Good Earth Lighting SE1291-BP2-02LF0-G 180-Degree 2-Head LED Motion Instruction Manual

June 3, 2024
Good Earth Lighting

Good Earth Lighting logo

SE1291-BP2-02LF0-G 180-Degree 2-Head LED Motion
Instruction Manual

Good Earth Lighting SE1291-BP2-02LF0-G 180-Degree 2-Head LED
Motion Model :
SE1291-BP2-02LFO-G
SE1291-WH3-02LFO-G

What’s in the Box

Good Earth Lighting SE1291-BP2-02LF0-G 180-Degree 2-Head LED Motion -
1

Light and Sensor Controls

Good Earth Lighting SE1291-BP2-02LF0-G 180-Degree 2-Head LED Motion -
2

Tools Needed

Good Earth Lighting SE1291-BP2-02LF0-G 180-Degree 2-Head LED Motion -
3

Safety Information

SHUT OFF POWER AT THE CIRCUIT BREAKER OR FUSE  PANEL BEFORE REMOVING_THE OLD FIXTURE OR  INSTALLING THE NEW ONE.
READ ENTIRE INSTALLATION PROCEDURE BEFORE YOU BEGIN!

LIGHT FIXTURE REQUIRES A 120VAC ELECTRICAL SYSTEM.
LIGHT MUST BE PROPERLY GROUNDED.
SOME REGIONAL/LOCAL CODES REQUIRE INSTALLATION BY A QUALIFIED ELECTRICIAN.
WARNING
This fixture can only be installed over a recessed electrical box OR a UL- Listed surface mount electrical box rated for wet locations. Surface mount electrical boxes require the use of the included foam gasket, to prevent water from seeping into the electrical box.
WARNING
BURN HAZARO:
Keep fixture’s lamp heads at least 2 in. from combustible material.
CAUTION!
BURN HAZARO: Allow light to cool down prior to touching.
WARNING
To avoid water damage, position light heads and sensor head in the correct position as indicated.
ATTENTION
If the power goes out, the fixture will maintain previous settings, so there is no need to go up the ladder to adjust once the power has been restored. Fixture will need 20-30 seconds to warm up once turned back on.
WARNING
Do not look directly at the LEDs for an extended period of time. They can cause eye damage.
CAUTION!
Minimum 90°C supply conductors. For fixture electrical ratings, see fixture label.
CAUTION!
Please consult a qualified electrician if you are unfamiliar with electrical installations, or methods of properly grounding an electrical fixture.
CAUTION!
Fixture will reliably operate between the temperatures of -20F to 122°F. (At temperatures above 92°F, the PIR may not detect body heat.)
WARNING
The components of this fixture are not serviceable. Attempting to alter the fixture for any reason may result in voiding the warranty and could result in creating a dangerous
situation.
ATTENTION
LEDs can be damaged by electrostatic discharge shock. To remove this hazard, touch a grounded bare metal surface to discharge yourself before installation.
FCC STATEMENT:
This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference. and (2) this device must accept any interference received, including interference that may cause undesired operation. Warning Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation, This equipment generates, uses, and can radiate radio frequency energy and, not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However there is no guarantee that the interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

  1. Reorient or relocate the receiving antenna.
  2. Increase the separation between the equipment and receiver.
  3. Connect the equipment into an outlet on a circuit different from that of the receiver,
  4. Consult the dealer or an experienced radio/TV technician for help. FCC responsible party name Good Earth Lighting Inc.
    Address. 1400 E Business Center Drive, STE 108 Mount Prospect, if IL 60056 USA. Telephone number 1-800-291-8838

Things to Consider Prior to Mounting

SELECT A LOCATION THAT ALLOWS THE SENSOR TO PERFORM AT ITS PEAK EFFICIENCY.
MINIMUM MOUNTING HEIGHT: 8 FT.
OPTIMAL MOUNTING HEIGHT: 8-10 FT.
Mounting above 10 ft. can decrease the sensor detection range.
DO NOT mount near light sources (street lights, traffic).

