Good Earth Lighting RE1203-WHG-07LF1-G Indoor/Outdoor 7-Inch LED Bluetooth Speaker Instruction Manual
- June 5, 2024
- Good Earth Lighting
Table of Contents
Good Earth Lighting RE1203-WHG-07LF1-G Indoor/Outdoor 7-Inch LED
Bluetooth Speaker
CHARGING
Before 1st use, plug in USB wall charger (not included) & micro USB cord (included) to charge product until indicator light turns green.
BATTERY DURATION
- CONTINUOUS ON
- 3 Hour
- RECHARGE TIME
- 4. 5 Hours
Light can be plugged in for continuous use.
2 WAYS TO MOUNT
Easy Installation Command
-
Clean surface with rubbing alcohol. Rotate cover counter- clock wise and remove.
-
Remove blue liners. Insert tabs into the slots. Press strips to the back of cover. Wall side facing out.
-
Remove black liners. Press cover to surface with tab towards you. Press firmly for 30 sec.
-
To reattach light, align notches and tum clockwise.
STRIP REMOVAL
-
Never pull the strip away from the surface! Always pull along the surface.
-
Stretch each strip slowly against the surface at least 12″ to release.
RECHARGE PRODUCT
- Rotate counter-clockwise to release light from cover .
Remove Product to:
- Charge Battery.
- Use as a portable light.
IMPORTANT: Failure to follow instructions carefully may cause damage.
CAUTION: Do not hang over beds or on wall paper. Mount again with Command°
Outdoor Medium Refll Strips. Not recommended on rough Surfaces, Such as cement
board, brick or rough-sawn wood. f plan to dispose after use please locate
local recycling center @call2recycle.org Command
is trademark of 3M
FOR INDOOR/OUTDOOR USE For more product and warranty information, go to:
www.goodearthlighting.com
SCREW MOUNT INSTALLATION
-
Remove cover by rotating counter-clockwise.
-
Mark the mounting holes in the cover, drive both screws into the mounting surface.
-
To reattach light, align notches and tum clockwise.
OPERATION
PRESS THE ON/OFF BUTTON TO SELECT AUTO TIMER
-
FIRS PRESS
-
SECOND PRESS
-
THIRD PRESS
-
FOURTH PRESS
BLUETOOTH PAIRING
- Set to discovery mode by holding down Bluetooth paring button for 3 seconds, audio will note “The Bluetooth device is ready to pair. A rapidly flashing blue light will confirm device is in discovery mode.
- Select “GEL RE1203 Speaker on smart device and pair. When successfully paired, the audio will note “The Bluetooth device is connected successfully”.
- Play music and adjust volume control from smart device while paired.
- To disconnect from the smart device and temporarily disable Bluetooth discovery mode, hold down the Bluetooth paring button.
The Bluetooth• word mark and logos are registered trademarks owned by Bluetooth SIG, lnc. and any use of such marks by Good Earth Lighting, Inc” is under license. Other trademarks and trade names are those of their respective owners.
NOTE: Only one device can be connected to the Bluetooth speakers at a
time.
NOTE: Make sure the Bluetooth-enabled smart device (e.g. mobile phone,
music player or pc/laptop) and Bluetooth speakers are within syncing range (33
ft) and that the device’s Bluetooth settings are set to discovery mode
enabling devices to search and connect.
FCC Statement
This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions:
- This device may not cause harmful interference, and
- This device must accept any interference received, including interference that may cause undesired operation.
Changes or modifications not expressly approved by the party responsible for
compliance could void the user’s authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates uses and
can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
The device has been evaluated to meet general RF exposure requirement. The device can be used in portable exposure condition without restriction.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>