Good Earth Lighting SE1356-WH3-02LF4-G Hyper Bright LED Flood Light Instruction Manual

June 12, 2024
Good Earth Lighting

Good Earth Lighting SE1356-WH3-02LF4-G Hyper Bright LED Flood Light

Product Information

The Hyper Bright LED Flood Light is a high-performance outdoor security light. It features a reflector LED that provides a hyper bright illumination. The model numbers for this product are SE1356-WH3-02LF4-G and SE1356-BP2-02LF4-G.

Product Usage Instructions

  1. Select a location for mounting that allows the sensor to perform at its peak efficiency. The optimal mounting height is 8-10 ft, while the minimum mounting height is 8 ft.
  2. Avoid mounting the light near other light sources such as street lights or traffic lights.
  3. Ensure that the power is shut off at the circuit breaker or fuse panel before removing the old fixture or installing the new one.
  4. If using a surface mount electrical box, use the included foam gasket to prevent water seepage into the electrical box.
  5. Use the provided tools such as a step ladder, silicone, hammer, seal, and Phillips head screwdriver for installation.
  6. Follow the entire installation procedure as outlined in the manual.
  7. Adjust the light and sensor controls using the Time Duration Control Dial and Detection Range Control Dial.
  8. Ensure that the light fixture is properly grounded.
  9. Do not look directly at the LEDs for an extended period of time to avoid eye damage.
  10. If the power goes out, the fixture will maintain previous settings. Allow the fixture 20-30 seconds to warm up once turned back on.

For further assistance, visit our website at https://goodearthlighting.com /contact-us or call our Customer Care Center at 1-800-291-8838, Monday- Friday, 8:30 a.m.-5 p.m., CST.

What’s in the Box

Good-Earth-Lighting-SE1356-WH3-02LF4-G-Hyper-Bright-LED-Flood-Light-
\(1\)

Hardware Kit Contents: * Actual hardware may differ from illustration :Good-Earth-Lighting-SE1356-WH3-02LF4-G-Hyper-Bright-LED-Flood-Light-
\(2\)

Light and Sensor ControlsGood-Earth-Lighting-SE1356-WH3-02LF4-G-Hyper-
Bright-LED-Flood-Light- \(3\)

Tools NeededGood-Earth-Lighting-SE1356-WH3-02LF4-G-Hyper-Bright-LED-
Flood-Light- \(4\)

Safety Information

SHUT OFF POWER AT THE CIRCUIT BREAKER OR FUSE PANEL BEFORE REMOVING THE OLD FIXTURE OR INSTALLING THE NEW ONE.

READ ENTIRE INSTALLATION PROCEDURE BEFORE YOU BEGIN!

LIGHT FIXTURE REQUIRES A 120VAC ELECTRICAL SYSTEM.
LIGHT MUST BE PROPERLY GROUNDED. SOME REGIONAL/LOCAL CODES REQUIRE INSTALLATION BY A QUALIFIED ELECTRICIAN.

  • WARNING! This fixture can only be installed over a recessed electrical box OR a UL-listed surface mount electrical box rated for wet locations. Surface mount electrical boxes require the use of the included foam gasket to prevent water from seeping into the electrical box.
  • WARNING! BURN HAZARD: Keep fixture’s lamp head at least 2 inches from combustible material.
  • CAUTION! BURN HAZARD: Allow light to cool down prior to touching.
  • WARNING! To avoid water damage, position light head and sensor head in the correct position as indicated.
  • ATTENTION If the power goes out, the fixture will maintain previous settings, so there is no need to go up the ladder to adjust once the power has been restored.Fixture will need 20-30 seconds to warm up once turned back on.
  • WARNING! Do not look directly at the LEDs for an extended period of time. They can cause eye damage.
  • CAUTION Minimum 90°C supply conductors. For fixture electrical ratings, see fixture label.
  • CAUTION Please consult a qualified electrician if you are unfamiliar with electrical installations, or methods of properly grounding an electrical fixture.
  • CAUTION Fixture will reliably operate between the temperatures of -20°F to 122°F. (At temperatures above 92°F, the PIR may not detect body heat.)
  • WARNING! The components of this fixture are not serviceable. Attempting to alter the fixture for any reason may result in voiding the warranty and could create a dangerous situation.
  • ATTENTION LEDs can be damaged by electrostatic discharge shock. To remove this hazard, touch a grounded bare metal surface to discharge yourself before installation.

Good-Earth-Lighting-SE1356-WH3-02LF4-G-Hyper-Bright-LED-Flood-Light-
\(5\)

FCC

FCC STATEMENT: This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Warning: Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.

However, there is no guarantee that the interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

  1. Reorient or relocate the receiving antenna.
  2. Increase the separation between the equipment and receiver.
  3. Connect the equipment into an outlet on a circuit different from that of the receiver.
  4. Consult the dealer or an experienced radio/TV technician for help.