INFRARED PAS5VE
Good Earth Lighting SE1291-BP2-02LF0-G 180-Degree 2-Head LED Motion -
5

SENSOR ORIENTATION

FACE CONTROL PANEL TOWARD THE GROUND.

AIM THE PIR SENSOR TOWARD THE INTENDED DETECTION AREA.
THE FIXTURE USES A PASSIVE INFRARED (PIR) MOTION SENSOR AND AS SUCH DETECTS CHANGES IN INFRARED RADIATION OF WARM OBJECTS MOVING ACROSS THE DETECTION ZONES.

  • The PIR sensor can be triggered by a variety of sources including dryer vents, hot tubs, idling vehicles, etc.
  • The PIR sensor CANNOT detect motion through plexiglass, plastic, or glass barriers.
  • DO NOT aim the PIR toward areas with pedestrian and motorized traffic and/or other objects that generate heat.
  • DO NOT mount near nighttime light sources (street lights, traffic). Light sources can cause the light to operate in daylight mode.

How To Wire the Light

DANGER
SHUT OFF POWER TO THE JUNCTION BOX BEFORE INSTALLING THE FIXTURE.

Good Earth Lighting SE1291-BP2-02LF0-G 180-Degree 2-Head LED Motion -
8

Attach the mounting strap to junction box

Works with most electrical boxes styles

Using two small or medium box screws, attach the mounting strap to the junction box and pull the ends of the supply wires out of the junction box.
For Surface Box Mounting ONLY:
Remove the protective liner from the gasket, align the center hole of the gasket with that of the mounting strap. and apply the gasket to the outer edge of the surface mounting box as shown.

Insert junction box wires into the electrical box connector

Good Earth Lighting SE1291-BP2-02LF0-G 180-Degree 2-Head LED Motion -
11

Insert the wires into either the top or bottom contact hole for each color.
NOTE: Ground wires are normally a green insulated or bare copper wire,
CAUTION
WIRES MUST BE FULLY INSERTED INTO THE CONTACT HOLES.
Connect the box and the fixture connector

Good Earth Lighting SE1291-BP2-02LF0-G 180-Degree 2-Head LED Motion -
12

Tuck the wires into the junction box

Attaching the Light

Fasten the mounting screw

Align the center hole of the fixture and the mounting strap. Insert the long mounting screw and fasten it until the light is secure to the junction box.
CAUTION
DO NOT PINCH WIRES WHEN TIGHTENING DOWN. DO NOT OVERTIGHTEN.

Verify light works

Restore power to the junction box and verify the wiring is correct.
IMPORTANT
Verify the light switch is in the “ON” position first. During daylight hours, it may be necessary to block the light from the sensor head by blocking the light from it by covering it with a dark towel or sock. This will enable the light to activate. Should the light still not turn on, refer to the wiring section and recheck the wire connections.
Add the plug

Good Earth Lighting SE1291-BP2-02LF0-G 180-Degree 2-Head LED Motion -
17

Insert the translucent silicone plug into the center mounting hole.
IMPORTANT
THE DIAL MUST BE ROTATED AWAY FROM THE TEST SETTING FOR THE LIGHT ACTIVATION TO WORK PROPERLY. ROTATE THE DIAL TO A POINT ANYWHERE BETWEEN THE T’ AND 10′ SETTINGS AND THE LIGHT WILL ONLY ACTIVATE DURING NIGHTTIME HOURS.

How the Controls Work

The fixture has a built-in light sensor that prevents the motion sensor or area light from activating during daylight hours. Once the power has been turned on, the fixture needs around 20 tO 30 seconds to warm up. The light will turn off after around 20 seconds, then the light will go to the Set Togo factory presets (50ft. detection range, 3 minute tight activation.)

