Good Earth Lighting GL1327-AL3-24LFC-G 2-in 1-Light Silver LED Grow Light User Manual

June 8, 2024
Good Earth Lighting

GL1327-AL3-24LFC-G 2-in 1-Light Silver LED Grow Light
User Manual

2-ft./4-ft. Adjustable Full Spectrum LED Plant Grow Light (Page 1)

GL1327-AL3-24LFC-G 2-in 1-Light Silver LED Grow Light

Good Earth Lighting GL1327-AL3-24LFC-G 2-in 1-Light Silver LED Grow Light -
Figure 1Good
Earth Lighting GL1327-AL3-24LFC-G 2-in 1-Light Silver LED Grow Light - Figure
2

READ ENTIRE INSTALLATION PROCEDURE BEFORE YOU BEGIN!

WARNINGS AND CAUTIONS

WARNING: TO AVOID ELECTRIC SHOCK, DISCONNECT POWER BEFORE INSTALLING!

WARNING: DO NOT attempt to alter the fixture. The fixture is not manufactured with parts that are serviceable or replaceable.
WARNING: BURN HAZARD! The fixture can be hot; allow cooling time prior to touching.
WARNING: DO NOT ALTER THE PLUG OR CORD. This LED light has a polarized plug (one blade is wider than the other) as a feature to reduce the risk of electric  shock. This plug will only fit in a polarized outlet one way. If the plug does not fully fit in the outlet, reverse the plug. If it still does not fit, contact a qualified electrician.  Never use a power strip unless the plug can be fully inserted.
WARNING: Products should be installed following these instructions, local electrical codes, and/or the current National Electric Code (NEC). Electrical requirements can  be found on the back of the fixture.
WARNING: DO NOT use an extension cord. ONLY use power strips with integral overcurrent protection.
WARNING: DO NOT look directly at LED light source for any extended period of time.
CAUTION: ONLY operate in areas with air temperatures ranging between -0°F to 104°F (-18°C to 40°C).
CAUTION: ONLY route and secure the cords in a manner where they will not be pinched or damaged. DO NOT hang items from cords.
CAUTION: DO NOT mount to surfaces with a thickness less than 1/4 in. DO NOT mount over sinks or stoves.
CAUTION: DO NOT USE THIS FIXTURE WITH A DIMMING CIRCUIT. This fixture is not dimmable.
Turn power off before servicing.
Indoor use only.
Suitable for damp locations.

PRE-INSTALLATION

PRE-INSTALLATION
The light’s 5-ft. cord length restricts the maximum distance from an outlet the fixture can be mounted. Select a mounting location within 5 ft. of an electrical outlet. VERIFY  THE LOCATION WORKS PRIOR TO DRILLING. There are 2 basic ways to mount the light: chain mount or flush mount. For CHAIN MOUNT WITH HOOK  SCREWS, mark 2 mounting holes, 22-1/2 in. or 45-1/2 in. apart For SURFACE MOUNT, mark 22-1/4 in. or 45 in. apart. ONLY instructions for installing to a wood joist/stud or drywall are addressed here.

CHAIN MOUNT:
GL1327-AL3-24LFC-G: Mount hardware 22-1/2 in. apart
GL1327-AL3-46LFC-G: Mount hardware 45-1/2 in. apart
22-1/2 in. or 45-1/2 in. Good Earth Lighting GL1327-AL3-24LFC-G 2-in 1-Light
Silver LED Grow Light - Figure 3

1A
WOOD INSTALLATION: Using a 1/16-in. drill bit, drill the 2 pilot holes where either the hook screws or wood screws (C/D) will be installed. Insert the hook screws or  wood screws into the pilot holes. Tighten the screws until they are securely fastened into the mounting surface.
1B
DRYWALL INSTALLATION: Use a 3/16-in. drill bit, drill out the 2 insertion holes for the wedge anchors (B). Pinch the wedge anchor tips together (toward the center).  Fully insert the folded wedge anchors into the holes until flush with the surface. Tighten the screws (C/D) into the wedge anchors until they are securely fastened into the mounting surface.

