TORO 44703 ProPass Top Dresser Instruction Manual
- May 15, 2024
- Toro
Table of Contents
TORO 44703 ProPass Top Dresser
Product Information
Specifications
- Product Name: Conveyor and Swivel Kit for ProPassTM 200 TopDresser
- Model No.: 44703
- Form No.: 3467-198 Rev A
- Country of Origin: USA
Product Usage Instructions
Installation
- Before installing the cross conveyor, install the side-railplates using the supplied bolts.
- If using a twin spinner on the top dresser, replace spacers as instructed to maintain side-rail plates.
- Mount the swivel and sliding guard to the swivel assembly with provided bolts and nuts, leaving some bolts loose.
- Attach handle and deflector strap to the conveyor with bolts, washers, and nuts.
- Lift the swivel into position on the top dresser with an assistant, aligning plastic bearing locations.
- Clamp the swivel to the top dresser using quick attach latches, adjusting if needed for a snug fit.
- Check clearance of the adjustable belt guard to the conveyor belt, adjusting if necessary.
- Install the sensor bracket to the swivel guard using the provided bolts, washers, and nuts.
Frequently Asked Questions (FAQ)
Q: What should I do if a safety decal is damaged or missing?
A: Replace any damaged or missing safety decals as they are crucial for
operator safety and awareness.
Q: Can I transport the machine with the conveyor extended?
A: It is advised not to transport the machine when the conveyor is
extended. Only transport it when the conveyor is in the stored position to
prevent any damage.
Q: How do I adjust the clearance of the adjustable belt guard?
A: If the gap between the belt and guard is more than 5/8 cm (1/4 inch),
loosen the bolts and slide the guard until it is about 1/4 inch from the main
conveyor belt on the top dresser.
This product complies with all relevant European directives. For details, please see the Declaration of Incorporation (DOI) at the back of this publication.
Safety
Safety and Instructional Decals
Safety decals and instructions are easily visible to the operator and are
located near any area of potential danger. Replace any decal that is damaged
or missing.
- Entanglement hazard, belt—stay away from moving parts,keep all guards and shields in place.
-
Read the Operator’s Manual.
-
Use 2 people required to lift.
-
Entanglement hazard, shaft—stay away from moving parts, keep all guards and shields in place.
-
Warning—do not transport the machine when the conveyor is extended; only transport the machine when the conveyor is in the stored position.
Installation
Note: Before installing the cross conveyor to the top dresser, install the side-rail plates. Using the bolts supplied with the kit, install the left and right side plates (Figure 1). Ensure that the scraper remains in contact with the belt when securing the brackets.
-
If you plan to use a twin spinner on the same top dresser, remove the top plastic spacer (3/8 inch) as shown in Figure 2, as well as the metal spacer (1/4 inch) and replace them with the plastic and metal spacers provided. This allows the previously installed side-rail plates to remain in place whether you install a twin spinner or conveyor and swivel kit.
-
Remove the swivel and conveyor from the crate.
-
Mount the swivel and sliding guard to the swivel assembly with the 7 bolts and nuts.
Note: Leave the 4 bolts holding the guards together loose. -
Mount the handle and deflector strap to the conveyor bolts, washers, and nuts.
-
Leaving the conveyor attached to the swivel, having an assistant help you, lift the swivel into position and align the plastic bearing locations with the mounting brackets arrows (Figure 3).
-
Clamp the swivel to the top dresser using the quick attach latches.
Note: If the latches are not snug when clamping, loosen the 2 bolts (1/4 inch) on the latches and adjust them until the latches clamp tight enough to keep the swivel snug on the top dresser (Figure 4). -
Check the clearance of the adjustable belt guard to the top-dresser conveyor belt.
Note: If the gap between the belt and the adjustable guard is greater than 5/8 cm (1/4 inch), loosen the 4 bolts (1/4 inch) and slide the guard until it is about 1/4 inch from the main conveyor belt on the top dresser (see the arrows in Figure 5).
-
Install the sensor bracket to the swivel guard using 2 bolts (1/4 x 3/4 inch), 8 thrust washers, and 2 nuts (1/4 inch) as shown below.
-
Machines with a proximity sensor only:
Adjust the clearance between the proximity sensor and sensor bracket to 3 mm (1/8 inch).
The gap should be no wider that 6 mm (1/4 inch).
Note: The proximity sensor must not touch the sensor bracket.
-
Pin the conveyor in the travel position with the motor on the right side of the top dresser (Figure 8).
-
Connect the hoses as shown in Figure 9.
Note: Ensure that the pin goes through both plates.
Declaration of Incorporation
The Toro Company, 8111 Lyndale Ave. South, Bloomington, MN, USA declares that
the following unit(s) conform(s) to the directives listed, when installed in
accordance with the accompanying instructions onto certain Toro models as
indicated on the relevant Declarations of Conformity.
Model No.| Serial No.| Product Description| Invoice
Description| General Description| Directive
---|---|---|---|---|---
44703| —| Conveyor and Swivel Kit| PROPASS CONVEYOR
/ SWIVEL ASM
| Conveyor and Swivel| 2006/42/EC,
2000/14/EC
Relevant technical documentation has been compiled as required per Part B of
Annex VII of 2006/42/EC.
We will undertake to transmit, in response to requests by national
authorities, relevant information on this partly completed machinery. The
method of transmission shall be electronic transmittal.
This machinery shall not be put into service until incorporated into approved
Toro models as indicated on the associated Declaration of Conformity and in
accordance with all instructions, whereby it can be declared in conformity
with all relevant Directives.
Certified:
Tom Langworthy
Engineering Director
8111 Lyndale Ave. South
Bloomington, MN 55420, USA
February 13, 2024
Authorized Representative:
Marcel Dutrieux
Manager European Product Integrity
Toro Europe NV
Nijverheidsstraat 5
2260 Oevel
Belgium
UK Declaration of Incorporation
The Toro Company, 8111 Lyndale Ave. South, Bloomington, MN, USA declares that
the following unit(s) conform(s) to the regulations listed, when installed in
accordance with the accompanying instructions onto certain Toro models as
indicated on the relevant Declarations of Conformity.
Model No.| Serial No.| Product Description| Invoice
Description| General Description| Directive
---|---|---|---|---|---
44703| —| Conveyor and Swivel Kit| PROPASS CONVEYOR
/ SWIVEL ASM
| Conveyor and Swivel| 2006/42/EC,
2000/14/EC
Relevant technical documentation has been compiled as required per Schedule 10 of S.I. 2008 No. 1597.
We will undertake to transmit, in response to requests by national
authorities, relevant information on this partly completed machinery. The
method of transmission shall be electronic transmittal.
This machinery shall not be put into service until incorporated into approved
Toro models as indicated on the associated Declaration of Conformity and in
accordance with all instructions, whereby it can be declared in conformity
with all relevant Regulations.
This declaration has been issued under the sole responsibility of the
manufacturer.
The object of the declaration is in conformity with relevant UK legislation.
Tom Langworthy
Engineering Director
8111 Lyndale Ave. South
Bloomington, MN 55420, USA
February 13, 2024
Authorized Representative:
Marcel Dutrieux
Manager European Product Integrity
Toro U.K. Limited
Spellbrook Lane West
Bishop’s Stortford
CM23 4BU
United Kingdom
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>