AENO AAP0004 iPon Cooling Air Purifier AP4 User Manual
- June 3, 2024
- AENO
Table of Contents
AENO AAP0004 iPon Cooling Air Purifier AP4
The AENO AP4 Air Purifier is designed to disinfect and clean indoor air from allergens, pollen, fungal spores, dust particles, smoke, animal hair, and unpleasant odors.
OVERVIEW
Specifications
Supply voltage: DC 12 V, 2 A. Rated power: 24 W. Power adapter input voltage: AC 100–240V, 50/60 Hz. Air flow rate: 200 m3/h. Noise level: in the night mode 22 dB (at a distance of 1m). Coverage: Up to 35 m2. Indoor air purification time: 0,5 hours. Net weight: 2.1 kg. Dimensions: Ø205 mm × 385 mm.
Package Contents
AENO AP4 Air Purifier (See Figure a), power adapter, HEPA filter, quick start guide, warranty card.
Limitations and Warnings
ATTENTION! The device is equipped with a built-in UV lamp. It is not allowed to disassemble the device and turn it on when disassembled, because it may be very harmful to eyes. Make sure the purifier is unplugged before maintenance. Do not immerse the purifier in water or any other liquid. Do not use aggressive and flammable chlorine- or alcohol-containing agents to clean the purifier. Use the device as described in this Quick Start Guide and the complete User Manual only. Failure to follow the instructions may result in fire and other hazardous situations, as well as injuries. Do not use the device if it is damaged or cracked. Do not install the device outdoors or near sources of water, including humidifiers. Do not expose the device to direct sunlight, moisture or vibration. Do not drop, throw, disassemble the device, or try to repair it on your own. Do not lay the power cable near radiators, stoves, or heaters. Do not use cleaning agents or detergents to clean the device. Do not dispose of the device with unsorted urban waste, because this will be harmful for the environment. For more information on proper disposal, please contact your local waste collection and disposal company. Keep children away from the device. There is a risk of serious injury and electric shock. This device is intended for use by adults only.
Warnings, precautions, and instructions contained herein may not contain every possible hazardous situation. Please use common sense when operating the device.
Initial Setup
Before operation, you should remove the packaging from the HEPA filter. To do this, please turn the purifier upside down and remove its cover by turning it counterclockwise (See Figure b). Then, remove the HEPA filter from the device body using the fabric strips (See Figure c), remove the filter packaging, and insert the filter back into the device body. Tighten the cover by turning it clockwise (See Figure d). After that, you should connect the air purifier to the source of power (mains socket) using the power adapter included in the package of supply. The power connector of the adapter must be inserted into the power port in the device casing, while the plug of the adapter – into the mains socket.
ATTENTION! Never use a non-original power adapter to connect to and power on the device, as this may damage the purifier.
Button Panel Control
The purifier will be switched to the Standby Mode upon connection to the mains socket using the power adapter. The control panel of the device contains the following 6 LED buttons (See Figure e):
- POWER button used to switch the purifier from the Standby Mode to the Operation Mode, as well as to turn off the purifier, or turn on the anion filter.
- SLEEP, SPEED MID and SPEED HIGH buttons used to switch the fan speed of the purifier in the following way: Sleep – quiet mode, Speed Mid – medium rotation speed of the fan, Speed High – high rotation speed of the fan;
- FILTER button that is blinking every time the filter shall be replaced (an audible signal will also be emitted. You may stop it by pressing this button again);
- UV-C button used to turn on the UV diode intended for air disinfection.
Maintenance
The HEPA filter shall be cleaned on a regular basis, but never rinsed up with water or used after the end of service life. Please dry the HEPA filter regularly in the sun. Do not remove dust from the HEPA filter with a vacuum cleaner or a water jet. The HEPA filter shall be replaced every 2,200 hours of operation (i.e. every 3-6 months). To remove dust from the HEPA filter, you shall remove it from the purifier casing. Use a soft cloth with a neutral (non-aggresive) detergent to remove dust or large pieces of dirt from the surface of the HEPA filter. The HEPA filter shall be installed back in the purifier casing only after it gets dried. If the device is not planned to be used for a long time, please store it covered with a dustproof bag in a dry, cool and well-ventilated area. It is also recommended to power on the device from time to time for at least a few minutes in order to keep it in a good working condition.
ATTENTION! Do not allow water to enter the purifier.
Troubleshooting
- The purifier does not turn on. Make sure that the purifier is plugged into the mains socket, and that there is no power supply failure, as well as that the circuit breaker is on, and that the fuses are intact, and that the filter change LED is blinking red.
- The device makes a loud noise. Make sure that nothing is stuck in the fan, and that the purifier is not tilted. If the noise is still too loud, try to reduce the fan speed using the Speed Mid or the Sleep button. Also, use Sleep Mode to operate the purifier at night.
- Unpleasant odor coming from the purifier. If the device emits a plastic smell during the first few hours of operation, this is deemed to be normal. However, the device may also emit an unpleasant odor when the filter is clogged. In this case, the filter must be cleaned or replaced. If you smell burning, unplug the purifier immediately. Then, contact our Support Dept or the Seller of the device for assistance.
- The filter change LED is blinking after the filter was replaced or cleaned. Click on the Filter button to restart the filter replacement timer, and the LED indicator will be turned off.
ATTENTION! If your problem persists, please contact your local supplier or the service center for support. Please do not disassemble the device or try to repair it on your own.
Recycling information
These symbols indicate that you must follow the Waste Electrical and Electronic Equipment (WEEE) and Waste Battery and Battery Regulations when disposing of the device, its batteries and accumulators, and its electrical and electronic accessories. According to the rules, this equipment must be disposed of separately at the end of its service life. Do not dispose of the device, its batteries and accumulators, or its electrical and electronic accessories together with unsorted municipal waste, as this will harm the environment. To dispose of this equipment, it must be returned to the point of sale or turned in to a local recycling facility. You should contact your local household waste disposal service for details. The warranty period and service life shall be 2 years as from the date of purchase of the device. ASBISc reserves the right to modify the device and to make edits and changes to this document without prior notice to users. The warranty period and service life shall be 2 years as from the date of purchase of the device. ASBISc reserves the right to modify the device and to make edits and changes to this document without prior notice to users. The warranty period and service life shall be 2 years as from the date of purchase of the device. Manufacturer: ASBISc Enterprises PLC, Iapetou, 1, Agios Athanasios, 4101 Limassol, Cyprus. Made in China. For current information and details on the device description and specification, as well as connection process, certificates, warranty and quality issues, see relevant Installation and Operation Manuals available for downloading at aeno.com/documents. All trademarks and names herein are the property of their respective owners
References
- Home appliances AENO - Smart home appliances on the official website of the manufacturer AENO in Europe
- Documents | AENO in Europe
- ASBIS – IT Distributor