TORO H800 Rotary Mower Right Hand Blade Shaft Kit Instruction Manual

TORO H800 Rotary Mower Right Hand Blade Shaft Kit

Specifications

• Product: Right-Hand Blade Shaft Kit
• Model: ProLine H800 Rotary Mower
• Model No.: 134-8765
• Form No.: 3466-334 Rev B

Product Usage Instructions

Preparing the Machine

No Parts Required

1. Park the machine on a level surface, engage the parking brake, shut off the engine, and remove the key.
2. Thoroughly clean the cutting unit. Remove all debris to ensure that the baffles fit properly against the cutting unit.
3. Rotate the cutting unit into the maintenance position as required; refer to your machine Operator’s Manual.

Removing the Existing Spindle Assembly:

No Parts Required

1. Remove the right spindle assembly as shown in Figure 4. Refer to the service manual for the machine.
2. Set aside the parts for the installation procedure.

Installing the New Spindle Shaft and the Oil-Seal Guard

Parts needed for this procedure

• 1 Spindle shaft
• 1 Oil-seal guard

1. Use the following figures to identify the new spindle shaft and oil-seal guard (Figure 2 and Figure 3).
2. Use the previously removed parts and Figure 4 to install the new spindle shaft and oil-seal guard, refer to the service manual for the machine.

Important: The new oil-seal guard has a left-hand thread. Turn the new oil-seal guard counter-clockwise to tighten it.

Torque the blade bolt to 53 Nm (39 ft-lb).

Discard the old spindle shaft and the old oil-seal guard.

Note: Determine the left and right sides of the machine from the normal operating position. Install this kit onto machines with the following serial numbers.

Installation

Preparing the Machine

No Parts Required

Procedure

1. Park the machine on a level surface, engage the parking brake, shut off the engine, and remove the key.
2. Thoroughly clean the cutting unit. Remove all debris to ensure that the baffles fit properly against the cutting unit.
3. Rotate the cutting unit into the maintenance position as required; refer to your machine Operator’s Manual.

Removing the Existing Spindle Assembly

No Parts Required

Procedure

1. Park the machine on a level surface, engage the parking brake, shut off the engine, and remove the key.
2. Thoroughly clean the cutting unit. Remove all debris to ensure that the baffles fit properly against the cutting unit.
3. Rotate the cutting unit into the maintenance position as required; refer to your machine Operator’s Manual.

Installing the New Spindle Shaft and the Oil-Seal Guard

Parts needed for this procedure

• 1 Spindle shaft
• 1 Oil-seal guard

Procedure

1. Use the following figures to identify the new spindle shaft and oil-seal guard (Figure 2 and Figure 3).
   Note: The new spindle shaft has 2 grooves and the new oil-seal guard has a groove for identification.

2. 1. Right-hand threads

3. Existing spindle shaft

4. Groove

5. Left-hand threads

6. New spindle shaft

7. Grooves

8. 1. Existing oil-seal guard

9. Right-hand threads

10. New oil-seal guard

11. Left-hand threads

12.  Groove

13. Use the previously removed parts and Figure 4 to install the new spindle shaft and oil-seal guard, refer to the service manual for the machine.
    Important: The new oil-seal guard has a left-hand thread. Turn the new oil- seal guard counter-clockwise to tighten it.Spindle shaft

14. Oil-seal guard

15. Torque the blade bolt to 53 N∙m (39 ft-lb).

16. Discard the old spindle shaft and the old oil-seal guard.

FAQ

Q: Can this kit be installed on any other mower models?

A: This kit is specifically designed for machines with the specified serial numbers mentioned in the manual. Installing it on other models may not be compatible or recommended.

Q: What maintenance is required after installing the kit?

A: Regularly check the tightness of the blade bolt and ensure proper alignment of the cutting unit for optimal performance.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>