FACTORY PRESETS

Set Togo: The security light is PRESET at the factory with the following settings:

Range: 50 feet
Minutes: 3 min. (duration)| Detection distance
Time the light stays on after detecting motion
---|---

If these settings are acceptable for your needs, you don’t need to do anything more with the Set Togo settings except to do the actual electrical installation of the fixture.
ATTENTION!
To change the factory Set Togo default settings, follow the instructions below.

Customize Settings

This fixture includes a TEST mode for customizing the settings. Switch the TIMER control knob to TEST. TEST allows the light to activate in daylight hours to change the Set Togo settings.

SECURITY LIGHT TIME SETTINGS

To change the duration the light remains on after detecting motion, rotate the “Minutes” dial to the preferred setting:
Test: ONLY use during initial set-up. “Test” allows the motion detector to work during daylight hours to fine-tune the PIR sensitivity.
1: Light will stay on for 1 minute after PIR detects motion.
2′: Light will stay on for 2 minutes after PIR detects motion.
5: Light will stay on for 5 minutes after PIR detects motion.
10′: Light will stay on for 10 minutes after PIR detects motion.
IMPORTANT
THE DIAL MUST BE ROTATED AWAY FROM THE TEST SETTING FOR THE – LIGHT ACTIVATION TO WORK PROPERLY. ROTATE THE DIAL TO A POINT ANYWHERE BETWEEN THE T’ AND 10′ SETTINGS AND THE LIGHT WILL ONLY ACTIVATE DURING NIGHTTIME HOURS.

SECURITY LIGHT SENSOR RANGE SETTINGS
To change the sensitivity of the PIR distance sensing, rotate the “Range” dial the preferred setting:
1 OFt: 1 0 feet. short range
20Ft: 20 feet, average range
50Ft: 50 feet, long range
Max.: Up to 70 feet, extra long range
Rotate the RANGE control knob to any of the marked presets: 1 D Ft. to Max. I.= 70 ft.).
When the RANGE control knob is turned to 1 D Ft., the detection zone is very tight and compact. causing the detection sensitivity to be very high. When the RANGE control knob is turned to Max., the detection zone becomes very broad, resulting in a low sensitivity.
VERIFYING RANGE SETTING
To confirm the set distance, perform a “walk-by test.” Walk straight across the sensor field at the approximate distance set on the RANGE control knob.
IF THE TEST FAILS, try adjusting the sensor head toward the detection zone.
Sensor head can be adjusted either up, down, left. or right.

Manual Override

To Switch To Manual Mode

Good Earth Lighting SE1291-BP2-02LF0-G 180-Degree 2-Head LED Motion -
22

To return to “AUTO” mode: Turn the switch to the OFF position for 10 seconds and then ON.
IMPORTANT
THE SECURITY LIGHT WILL REMAIN ON UNTIL THE INTERNAL DUSK-TO-DAWN SENSOR DETECTS THE NEXT DUSK-DAWN CYCLE. ONCE THE LIGHT IS DETECTED, IT WILL ALLOW THE MOTION SENSOR TO RETURN TO CONTROLLING THE FIXTURE THE NEXT DAY.
IMPORTANT
MANUAL OVERRIDE ALLOWS THE LIGHT TO TURN ON AT ANY TIME, BY OVERRIDING ALL SENSOR CONTROLS. IT ENABLES THE LIGHT TO ACTIVATE REGARDLESS OF THE TIME OF DAY. HOWEVER, THIS PROCESS MUST BE RESET EACH DAY AFTER DUSK TO DAWN FEATURE CYCLES THE PREVIOUS DAY’S MANUAL OVERRIDE CYCLE OFF.

Troubleshooting Guide

DANGER
Before doing any work on the fixture, shut off power supply at the circuit breaker panel to avoid electrical shock.

PROBLEM POSSIBLE CAUSE CORRECTIVE ACTION
Security light does not come on. 1. Light switch is off.

