CLEERLINE SSF SSF-TKITE-100 Fiber Test Kit User Manual
- June 17, 2024
- CLEERLINE SSF
Table of Contents
CLEERLINE SSF SSF-TKITE-100 Fiber Test Kit
Specifications
Type| Wavelength (nm)| Emitter Type| Output Power (dBm)| Output Power
Modulation| Fiber Type| Connector| Power Supply| Battery Life (h)| Dimension
(mm/in)| Weight (g/oz)
---|---|---|---|---|---|---|---|---|---|---
SSF-LS100SM Light Source| 1310 / 1550| FP-LD| -7| N/A| SM| SC| AAA 1.5V (3pcs
batteries)| 40| 125x65x29 / 4.92×2.56×1.14| 160 / 3.74
SSF-LS100MM Light Source| 850 / 1300| FP-LD| -7| N/A| MM| SC| AAA 1.5V (3pcs
batteries)| 40| 125x65x29 / 4.92×2.56×1.14| 160 / 3.74
Product Usage Instructions
Handheld Optical Light Source – Overview
The SSF-LS100SM Single Mode optical light source provides singleto tri wavelength output, including 1310/1550nm wavelengths for single mode fiber. The SSF-LS100MM Multimode optical light source provides single to tri wavelength output, including 850/1300nm wavelengths for multimode fiber. Together with the SSF-PM100 power meter, the optical light source provides an accurate test solution for single mode and/or multimode optical fiber networks.
Features
- Single to tri wavelength output
- SSF-LS100SM: Wavelengths – 1310/1550nm, Output Power: -7dBm
- SSF-LS100MM: Wavelengths – 850/1300nm, Output Power: -7dBm
Handheld Optical Light Source – Functions
- Label Area: Light Source will read SM (Single Mode) or MM (Multimode) depending on model. Choose MM SM for single mode testing (1310/1550nm) or MM for multimode testing (850/1300nm).
- Power On/Off: Press and hold for 1 second to turn the unit on or off.
- Auto Shut-Off Selection: While unit is on, press this key quickly to turn the auto shut-off function on or off. When auto shut-off is active the unit will automatically shut off after ten minutes idle.
- Wavelength Selection: Press this key to change the wavelength, shown in top left corner of screen.
- Modulation: Press this key to switch modulation between continuous and modulated light.
FAQ
- Q: Can I look into the laser beam when the unit is on?
- A: No, looking into the laser beam when the unit is on can cause eye damage. Please avoid doing so.
- Q: Can I take apart or repair the instrument?
- A: No, it is not recommended to take apart or repair the instrument. Please consult a professional if you encounter any issues.
- Q: Are the technical parameters subject to change?
- A: Yes, the technical parameters are subject to change without notice. Please refer to the latest version of the user manual for the most up-to-date information.
Warning
To avoid risk of eye damage, do not look into the laser beam when unit is on.
- Do not look into the laser beam when unit is on.
- To prevent damage to the instrument, do not use under high temperature, high pressure, wet, or other prohibited conditions.
- Do not attempt to take apart or repair the instrument.
Quality Assurance
Each unit meets the declared specification.
Note:
Technical parameters are subject to change without notice.
Handheld Optical Light Source
Overview
The SSF-LS100SM Single Mode optical light source provides single to tri wavelength output, including 1310/1550nm wavelengths for single mode fiber. The SSF-LS100MM Multimode optical light source provides single to tri wavelength output, including 850/1300nm wavelengths for multimode fiber. Together with the SSF-PM100 power meter, the optical light source provides an accurate test solution for single mode and/or multimode optical fiber networks.