FCC responsible party name: Good Earth Lighting Inc.
Address: 1400 E Business Center Drive, Ste. 108 Mount Prospect, IL 60056 USA.
Telephone number: 1-800-291-8838

Warranty

10-Year Limited Warranty
Good Earth Lighting® – The manufacturer warrants this lighting fixture to be free from defects in materials and workmanship for a period of (10) years from the date of original purchase by the consumer. The fixture is not warrantied for use in a commercial or retail application. The warranty is limited to use in a residential environment. We will repair or replace (at our option) the unit in the original color and style if available, or in a similar color and style if the original item has been discontinued, without charge. Defective units must be properly packed and returned to the manufacturer with a letter of explanation and your original purchase receipt showing date of purchase. Call 1-800-291-8838 to obtain a return authorization number and an address where to ship your defective product. Note: C.O.D. shipments will NOT be accepted. The liability of the manufacturer is in any case limited to replacement of the defective light fixture product. The manufacturer will not be liable for any other loss, damage, labor costs, or injury which is caused by the product. This limitation upon the liability of the manufacturer includes any loss, damage, labor costs, or injury which is (I) to person or property or otherwise; (II) incidental or consequential in nature; (III) based upon theories of warranty, contract, negligence, strict liability, tort, or otherwise; or (IV) directly, or indirectly related to the sale, use, or repair of the product. This warranty gives you specific rights, and you may also have other rights which vary from state to state.

Things to Consider Prior to Mounting

SELECT A LOCATION THAT ALLOWS THE SENSOR TO PERFORM AT ITS PEAK EFFICIENCY.

  • MINIMUM MOUNTING HEIGHT: 8 FT.
  • OPTIMAL MOUNTING HEIGHT: 8-10 FT.
  • Mounting above 10 ft. can decrease the sensor detection range. DO NOT mount near light sources (street lights, traffic).

PASSIVE INFRARED (PIR) SENSOR ZONEGood-Earth-Lighting-SE1356-WH3-02LF4-G
-Hyper-Bright-LED-Flood-Light- \(7\)

  • The PIR sensor can be triggered by a variety of sources including dryer vents, hot tubs, idling vehicles, etc.
  • The PIR sensor CANNOT detect motion through plexiglass, plastic, or glass barriers.
  • DO NOT aim the PIR toward areas with pedestrian and motorized traffic and/or other objects that generate heat.
  • DO NOT mount near nighttime light sources (street lights, traffic). Light sources can cause the light to operate in daylight mode.

Mounting Preparations

Adjust the mounting arms

  1. After unpacking the light, loosen both star knobs on the mounting arms located on the back of the fixture.
    NOTE: The fixture must be mounted with the PIR controls facing towards the ground for proper PIR functioning.

The arms have position hash marks to aid in the installation for both STANDARD WALL MOUNT and STANDARD EAVE MOUNT. By aligning the hash marks (“-” and “=”), the arm will be positioned for two very different configurations. By aligning the “-” marks on the elbow joint and then on the pivot joint, the mounting arm is articulated for WALL MOUNT installation. By aligning the “=” marks on the elbow joint and then on the pivot joint, the mounting arm is articulated for EAVE MOUNT installation.
DO NOT EAVE MOUNT ON PERFORATED OR CHANNELED SOFFIT MATERIAL!

  • OPTION 1: WALL MOUNT Align the “-” marks on the elbow joint and pivot joint. Tighten both star knobs.Good-Earth-Lighting-SE1356-WH3-02LF4-G-Hyper-Bright-LED-Flood-Light- \(11\)
  • OPTION 2: EAVE MOUNT Align the “=” marks on the elbow joint and pivot joint. Tighten both star knobs.Good-Earth-Lighting-SE1356-WH3-02LF4-G-Hyper-Bright-LED-Flood-Light- \(12\)

How to Wire the Light

DANGER! SHUT OFF POWER TO THE JUNCTION BOX BEFORE INSTALLING THE FIXTURE.

Attach the wall plate to the fixture

  1. Feed the fixture wires through wall plate and thread the wall plate onto the mounting arm.
    For surface mount: Use only with an approve UL wet location surface electrical box.Good-Earth-Lighting-SE1356-WH3-02LF4-G-Hyper-Bright-LED-
Flood-Light- \(13\)
    Connect the wires using the provided wire nuts

  2. Fixture must be properly grounded! Using the provided wire nuts, connect fixture ground wire to ground wire. These wires can be either green or bare copper. Connect black supply lead with the black fixture wires and white supply lead with the white fixture wires using the wire nuts. Secure the wire nuts properly to prevent the wires from coming loose. Push connections and excess wires back into the compartment.Good-Earth-Lighting-SE1356-WH3-02LF4-G-Hyper-Bright-LED-Flood-Light- \(14\)

