Good Earth Lighting SE1294-WHG-02LF7-G IP65 2-Head Battery-Operated LED 700-Lumen Security Light User Guide
- June 3, 2024
- Good Earth Lighting
Table of Contents
Good Earth Lighting SE1294-WHG-02LF7-G IP65 2-Head Battery-Operated LED
700-Lumen Security Light
What’s in the Box
Light and Sensor Controls
Tools Needed
Safety Information
READ ENTIRE INSTALLATION PROCEDURE BEFORE YOU BEGIN!
CAUTION!
- BURN HAZARD: Allow light to cool down prior to touching.
- Fixture will reliably operate between the temperatures of -20°F to 122°F. (At temperatures above 92°F, the passive infrared (PIR) sensor may not detect body heat.)
WARNING!
- Do not look directly at the LEDs for an extended period of time. They can cause eye damage.
- Use alkaline batteries only. Do not use carbon zinc batteries and DO NOT mix battery type.
- The components of this fixture are not serviceable.
Attempting to alter the fixture for any reason may result in voiding the warranty and could result in creating a dangerous situation.
ATTENTION
- LEDs can be damaged by electrostatic discharge shock. To remove this hazard, touch a grounded bare metal surface to discharge yourself before installation.
- Cold weather may affect the performance of the fixture. Alkaline batteries can lose voltage when temperatures are near freezing. This will affect the performance of the PIR in your fixture. The security light will perform as expected when temperatures rise.
FCC STATEMENT:
This device complies with Part 15 of the FCC rules. Operation is subject to
the following two conditions: (1) This device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
Warning: Changes or modifications to this unit not expressly approved by
the party responsible for compliance could void the user’s authority to
operate the equipment.
Note: This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to Part 15 of the FCC rules.
These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that the interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: 1) Reorient or relocate the receiving antenna. 2) Increase the separation between the equipment and receiver. 3) Connect the equipment into an outlet on a circuit different from that of the receiver. 4) Consult the dealer or an experienced radio/TV technician for help. FCC responsible party name : Good Earth Lighting Inc. Address: 1400 E Business Center Drive, STE 108 Mount Prospect, IL 60056 USA. Telephone number: 1-800-291-8838
3-Year Limited Warranty
Good Earth Lighting® – The manufacturer warrants this lighting fixture to be free from defects in materials and workmanship for a period of (3) years from the date of original purchase by the consumer. The fixture is not warrantied for use in a commercial or retail application. The warranty is limited to use in a residential environment. We will repair or replace (at our option) the unit in the original color and style if available, or in a similar color and style if the original item has been discontinued, without charge. Defective units must be properly packed and returned to the manufacturer with a letter of explanation and your original purchase receipt showing date of purchase. Call 1-800-291-8838 to obtain a return authorization number and an address where to ship your defective product. Note: C.O.D. shipments will NOT be accepted. The liability of the manufacturer is in any case limited to replacement of the defective light fixture product. The manufacturer will not be liable for any other loss, damage, labor costs, or injury which is caused by the product. This limitation upon the liability of the manufacturer includes any loss, damage, labor costs, or injury which is (I) to person or property or otherwise; (II) incidental or consequential in nature; (III) based upon theories of warranty, contract, negligence, strict liability, tort, or otherwise; or (IV) directly, or indirectly related to the sale, use, or repair of the product. This warranty gives you specific rights, and you may also have other rights which vary from state to state.
Things to Consider Prior to Mounting
SELECT A LOCATION THAT ALLOWS THE SENSOR TO PERFORM AT ITS PEAK
EFFICIENCY.
MINIMUM MOUNTING HEIGHT: 8 FT.
OPTIMAL MOUNTING HEIGHT: 8-10 FT.
Mounting above 10 ft. can decrease the sensor detection range.
DO NOT mount near light sources (street lights, traffic). DO NOT mount on the
ground.
THE FIXTURE USES A PASSIVE INFRARED (PIR) MOTION SENSOR AND AS SUCH DETECTS CHANGES IN INFRARED RADIATION OF WARM OBJECTS MOVING ACROSS THE DETECTION ZONES.
- The PIR sensor can be triggered by a variety of sources including dryer vents, hot tubs, idling vehicles, etc.
- The PIR sensor CANNOT detect motion through plexiglass, plastic, or glass barriers.
- DO NOT aim the PIR toward areas with pedestrian and motorized traffic and/or other objects that generate heat.
- DO NOT mount near nighttime light sources (street lights, traffic). Light sources can cause the light to operate in daylight mode.
How to Install/Replace the Batteries
How to Attach the Light
Line up the holes in the mounting bracket with the prepared mounting holes. Drive the screws in until the mounting plate is secure.
Finishing Up
Attach the security light to the mounting plate by positioning the security
light above the mounting plate. Slide the outer tabs on the security light
into the grooves of the mounting base until snug.
Adjusting the Light Heads
The individual light heads can be adjusted up/down and left/right to aim the
light heads in the direction desired.
Factory Presets
Set To Go: The security light is PRESET at the factory with the following
settings:
If these settings are acceptable for your needs, you don’t need to do anything more with the Set To Go settings except doing the actual installation of the fixture.
The light turns on when the motion sensor detects movement. The sensor detects motion up to 40 ft. The 180-degree coverage of the motion sensor is measured side-to-side. The sensor is more effective side-to-side, rather than motion coming from the front (in and out). The fixed timer is 20 seconds – The light will stay on for 20 seconds after motion detection (only during night hours).
How the Controls Work
ROTARY KNOB
Off: Select Off to completely switch off the device.
Auto: This is the normal Automatic motion sensing mode. The light will
stay on as long as the fixture detects motion. After the fixture no longer
senses motion, it will turn off after 20 seconds.
ES: This is energy-saving mode. When motion is detected, the light turns on at 70% brightness for 20 seconds. When the fixture no longer senses motion, it will go to 20% brightness. Then the light will turn off completely after 40 seconds.
DUSK LEARN BUTTON
The light is preset to work only after dusk. If you want the light to work at
a predetermined “dusk” time, then you need to set it using the Dusk Learn
button.
Press the Dusk Learn button once to recalibrate the dusk level to the current
light level. The motion sensor will now activate at this light level from now
on. If you want the light to work day and night (regardless of the light
level), push the Dusk Learn button while the fixture is outdoors during the
day, or hold the fixture up to a light source and push the Dusk Learn button.
Motion will turn the light on, day or night, regardless of the light level;
the red LED indicator will blink twice to let you know it has reset the dusk
level. To return to the default setting, push the Dusk Learn for around 3
seconds and the red LED indicator will blink twice to indicate that you have
returned to the default setting.
Troubleshooting Guide
REPLACEMENT PARTS LIST: Hardware Kit:ZH-SE1294F02
Please visit our website at: https://goodearthlighting.com/contact-us or call the Customer Care Center 1-800-291-8838, 8:30 a.m.-5 p.m., CST, Monday-Friday.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>