TORO 76601 60in TITAN MAX Riding Mower Instructions
- June 2, 2024
- Toro
Table of Contents
76601 60 in TITAN MAX Riding Mower
Instructions
Model No. 76601—Serial No. 400000000 and Up
Model No. 76602—Serial No. 400000000 and Up
Setup
Loose Parts
Use the chart below to verify that all parts have been shipped.
| Procedure | Description | Qty. | Use |
|---|---|---|---|
| 1 | No parts required | – | Remove the machine from the crate. |
| 2 | No parts required | – | Add fuel to the machine. |
| 3 | No parts required | – | Check the engine-oil level. |
| 4 | No parts required | – | Check the hydraulic-fluid level. |
| 5 | No parts required | – | Check the tire pressure. |
| 6 | No parts required | – | Charge the battery. |
| 7 | No parts required | – | Raise the rollover-protection system (ROPS). |
| 8 | No parts required | – | Check the grass deflector. |
| 9 | No parts required | – | Check the mower adjustment. |
| 10 | No parts required | – | Check the machine before delivery to the |
customer (all machines).
11| Operator’s Manual
Engine owner’s manual
Operator-training material
Key
Registration card| 1
1
1
2
1| Deliver the machine to the customer (all machines).
Note: Determine the left and right sides of the machine from the normal operating position.
Removing the Machine from the Crate
No Parts Required
Procedure
If removing the machine from a metal crate, refer to the Dealer/Distributor
Portal for further information.
Adding Fuel to the Machine
No Parts Required
Procedure
Add fuel to the machine before starting it. Refer to your Operator’s Manual
for the correct fuel and procedure.
Checking the Engine-Oil Level
No Parts Required
Procedure
Before you start the engine and use the machine, check the oil level in the
engine crankcase; refer to Checking the Engine-Oil Level in the Operator’s
Manual.
Checking the Hydraulic-Fluid Level
No Parts Required
Procedure
This machine is shipped filled with hydraulic fluid in the reservoirs. Check
the expansion tank; if necessary, add Toro® HYPR-OIL™ 500 hydraulic fluid, as
recommended in the Operator’s Manual, to the FULL COLD line ( Figure 1 ).
Engine- Expansion tank
Checking the Tire Pressure
No Parts Required
Procedure
Pressure: 13 psi (90 kPa)
Note: Check the tire pressure before starting the machine. Refer to your
Operator’s Manual for the correct tire type and procedure.
Charging the Battery
No Parts Required
Procedure
Important: Do not run the machine with the battery disconnected;
electrical damage may occur to the engine.
- Charge the battery; refer to the Operator’s Manual for instructions.
- Connect the negative battery cable.
Note: If the positive cable is also disconnected, connect the positive (red) cable to the positive battery terminal first, then the negative (black) cable to the negative battery terminal. Slip the insulator boot over the positive terminal.
Raising the Rollover-Protection System (ROPS)
No Parts Required
Procedure
Important: Always use the seat belt with the roll bar in the raised
position.
1. Remove the hairpin cotters and remove the 2 pins ( Figure 2 ).
2. Raise the roll bar to the upright position, install the 2 pins, and secure
them with the hairpin cotters ( Figure 2 ).
Roll bar- Raised position
- Pin
- Hairpin cotter
Checking the Grass Deflector
No Parts Required
Procedure
If there are plastic ties holding the grass deflector up, remove them and
lower the deflector into place.
WARNING
An uncovered discharge opening could allow the machine to throw objects toward
you or bystanders, resulting in serious injury or death. Also, contact with
the blade could occur.
Never operate the machine without a cover plate, a mulch plate, grass
deflector, or beggar installed.
Checking the Mower Adjustment
No Parts Required
Procedure
Adjust the side-to-side level and the front-to-rear blade slope. Use the
relevant procedures in the Operator’s Manual to verify that the deck is level,
and make any adjustments as needed.
Checking the Machine Before Delivery to the Customer (All Machines)
No Parts Required
Procedure
Before delivering the machine to the customer, ensure that you have performed
the procedures listed in the following table and initial each when finished.
Refer to the Operator’s Manual for instructions on performing these
procedures.
| Initial | Check Procedure |
|---|---|
| Check the tire pressure. | |
| Check the level of the mower deck. | |
| Check the engine-oil level. | |
| Check the hydraulic-fluid level. | |
| Check that the ROPS is secure. | |
| Check the adjustment of the parking brake. | |
| Ensure that the machine tracks correctly; refer to the Operator’s Manual for |
the adjustment procedure.
| Check the safety interlock system; refer to the Operator’s Manual.
| Ensure that the PTO works.
| Check all fasteners that you installed to ensure that they are tight.
When you finish setting up the machine, sign and date in the space provided
below:
Signature: —————-
Date: ———————
Delivering the Machine to the Customer (All Machines)
Parts needed for this procedure:
| 1 | Operator’s Manual |
|---|---|
| 1 | Engine owner’s manual |
| 1 | Operator-training material |
| 2 | Key |
| 1 | Registration card |
Procedure
At delivery, fill in the model and serial number, complete the items listed in
the following table, and initial each when finished.
Model No.: ————————-
Serial No.: —————————
| Dealer Initial | Customer Initial | Check Procedure |
|---|---|---|
| Show the customer where the following features are located and how they |
function:
• Fuel tank
• Oil-fill cap/Oil dipstick
• Spark plug(s)
• Engine-oil filter
• Engine-oil drain
• Fuel gauge, valve, and hose
• Air filter
• Hydraulic-fluid reservoir
• Hydraulic filter
• Battery
• Ignition switch
• Throttle lever
• Choke (if applicable)
• Power-takeoff switch (PTO)
• Motion-control levers
• Parking brake
• Height of cut
• Lift-assist lever (if applicable)
• Adjustable seat
• Hydraulic-bypass valves
• Rollover-Protection System (ROPS)
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Dealer Initial| Customer Initial| Check Procedure
---|---|---
| | Refer to the Operator’s Manual to point out safety procedures, operation,
and maintenance procedures.
| | Review the warranty statement.
| | Describe the post-sale service procedures for your store.
| | Assist the customer in filling out and mailing the registration card or
register online at www.Toro.com.
| | Make sure that the customer receives the Operator’s Manual, engine owner’s
manual, Setup Instructions, and operator training material.
| | Make sure the customer knows that the Parts Catalog is available at
www.Toro.com.
| | Assist the customer in loading the machine.
Note: When you, the dealer representative, have finished delivering the
machine to the customer, sign and date in the space provide below and keep a
copy of this page for dealer records. Also, the dealer must remind the
customer to use a full-width trailer ramp to load the machine.
Signature: ——————————-
Date: ————————————
Signature: ——————————-
Date: ————————————
Count on it.
© 2021—The Toro® Company
8111 Lyndale Avenue South
Blooming ton, MN 55420
Register at www.Toro.com.
Original Instructions
Printed in the USA
All Rights Reserved 3449-600
Form No. 3449-600 Rev A Original Instructions (EN)
Printed in the USA
All Rights Reserved
Documents / Resources
| TORO
76601 60in TITAN MAX Riding
Mower
[pdf] Instructions
76601, 76602, 60in TITAN MAX Riding Mower, MAX Riding Mower, Riding Mower,
76601, Mower
---|---
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>