Model: SSF-LS100SM Single Mode
- Wavelength: 1310/1550nm
- Output Power: ≥ -7dBm
Model: SSF-LS100MM Multimode
- Wavelength: 850/1300nm
- Output Power: ≥ -7dBm
Features
- Single to tri-wavelength combination
- Continuous and modulated signal
- Real time display of battery level and low power indication
- Back light function
- Auto shut-off function
- Alkaline battery operation
Specifications
| Type | SSF-LS100SM Light Source |
|---|---|
| Wavelength (nm) | 1310 / 1550 |
| Emitter Type | FP-LD |
| Output Power (dBm) | ≥-7dBM @1310 / 1550nm |
| Output Power | ±0.04 @ 20°C @ 15 min |
| Modulation | CW/270Hz/1KHz/2KHz @ others |
| Fiber Type | SM |
| Connector | SC |
| Power Supply | AAA 1.5V (3pcs batteries) |
| Operating Temperature (°C) | -10 – +50, 0 to 95% RH (no condensation) |
| Storage Temperature (°C) | -25 – +70, 0 to 95% RH (no condensation) |
| Battery Life (h) | 40 |
| Dimension (mm/in) | 125x65x29 / 4.92×2.56×1.14 |
| Weight (g/oz) | 160 / 3.74 |
| Type | SSF-LS100MM Light Source |
| --- | --- |
| Wavelength (nm) | 850 / 1300 |
| Emitter Type | FP-LD |
| Output Power (dBm) | ≥-7dBM @850/ 1300nm |
| Output Power | ±0.04 @ 20°C @ 15 min |
| Modulation | CW/270Hz/1KHz/2KHz @ others |
| Fiber Type | MM |
| Connector | SC |
| Power Supply | AAA 1.5V (3pcs batteries) |
| Operating Temperature (°C) | -10 – +50, 0 to 95% RH (no condensation) |
| Storage Temperature (°C) | -25 – +70, 0 to 95% RH (no condensation) |
| Battery Life (h) | 40 |
| Dimension (mm/in) | 125x65x29 / 4.92×2.56×1.14 |
| Weight (g/oz) | 160 / 3.74 |
Functions
Operation
Warning
- Do not look into the laser beam when unit is on. Light emitted is infrared and not visible to the human eye. To avoid the risk of eye damage, do not look into the laser at any time when the unit is active.
Turning the Unit On/Off
- Press and hold for 1 second to turn on the unit. Press and hold for two seconds to power off the light source.
- To turn the auto shut-off function on or off, with the light source turned on press .
- The unit’s automatic backlight will be enabled when the light source is turned on. It will turn off after 1 minute of inactivity. Press any key to reactivate
Laser Output
- Press to choose wavelength.
- Press to select modulation.
- The light source will output the desired laser settings
Battery Replacement
- If the battery level is low, turn off the unit immediately and replace the batteries.
- Remove the batteries if light source is not in use for an extended period of time.
Maintenance and Troubleshooting
- Always keep the connector ports of the light source clean.
- Use the regulated optical connector for testing.
- Shut off the power and cover the laser with a dust-proof cap after use.
- Plug in/remove adapters carefully.
- Regularly clean the connector.
- Remove the batteries when the light source not in use for extended periods of time.
Troubleshooting
| Issue | Possible Reason | Solution |
|---|---|---|
| Faint screen display/ No backlight | Low battery power | Replace the batteries. |
Unit fails to turn on
| Low battery power or battery inserted incorrectly| (A) Replace the battery
(B) Re-insert the
battery
Display fails to appear| Low battery| Restart or replace batteries
LCD screen will not change| ****
Low battery
| ****
Replace batteries
No laser power| Laser is off| Adjust CW/Hz
Warning
- Ensure the connector is clean before testing.
- Do not look into the laser beam when unit is on.
- Cover with laser with dust-proof cap when not in operation.
Warranty
Caution: Do not attempt to repair as doing so will void the warranty. This Optical Light Source is covered by an 18-month warranty
- We warrant that this power meter will be free from defects in material and workmanship for 18 months. Should the device fail at any time during this warranty period, we will, at our sole discretion, replace and repair or refund the purchase price of the product. The worth of the repair or replacement will not be higher than purchasing price of this unit.
- If device issues cannot be solved by the troubleshooting methods, please contact us or the local distributor directly.
- We will repair or replace the unit free of charge in case of defects in production, workmanship or material. This warranty only applies to the unit under normal operation without any damage or misuse/abuse.
- The shipping costs incurred by repair or replacement for the unit under warranty will be shared by both parties.
SSF-PM100 Optical Power Meter
Warning
- When using light source with power meter, do not look into the laser beam when unit is on. Light emitted is infrared and not visible to the human eye. To avoid the risk of eye damage, do not look into the laser at any time when the unit is active.
Handheld Optical Power Meter
Overview
The SSF-PM100 is a handheld optical power meter which can be used for absolute optical power measurements and relative loss measurements on both single mode and multimode fibers.
