AENO AGS0003 Handheld Garment Steamer User Manual
- June 3, 2024
- AENO
Table of Contents
AENO AGS0003 Handheld Garment Steamer
The AENO GS3 garment steamer is designed to remove creases and wrinkles in fabric, improve the appearance of different types of fabric using a powerful steam jet.
Specifications
Voltage: AC 220–240 V; Frequency: 50/60 Hz. Power: 1500.0 W. Dimensions (length × width × height): 201 mm × 128 mm × 293 mm. Water tank volume: 0.25 l. Steam modes: 35 g/min (high), 30 g/min (medium), 15±3 g/min (low). Steam temperature: up to +160 °C.
Package Contents
AENO GS3 steamer (1), brush head (4), measuring cup (5), quick start guide, warranty card.
Limitations and Warnings
WARNING! The device connected to the mains is live even after it has been turned off by the power button (6); unplug it immediately after use, before cleaning, filling and emptying the water tank (2). Do not allow the body of the steamer or the power cord to come in contact with water. Do not leave the device plugged in unsupervised. Do not allow children to use or play with the device. Do not turn on a damaged device. Use the device indoors only. Unplug the device by holding the power plug, not the cord; do not use an extension cord. The working surface of the steamer head gets hot during operation, do not touch hot surfaces. Do not point the nozzle at people. Never steam clothes on a person. Check the care label before steaming. Use only distilled water.
Before the first use
Unpack the device. Place it on a stable horizontal surface without plugging it in. Fill the water tank as shown in figure C. It is recommended to use the measuring cup (5) provided for filling the device.
Operating the device
Connect the device to the mains by inserting the power plug into the power outlet. Press the power button (6): the blue light (7) will light up, the red light (8) will blink. Wait about 35 seconds for the steam to build up. Quiet crackling during heating is allowed. The device is ready for operation when the red indicator (8) is lit steadily. Place the item to be steamed vertically or horizontally. Select the steam mode using the “+/-” button (9). Point the steamer head away from yourself and those present, release the first batch of steam, point the steamer head at the surface to be steamed. Start steaming by pressing steam button (10). Press the steam button (10) again to stop steaming. Press the power button (6) to turn the device off. Drain the remaining water from the water tank.
Steam modes (adjustable with the “+/-” button (9)):
- low (one indicator light (8) of steam mode is on) – delicate fabrics/light wrinkles;
- medium (two indicators (8) of steam mode are on) – everyday clothes made of cotton, polyester/medium creases;
- high (three indicators (8) of steam mode are on) – heavy fabrics/strong wrinkles.
WARNING! When using the device for the first time, check the operation of the device on old clothing: it is possible that dust accumulated in the device during production and transportation.
Note : For better steaming, it is recommended to use the brush head (4). Install the brush head only on the unit when it is turned off and cool.
Auto Power Off Mode
If there is no operation in 15minutes, the power supply is automatically turned off.
Troubleshooting
- The steamer is not heated. Possible causes: the device is not turned on or not connected to the power supply. Solution: Make sure that the unit is turned on, the power plug is connected to the socket outlet, and the socket outlet is in proper condition.
- The steamer does not produce steam. Possible causes: low water level in the water tank; the water tank is installed incorrectly; device is not turned on or not plugged in. Solution: unplug the device and fill the water tank; install the water tank as shown in Figure C; make sure the steamer is turned on and plugged in, and the socket outlet is in good condition.
- Water drips from the steamer head or leaks out of the tank. Possible causes: the steamer is not heated to the desired temperature; the water tank cap (3) is not properly closed. Solution: wait (about 35 seconds) for the red indicator light (8) to light steadily; install the water tank as shown in figure C.
WARNING! If none of the possible solutions solves your problem, contact your supplier or service center. Do not disassemble or attempt to repair the device yourself.
Recycling information
These symbols indicate that you must follow the Waste Electrical and
Electronic Equipment (WEEE) and Waste Battery and Battery Regulations when
disposing of the device, its batteries and accumulators, and its electrical
and electronic accessories. According to the rules, this equipment must be
disposed of separately at the end of its service life. Do not dispose of the
device, its batteries and accumulators, or its electrical and electronic
accessories together with unsorted municipal waste, as this will harm the
environment. To dispose of this equipment, it must be returned to the point of
sale or turned in to a local recycling facility. You should contact your local
household waste disposal service for details. ASBISc reserves the right to
modify the device and to make edits and changes to this document without prior
notice to users. The warranty period and service life shall be 2 years as from
the date of purchase of the device. Manufacturer: ASBISc Enterprises PLC,
Lapetou, 1, Agios Athanasios, 4101 Limassol, Cyprus. Made in China. For
current information and details on the device description and specification,
as well as connection process, certificates, warranty, and quality issues, see
relevant Installation and Operation Manuals available for downloading at
aeno.com/documents. All trademarks and names herein are the property of their
respective owners. aeno.com
References
- Home appliances AENO - Smart home appliances on the official website of the manufacturer AENO in Europe
- Documents | AENO in Europe
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>