AENO AAP0001S Air Purifier AP1S User Manual

: June 3, 2024
: AENO

Table of Contents

AENO AAP0001S Air Purifier AP1S
Specifications
Package Contents
Limitations and Warnings
Components of the Air Purifier
Button Panel Control
Maintenance
Troubleshooting
Connection to the AENO mobile app
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

AENO AAP0001S Air Purifier AP1S

AENO-AP0001S-Air-Purifier-AP1S-product-img

How to connect $AENO-AP0001S-Air-Purifier-AP1S-fig- $3$$

The AENO AP1S Air Purifier is a household appliance designed to disinfect and clean indoor air from allergens, pollen, fungal spores, dust particles, smoke, animal hair, and unpleasant odors.

Specifications

Input voltage : 100–240 V (AC);
frequency: 50/60 Hz.
Rated power: 50 W.
Operating temperature: –10 °C to +50 °C.
Dimensions (L × W × H): 270 mm × 303 mm × 497 mm.
Efficiency: 450 m3/h.
Coverage: up to 60 m²
Indoor air purification time: 0,5 hours
Noise level : in the night mode 25 dB (at a distance of 1 m)
Built- in UV LED
HEPA filter operation time : 2,200 hours.
Emission power : +20 dBm/100 mW.

Package Contents

AENO AP1S Air Purifier
HEPA filter H13 H13
quick start guide
warranty card.

Limitations and Warnings

ATTENTION! The device is equipped with a built-in UV LED. It is not allowed to disassemble the device and turn it on when disassembled, because it may be very harmful for eyes.

Make sure the purifier is unplugged before maintenance.
Do not immerse the purifier in water or any other liquid.
After the end of the life of the HEPA filter, do not turn on the purifier until you replace the expired HEPA filter.
Do not use aggressive and flammable chlorine- or alcohol-containing agents to clean the purifier.
Water is not allowed to enter the body of the purifier.
Never rinse the HEPA filter with water, and never clean it with a damp cloth.
Use the device as described in this Quick Start Guide and the complete User Manual only.
Failure to follow the instructions may result in fire and other hazardous situations, as well as injuries.
Do not use the device if it is damaged or cracked.
Do not install the device outdoors or near sources of water, including humidifiers.
Do not expose the device to direct sunlight, moisture or vibration.
Do not drop, throw, disassemble the device, or try to repair it on your own.
Do not lay the power cable near radiators, stoves, or heaters.
Do not use cleaning agents or detergents to clean the device.
Do not dispose of the device with unsorted urban waste, because this will be harmful for the environment.
For more information on proper disposal, please contact your local waste collection and disposal company.
Keep children away from the device. There is a risk of serious injury and electric shock.
This device is intended for use by adults only.
Warnings, precautions, and instructions contained herein may not contain every possible hazardous situation.
Please use common sense when operating the device

Components of the Air Purifier

(see figure a)

Control panel
Air holes
Housing
Air intake
Backlight
Infrared sensor
HEPA filter
Back cover.

ATTENTION! Never disassemble the purifier except for removal of the HEPA filter for cleaning.

Button Panel Control

The control panel of the device contains the following 5 LED buttons (see Figure b):

The ON/OFF button used to turn the purifier on and off;
The MODE button used to adjust the power of the purifier. The following four modes are available:
- AUTO, i.e. an automatic mode, when the operating power of the purifier is automatically selected based on the degree of air pollution;
- H, i.e. the high power;
- M, i.e. the medium power;
- i.e. the low power, or the Sleep Mode. To select the operating mode, you should press the MODE button.
  The LED will indicate the current operating mode after a short beep;
The TIMER button used to set operating time of the purifier. There are three operating time modes (in sequence) as follows: 2H, 4H and 8H (2 hours, 4 hours and 8 hours, respectively). Upon timer expiration, the purifier turns off. This button is also used to activate the Wi-Fi mode of the purifier in order to manage it from your smartphone. For more details, please read the complete installation and operation manual available at aeno.com/documents;
The LIGHT button used to change the backlight of the purifier in three modes (in sequence) as follows:
- Soft – soft light;
- Standard – normal light;
- Off – no light.
  If you press and hold this button for more than 3 seconds, the purifier will enter the Child Lock Mode where all buttons will be locked.
  To disable the Child Lock Mode, press and hold the button again for 3 seconds;
The button (UV/FILTER) used to turn on the UV diode for disinfection. If you press this button again, the UV diode will be turned off.
After 2,200 hours of operation, the HEPA filter will be completely dirty. In this case, the UV/FILTER LED will start blinking red. You may stop it by pressing and holding this button for at least 7 seconds.