CHAIN MOUNT INSTALLATION

Good Earth Lighting GL1327-AL3-24LFC-G 2-in 1-Light Silver LED Grow Light -
Figure 4

2A Determine how high the fixture needs to be suspended. Attach the “V” hook (E) to the bottom loop of the chain (A) by fishing one end of the hook through the bottom  loop. Remove any kinks out of the chain.
Repeat on the other side.
2B Insert both ends of the “V” hook (E) through the small rectangular slots along the top side of end caps and pivot the ends through the opening.

SURFACE MOUNT INSTALLATION

Locate the keyhole slots on the top side of the endcaps. Good Earth Lighting
GL1327-AL3-24LFC-G 2-in 1-Light Silver LED Grow Light - Figure
5

  1. Adjust the screws (D), leaving 1/8-in. clearance between the mounting surface and the back of the screwhead.
  2. Lift the fixture up to the mounting screws (D) and simultaneously guide the screw heads through the large round ends of the keyhole slots. Slide the fixture until the screwheads are captured in the keyhole slots.
    NOTE: If the fixture is loose, remove it and tighten each screw 1/4 turn and reattach.

POWER CORD INSTALLATION

Good Earth Lighting GL1327-AL3-24LFC-G 2-in 1-Light Silver LED Grow Light -
Figure 6

  1. Insert the connector end of the power cord into the “power-in” port located on the end of the fixture with the slide dimmer. Make sure the plug is fully inserted into the  port.
  2. Plug fixture into an electrical outlet.

OPERATION

The instructions provided do not cover growing methods; they only provide an overview of the role the grow light plays in plant development. Results from indoor  horticulture will vary based on soil nutrients, composition, moisture, air temperature, air flow, and the species of plant(s). One, two, or all three buttons can be pressed at the  same time to produce custom settings to better meet a plant’s lighting needs.

MATCH THE PLANT’S GROWTH STAGE

| BLUE: Seedling Stage
Suggested timer setting: 16H or 20H
---|---
| WHITE: Vegetative Stage
Suggested timer setting: 16H or 20H
| RED: Flowering and Fruiting Stage
Suggested timer setting: 12H

Good Earth Lighting GL1327-AL3-24LFC-G 2-in 1-Light Silver LED Grow Light -
Figure 7

MANUAL OPERATION

Locate the auto-timer on the endcap of the light near the “power-in” port. Light can be operated independently of the auto-timer feature. Good Earth
Lighting GL1327-AL3-24LFC-G 2-in 1-Light Silver LED Grow Light - Figure
8

  1. Slide timer switch to ‘OFF’ before pressing any of the color push buttons (White, Blue, or Red). When the timer is off, turn the light on and off manually by pressing the  color push buttons.
  2. Select the color(s) that match the plant’s growth stage.
    NOTE: Any or all of the buttons can be pressed at one time.

AUTO-TIMER OPERATION

This product features a continuous 24-hour auto-timer with three different timer-settings that control the light exposure given to the plants.Good
Earth Lighting GL1327-AL3-24LFC-G 2-in 1-Light Silver LED Grow Light - Figure
9

  1. Slide the timer switch to ‘OFF’ before pressing any of the color push buttons (White, Blue, or Red). When the timer is off, turn the light on and off manually by pressing  the color push buttons.
  2. Select the color(s) that match the plant’s growth stage.
  3. Slide the timer switch to the suggested timer settings, 12H, 16H, or 20H.
    The light will turn off automatically after 12 hours, 16 hours or 20 hours.
    NOTE: The timer is on a 24-hour cycle. The light will turn on automatically the same time everyday. Do not manually turn off the light or cut the power supply. If that  happens, reset the timer function by sliding the timer switch to “OFF” and start the auto-timer steps, 1 to 3 again.

OPTIONAL: INSTALLING ADDITIONAL LIGHTS

TURN POWER OFF PRIOR TO LINKING!
Use installation steps 1-3 to install additional units. To link, plug the cord into the linking outlet of the preceding fixture.
A maximum of (5) for GL1327-AL3-24LFC-G
A maximum of (2) for GL1327-AL3-46LFC-G
Fixtures can be linked together in one run. Good Earth Lighting
GL1327-AL3-24LFC-G 2-in 1-Light Silver LED Grow Light - Figure
10

NOTE: The linking cord is designed to attach one way and only one way into the adjoining fixtures. If the plug cannot be fully inserted into the fixture, reverse the ends of  the cord and try again.