Model
- Wavelength: 850, 1300, 1310, 1490, 1550, 1625nm
- Measurement Range: -70 – +10dBm
Features
- High measurement accuracy and display resolution
- Quick response and measurement; real-time display of output power
- Wide measurement range (80dB)
- Six calibrated wavelengths
- Absolute and relative power measurements
- Real-time monitoring and display of batter level
- Auto shut-off function
- Backlight function
- Alkaline battery operation
Specifications
| Wavelength (nm) | 800 – 1650nm |
|---|---|
| Detector Type | InGaAs |
| Measurement Range (dBm) | -70 – +10 |
| Accuracy | <±3% (-10dBm, 22°C) |
| Calibrated Wavelength (nm) | 850, 1300, 1310, 1490, 1550, 1625 |
| Resolution (dB) | Linearity: 0.1%, Non-linearity: 0.01 dBm |
| Optical Connector | SC, LC with Adapters |
| Power Supply | Alkaline Battery (3 AAA 1.5V batteries) |
| Battery Operating Time | 120 h (without backlight) |
| Operating Temperature (°C) | -10 – +50 |
| Storage Temperature (°C) | -20 – +70 |
| Relative Humidity | 90% (+30°C) |
| Dimension (mm / in) | 125x65x29 / 4.92×2.56×1.14 |
| Weight (g / oz) | 160 / 5.64 |
Functions **
**
Operation
Turning the Unit On/Off
- Press and hold for 1 second to turn on the unit. Press and hold for two seconds to power off the power meter.
2. To turn the auto shut-off function on or off, with the light source turned on press the .
3. The unit’s automatic backlight will be enabled when the light source is turned on. It will turn off after 1 minute of inactivity. Press any key to reactivate
Absolute Power Measurement (Setting Reference Value)
- Place appropriate reference cable (LC or SC and either single mode or multimode) between units. If using an LC reference cable, install appropriate adapters and then connect the cable.
- Turn on both devices. Allow the power meter to stabilize for 1-2 minutes.
- Match the wavelength on the power meter to the light source by pressing . For multimode, 850nm is recommended. For single mode, 1310nm is recommended.
- Press to choose the power display unit (dBm or nW). Set to dBM.
- The power meter will then display the tested power value in the centre of the screen. Set this as the reference value by pressing and holding ref for two seconds. The screen will then read 0.00dBM
Relative Power Testing (Finding Loss Value)
- Perform steps above to set reference value.
- Unplug reference cable from power meter side only.
- Attach female to female adapter for connector type under test to reference cable.
- Plug cable to be tested between female adapter and power meter.
- The screen will display the loss in dB for cable under test. Optical loss will appear as a negative value (i.e. -0.57 dB).
- Press to review to review the current reference power value.
Maintenance and Troubleshooting
- Always keep the connector ports of the power meter clean.
- Use the regulated optical connector for testing.
- Shut off the power and cover laser with dust-proof cap after use.
- When using AC adapter, ensure power supply is within the required voltage range.
- Remove the batteries when power meter not in use for extended periods of time
Battery Replacement
- If the battery level is low, turn off the unit immediately and replace the batteries.
- Remove the batteries if light source is not in use for an extended period of time.
Troubleshooting
| Issue | Possible Reason | Solution |
|---|---|---|
| Faint screen display/ No backlight | Low battery power | Replace the batteries. |
Unit fails to turn on
| Low battery power or battery inserted incorrectly| (A) Replace the battery
(B) Re-insert the
battery
Display fails to appear| Low battery| Restart or replace batteries
LCD screen will not change| ****
Low battery
| ****
Replace batteries
No laser power| Laser is off| Adjust CW/Hz
Warranty
Caution: Do not attempt to repair as doing so will void warranty. This Optical Power Meter is covered by an 18 month warranty
- We warrant that this power meter will be free from defects in material and workmanship for 18 months. Should the device fail at any time during this warranty period, we will, at our sole discretion, replace and repair or refund the purchase price of the product. The worth of the repair or replacement will not be higher than purchasing price of this unit.
- If device issues cannot be solved by the troubleshooting methods, please contact us or the local distributor directly.
- We will repair or replace the unit free of charge in case of defects in production, workmanship or material. This warranty only applies to the unit under normal operation without any damage or misuse/abuse.
- The shipping costs incurred by repair or replacement for the unit under warranty will be shared by both parties.
Warning
- Ensure the connector is clean before testing.
- Do not look into the laser beam when unit is on.
- Cover laser with the dust-proof cap when not in operation.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>