Maintenance

Make sure the purifier is turned off and unplugged before cleaning or replacing the HEPA filter.
Remove the HEPA filter from the device body to clean it from dust.
Shake off dust and dirt, and remove residues with a dry cloth or brush only.
Use a soft cloth with a neutral (non-aggresive) detergent to remove dust or large pieces of dirt from the surface of the HEPA filter.
The HEPA filter shall be installed back in the purifier casing after cleaning.
If the device is not planned to be used for a long time, please store it covered with a dustproof bag in a dry, cool and well-ventilated area.
It is also recommended to power on the device from time to time for at least a few minutes in order to keep it in a good working condition. .

Troubleshooting

The purifier does not turn on. Possible causes and solutions: Make sure that the purifier is plugged into the mains socket, and that there is no power supply failure, as well as that the circuit breaker is on, and that the fuses are intact, and that the filter change LED is blinking red.
Dust is poorly removed. Possible causes and solutions: Make sure that the filter surface is not clogged and that there are no obstructions preventing air intake or discharge.
The device makes a loud noise. Possible causes and solutions: Make sure that nothing is stuck in the fan, and that the purifier is not tilted. If the noise is still too loud, try to reduce the fan speed using MODE button. Also, use Sleep Mode to operate the purifier at night.
Unpleasant odor coming out from the purifier. If the device emits a plastic smell during the first few hours of operation, this is deemed to be normal However, the device may also emit an unpleasant odor when the filter is clogged. In this case, the filter must be cleaned or replaced. If you smell burning, unplug the purifier immediately. Then, contact our Support Dept or the Seller of the device for assistance.
The filter change LED is blinking after the filter was replaced or cleaned. Possible causes and solutions: Press and hold the UV/FILTER button for at least 7 seconds. The filter replacement timer will restart, and the indicator will turn off.

ATTENTION! If your problem persists, please contact your local supplier or the service center for support. Please do not disassemble the device or try to repair it on your own

Connection to the AENO mobile app

ATTENTION! Please make sure that your phone is connected to a 2.4 GHz Wi- Fi network as 5 GHz networks are not supported by the device.

Connect the device to a power supply and turn it on.
Download the AENO mobile app from Google Play or the App Store and create a new account or log in to your user account.
On the main screen of the app, tap “+” or “Add device” (if there are no added devices in the app). Select “Air purifier” in the window that opens.
Note : If the system prompts you to turn on any features on your smartphone, follow the recommendations in the prompts.
Enter your Wi-Fi network name and password if the fields have not been filled in automatically. Tap “Next”. Make sure that the EZ mode is selected in the upper right corner.
If the Wi-Fi icon on the device control panel is blinking, go to the next step of the instructions. If the Wi-Fi icon is not blinking, press and hold the “TIMER” button for about 7 seconds until it starts blinking.
On the “Tips to Connect Devices” screen, check the “Make sure that the LED indicator is blinking” box and tap “Next”.
Wait for the “Device successfully added” message to appear *.
Note: It is recommended to stay as close as possible to the device and, if possible, to the router at the moment of connection to ensure a stable Wi- Fi signal. After that, you will be able to control your device from the app. To learn about remote control scenarios, see the full manual at aeno.com/documents

Recycling information

These symbols indicate that you must follow the Waste Electrical and Electronic Equipment (WEEE) and Waste Battery and Battery Regulations when disposing of the device, its batteries and accumulators, and its electrical and electronic accessories. According to the rules, this equipment must be disposed of separately at the end of its service life.
Do not dispose of the device, its batteries and accumulators, or its electrical and electronic accessories together with unsorted municipal waste, as this will harm the environment.
To dispose of this equipment, it must be returned to the point of sale or turned in to a local recycling facility.
You should contact your local household waste disposal service for details.
The warranty period and service life shall be 2 years as from the date of purchase of the device.

ASBISc reserves the right to modify the device and to make edits and changes to this document without prior notice to users.
The warranty period and service life shall be 2 years as from the date of purchase of the device.
Manufacturer: ASBISc Enterprises PLC, Iapetou, 1, Agios Athanasios, 4101 Limassol, Cyprus. Made in China. For current information and details on the device description and specification, as well as connection process, certificates, warranty and quality issues, see relevant Installation and Operation Manuals available for downloading at aeno.com/documents. All trademarks and names herein are the property of their respective owners.
In case of a connection failure, make sure that the device is connected to the power supply and turned on, and the Wi-Fi icon on the device control panel is blinking. Press the “TIMER” button on the control panel again until you hear a beep and the Wi-Fi icon starts blinking. Additionally, check your router’s Wi- Fi (aeno.com/router-help) settings or restart it, and then repeat the connection process.

aeno.com/documents
aeno.com