2. Fuse is blown.Circuit breaker has tripped.
3.Fixture not properly wired to J-box.
4. It is daylight.
5. Motion sensor is pointed in the wrong direction.
6. Air temperature is about the same as a person’s body temperature and the motion sensor cannot “see” the person.| 1. Turn light switch on.
2.Replace fuse. Turn the circuit breaker back on.
3. Reinstall light fixture.
4. Recheck at night.
5. Readjusts motion sensor.
6. Decrease the RANGE control setting.
Light continuously cycles ON and OFF (strobe effect).| 1. Light sensor is triggered by reflected light from the security light itself.
2. Heat is being reflected from other sources and may be triggering sensor on and off.| 1. Change the position of the light head and aim light away from the reflecting surfaces.
2. Decrease the RANGE control setting.
Light turns on during daylight hours.| 1. Light may be installed in shadows/dark area.| 1. Light is operating as it was designed. Use manual override if necessary.
Light comes on for no apparent reason.| 1. Sensor may be triggered by a small animal or passing car.
2. Hot air (dryer vent, car exhaust, etc.) may be triggering the sensor.| 1. Decrease the RANGE control setting as necessary.
2. Increase the RANGE control setting as necessary.
Light stays on continuously at night.| 1. Motion sensor may be picking up a continuous flow of warm air from an
air vent, dryer vent, or heat reflecting off a surface.
2. Manual override may be activated.| 1. Reposition the motion sensor.
2. Wait until next day for internal dusk-to-dawn sensor to detect next dusk- dawn cycle. Once light is detected, this will allow motion sensor to return to controlling the fixture.
Light flashes on for 20 seconds at a time, day or
night.| 1. The TIMER control knob is set to TEST.| 1. Set the TIMER control knob somewhere between 1 and 10.

8-Year Limited Warranty

Good Earth Lighting® – The manufacturer warrants this lighting fixture to be free from defects in materials and workmanship for a period of (8) years from the date of original purchase by the consumer. The fixture is not warrantied for use in a commercial or retail application. The warranty is limited to use in a residential environment. We will repair or replace (at our option) the unit in the original color and style if available, or in a similar color and style if the original item has been discontinued, without charge. Defective units must be properly packed and returned to the manufacturer with a letter of explanation and your original purchase receipt showing date of purchase. Call 1-800-291-8838 to obtain a return authorization number and an address where to ship your defective product.
Note: C.O.D. shipments will NOT be accepted. The liability of the manufacturer is in any case limited to replacement of the defective light fixture product. The manufacturer will not be liable for any other loss, damage, labor costs, or injury which is caused by the product. This limitation upon the liability of the manufacturer includes any loss, damage, labor costs, or injury which is (I) to person or property or otherwise; (II) incidental or consequential in nature; (Ill) based upon theories of warranty, contract, negligence, strict liability, tort, or otherwise; or (IV) directly, or indirectly related to the sale, use, or repair of the product. This warranty gives you specific rights, and you may also have other rights which vary from state to state.
REPLACEMENT PARTS LIST: Hardware Kit: ZH-SE1291F02

Good Earth Lighting logo Need Help
Please visit our website athttps://goodearthlighting.com/contact-us or call the Customer Care Center
1-800-291-8838, 8.30 a.m.-5 p.m., CST, Monday-Friday.
Good Earth Lighting 1400 East Business Center Drive, Ste. 108 Mount Prospect, IL 60056
Good Earth Lighting” is a registered trademark of Good Earth Lighting, Inc. 0 2022 Good Earth Lighting, Inc. REV08.22
Printed in Vietnam

Documents / Resources

| Good Earth Lighting SE1291-BP2-02LF0-G 180-Degree 2-Head LED Motion [pdf] Instruction Manual
SE1291-BP2-02LF0-G 180-Degree 2-Head LED Motion, SE1291-BP2-02LF0-G, 180-Degree 2-Head LED Motion, 2-Head LED Motion, LED Motion
---|---

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Good Earth Lighting User Manuals

Related Manuals