Care and Maintenance
Periodically clean the fixture and diffuser using a mild, nonabrasive cleaner and soft cloth. When cleaning the fixture, make sure the power is turned off.
Do not spray cleaner directly onto any part of the fixture or LEDs.

TROUBLESHOOTING GUIDE

The information provided on the packaging should only be used as a suggestion. No guarantees of plant health or yield are guaranteed or inferred with the use of these lights. Water, soil, fertilizers, temperature, environment, and other factors will impact plant health.

PROBLEM POSSIBLE CAUSES CORRECTIVE ACTIONS
Light does not come on. Power is shut off at light switch.

Power cord or linking cord is not properly connected. Timer switch is set to “OFF” and press color button. Timer is currently running in “OFF” hour.| Verify light switch are on and a color button has been pressed. Check cord connection.
Press a color button.
Either reset timer, or wait for cycle to conclude.
Light color does not change.| Color cannot change when auto-timer is engaged.| Change to Manual Mode: Slide timer switch to the “OFF” position and press color button(s).
Auto-Timer Mode: Slide timer switch to the “OFF” position, press the desired color button(s) and slide switch to timer setting.
Timer setting does not change.| Auto-timer setting didn’t change when changed.| Slide timer switch to the “OFF” position and make sure the desired color button(s) is pressed and slide switch to timer setting.
Linking cord cannot be inserted into either or both units being linked.| Cord is being inserted in the wrong direction.
Fixtures need to be linked with the power connector the same position/direction (power-in side first).| Reverse cord and try inserting again. Plugs only fit one specific way into the fixtures.
Rotate the last fixture so the power connector is first in-line.
Fuse blows or circuit breaker trips when light is turned on.| Discontinue use immediately.| Call customer service (1-800-291-8838).

Hardware Kit: ZH-GL-VHOOKS
REPLACEMENT PARTS LIST:
Need Help?
Please visit our website at: https://goodearthlighting.com/contact-us or call the Customer Care Center 1-800-291-8838, 8:30 a.m.-5 p.m., CST, Monday-Friday.

Good Earth Lighting ® 3-YEAR LIMITED WARRANTY: The manufacturer warrants this lighting fixture to be free from defects in materials and workmanship for a period of (3) years from the date of original purchase by the consumer. The fixture is not warrantied for use in a commercial or retail application. The warranty is limited to use in a residential environment. We will repair or replace (at our option) the unit in the original color and style if available, or in a similar color and style if the original item has been discontinued, without charge. Defective units must be properly packed and returned to the manufacturer with a letter of explanation and your original purchase receipt showing date of purchase. Call 1-800-291-8838 to obtain a return authorization number and an address where to ship your defective product. Note: C.O.D. shipments will NOT be accepted. The liability of the manufacturer is in any case limited to replacement of the defective light fixture product. The manufacturer will not be liable for any other loss, damage, labor costs, or injury which is caused by the product. This limitation upon the liability of the manufacturer includes any loss, damage, labor costs, or injury which is (I) to person or property or otherwise; (II) incidental or consequential in nature; (III) based upon theories of warranty, contract, negligence, strict liability, tort, or otherwise; or (IV) directly, or indirectly related to the sale, use, or repair of the product. This warranty gives you specific rights, and you may also have other rights which vary from state to state.

FCC STATEMENT: This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Warning: Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that the interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: 1) Reorient or relocate the receiving antenna. 2) Increase the separation between the equipment and receiver. (3) Connect the equipment into an outlet on a circuit different from that of the receiver. (4) Consult the dealer or an experienced radio/TV technician for help. FCC responsible party name : Good Earth Lighting, Inc. Address: 1400 E Business Center Drive, STE 108, Mount Prospect IL 60056, USA Telephone number: 1-800-291-8838

Good Earth Lighting® 1400 East Business Center Drive, Ste. 108 Mount Prospect, IL 60056
Good Earth Lighting® is a registered trademark of Good Earth Lighting, Inc. © 2021 Good Earth Lighting, Inc.

References

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Good Earth Lighting User Manuals

Related Manuals