE) from wall anchors (FF) and retain. Pass threads of wall anchor mounting screws (EE) through mounting hardware slots in the mounting bracket (B), then thread them back into wall anchors (FF) as shown.

NOTE: Wall anchor mounting screws (EE) should be threaded into wall anchors (FF) such that 2-3 threads protrude through wall anchor (FF).

Hardware Used

• FF:  Wall Anchor x 2
• EE: Wall Anchor Mounting Screw x 2

Push wall anchors (FF) through 11/16” holes drilled in wall (wall anchor (FF) is completely through wall when a “click” is heard).

While holding mounting bracket (B) flat against wall in its final mounting position, gently pull wall anchor mounting screws (EE) out and away from mounting bracket (B) such that wall anchors (FF) are flush against inside of wall surface, and tighten wall anchor mounting screws (EE) to secure mounting bracket (B) to wall anchors (FF).

If mounting fixture on a stud, drill holes for mounting hardware where marked in Step 1a. Using a 1/16″ drill bit (not included), drill a 1/16″ pilot hole at each marked location for the stud mounting screws (GG).

Hold mounting bracket (B) flat against wall (with mounting hardware slots positioned over 1/16” pilot holes) and screw stud mounting screws (GG) into pilot holes. Tighten stud mounting screws (GG) to secure mounting bracket (B) to wall.

Hardware Used

• _ GG _Stud Mounting Screw x 2

Pass canopy (A) over the screws protruding from the mounting bracket (B) and secure in place with lock washers (DD) and threaded knobs (CC).

NOTE

• Make sure all wires are inside of canopy (A) and do not get pinched between canopy (A) and mounting bracket (B), or canopy (A) and wall.
• Fixture should be mounted with socket (C) in the down position as shown.

Hardware Used

• DD Lock Washer x 2
• CC Threaded Knobs x 2

ASSEMBLY INSTRUCTIONS (DIRECT WIRE MOUNTING)

1. Remove preassembled machine screws and lock washers from mounting bracket (B) by unscrewing hex nuts, and discard machine screws, lock washers, and hex nuts.
2. Orient the mounting bracket (B) such that the mounting hardware slots align with threaded holes in the outlet box (not included) as shown. Insert long knob screws (HH) through the horizontally aligned threaded holes in the mounting bracket (B) as shown, starting from the outlet box side, with the threads of the long knob screws (HH) protruding outward.

Hardware Used

• HH Long Knob Screw x 2

1. With the long knob screws (HH) protruding outward, connect the mounting bracket (B) to the outlet box using short mounting screws (BB).

Hardware Used

• BB Short Mounting Screws x 2

1. Pull up an additional length of cord (E) into canopy (A). Cut cord (E) approximately (8) inches from center of canopy (A). Discard the remaining length of cord (E) attached to the plug.

CAUTION: Ensure cord is NOT plugged into electrical outlet when cutting the cord.

1. Remove coupling (F) from the bottom of canopy (A) by unscrewing the hex nut from the short threaded pipe protruding into the canopy (A). Discard the coupling (F), short threaded pipe, hex nut, and lock washer.

Insert hole cover (II) into hole from the outside of canopy (A) such that bottom of hole cover (II) is flush with bottom of canopy (A) when installed.

Hardware Used

• II Hole Cover x 1

1. Split the end of the cord and strip ends of each wire 1/2″ (13mm).

Wire connection guide

Ground wire

• For installation in the United States: Wrap ground wire from outlet box around ground screw preassembled on mounting bracket (B) no less than 2 in. from wire end. Tighten ground screw. If fixture is supplied with a ground wire, connect to outlet ground wire with a wire connector (AA).
• For installation in Canada: If the fixture is supplied with ground wire, wrap ground wire around ground screw on mounting bracket (B). Tighten ground screw. Connect fixture ground wire to outlet ground wire with the wire connector (AA).

Supply wires

• Connect the Neutral (White) supply wire from the outlet box to the Neutral fixture wire (Parallel Cord “D” shaped and ribbed).
• Connect the Hot (Black) supply wire from the outlet box to the Hot fixture wire (Parallel Cord round and smooth).

Hardware Used

• AA Wire Connector x 3

1. Pass canopy (A) over the long knob screws (HH) protruding from the mounting bracket (B) and secure in place with lock washers (DD) and threaded knobs (CC).

NOTE

• Make sure all wires are inside of canopy (A) and do not get pinched between canopy (A) and mounting bracket (B), or canopy (A) and wall.
• Fixture should be mounted with socket (C) in the down position as shown.
• Ideally, edge of outlet box should be flush with mounting surface. However, many outlet boxes are recessed into the surface. The long knob screws (HH) are designed to have extra length to accommodate various outlet box depths.

Hardware Used

• DD Lock Washer x 2
• CC Threaded Knobs x 2

ASSEMBLY INSTRUCTIONS (FINAL INSTALLATION STEPS)

NOTE: COMPLETE EITHER “PLUG-IN MOUNTING” OR “DIRECT WIRE MOUNTING” ASSEMBLY INSTRUCTIONS BEFORE FOLLOWING THESE FINAL INSTALLATION STEPS.

1. Carefully slip shade (D) up over socket cup (K), aligning holes in shade (D) with holes in socket cup (K). While holding shade (D) in place, screw three (3) small thumbscrews (H) into aligned holes and carefully tighten to secure shade (D) to socket cup (K).
2. Adjust shade (D) by loosening shade adjustment thumbscrew (I) and arm adjustment thumbscrews (J) at fixture joints (finger turn slightly counterclockwise), adjusting to desired position, and then re-tightening shade adjustment thumbscrew (I) and arm adjustment thumbscrews (J) at fixture joints (finger turn slightly clockwise).
   • WARNING: DO NOT COMPLETELY REMOVE THUMBSCREWS FROM FIXTURE JOINTS.
3. Insert 9-watt max. medium base bulb (LED only – not included) into socket (C).
4. If fixture was installed using “PLUG-IN MOUNTING” assembly instructions, insert plug into 120-volt electrical outlet. Turn the on/off switch (G) clockwise to switch light on/off.

CARE AND MAINTENANCE

• Always be certain that electric current is turned off before cleaning this item.
• Use a soft, moist cloth with mild non-abrasive soap to clean fixture. Never use glass cleaner on fixture, as it will damage the metal finish.

TROUBLESHOOTING

1. Fixture may be wired incorrectly.
2. Worn or broken bulb.

|

1. Check to wire.
2. Replace bulb.

ATTACH YOUR RECEIPT HERE

• Serial Number
• Purchase Date

Questions, problems, missing parts? Before returning to your retailer, call our customer service department at 800-554-6504, 8 a.m. – 4:30 p.m, EST, Monday – Friday. kichler.com/customer-care/contact-us

Distributed by: Kichler Lighting LLC
30455 Solon Rd Solon, OH 44139
Printed in China

References

• Our Locations | Kichler Lighting
• p65warnings.ca.gov

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>