Attaching the Light

  1. Determine which machine screws fit the threaded holes in the J-box. Insert them through the mounting holes in the wall plate and in the threaded holes in the J-box and tighten. Tighten the machine screws until snug with the included Allen wrench.Good-Earth-Lighting-SE1356-WH3-02LF4-G-Hyper-Bright-LED-Flood-Light- \(15\)
  2. Use silicone adhesive caulking (not included) to seal the gap between the wall plate and the mounting surface to prevent water seepage into the J-box.Good-Earth-Lighting-SE1356-WH3-02LF4-G-Hyper-Bright-LED-Flood-Light- \(16\)

Light Orientation

To adjust the angle of the light, loosen the two knobs on the back of the light and position the light as preferred (up and down, or left and right). Once in position, tighten both knobs to lock the light into place.Good-
Earth-Lighting-SE1356-WH3-02LF4-G-Hyper-Bright-LED-Flood-Light-
\(17\)

Lumens and CCT OperationsGood-Earth-Lighting-SE1356-WH3-02LF4-G-Hyper-
Bright-LED-Flood-Light- \(18\)

FACTORY PRESETSGood-Earth-Lighting-SE1356-WH3-02LF4-G-Hyper-Bright-LED-
Flood-Light- \(19\)
If these settings are acceptable for your needs, you don’t need to do anything more with the SetToGo settings except to do the actual electrical installation of the fixture.
ATTENTION! To change the factory SetToGo default settings, follow the instructions below.

Customize Settings

THE FIXTURE CANNOT BE USED AS A DUSK-TO-DAWN LIGHT. THE FIXTURE HAS A BUILT-IN LIGHT SENSOR THAT PREVENTS THE MOTION SENSOR FROM ACTIVATING DURING DAYLIGHT HOURS.

MOTION TEST MODE TO SET DISTANCE
Rotate the MINUTES control knob to MOTION TEST to calibrate the fixture. The light will turn on for approximately 20 seconds. Allow the motion sensor about 2 minutes to warm up prior to conducting the “walk-by test”.

With the control knob set to MOTION TEST, do a “walk-by test” by walking in front of the motion sensor (figure at right).
As movement is detected, the light will activate. Remain still for approximately 5 seconds (when movement is no longer detected), the light will shut off. Resume walking and the light should turn on. Once out of the detection range, the light will shut off and the test is complete.

When the MINUTES control is set to MOTION TEST, the light will operate both during daylight and nighttime.

SETTING THE LIGHT DURATION TIME
Rotate the MINUTES control knob away from the MOTION TEST and set between 1 and 10. Do not rotate the MINUTES control knob back to the TEST area, or to Switch Control.

  • 1: Light will stay on for 1 minute after PIR detects motion.
  • 5: Light will stay on for 5 minutes after PIR detects motion.
  • 10: Light will stay on for 10 minutes after PIR detects motion.

SECURITY LIGHT SENSOR RANGE SETTINGS

  • 10Ft: 10 feet, short range
  • 20Ft: 20 feet, average range
  • 50Ft: 50 feet, long range
  • Max.: Up to 100 feet, extra long range

Rotate the DISTANCE control knob anywhere from “10Ft” to “MAX” (100 ft). When the DISTANCE control knob is turned to “10Ft,” the detection zone is very tight and compact, causing the detection sensitivity to be very high. The reverse is true, when the DISTANCE control knob is turned to “MAX,” it increases the detection zone exponentially. Perform a “walk-by test” by walking across the motion detection field at the approximate distance set on the DISTANCE control knob.

SWITCH CONTROL MODE
Switch Control allows the light to turn on at any time, by overriding all sensor controls, so the light comes on regardless of time of day.
NOTE: If the fixture is in Switch Control mode, the built-in light sensor functions will not work. If you want to temporarily override the dusk to dawn and motion sensor functions, then you should use the manual override directions (see below).

Manual Override

To Switch To Manual ModeGood-Earth-Lighting-SE1356-WH3-02LF4-G-Hyper-
Bright-LED-Flood-Light- \(26\)
To return to “AUTO” mode: Turn the switch to the OFF position for 10 seconds and then ON.

IMPORTANT THE SECURITY LIGHT WILL REMAIN ON UNTIL THE INTERNAL DUSK-TO- DAWN SENSOR DETECTS THE NEXT DUSK-DAWN CYCLE. ONCE THE LIGHT IS DETECTED, IT WILL ALLOW THE MOTION SENSOR TO RETURN TO CONTROLLING THE FIXTURE THE NEXT DAY.
IMPORTANT MANUAL OVERRIDE ALLOWS THE LIGHT TO TURN ON AT ANY TIME, BY OVERRIDING ALL SENSOR CONTROLS. IT ENABLES THE LIGHT TO ACTIVATE REGARDLESS OF THE TIME OF DAY. HOWEVER, THIS PROCESS MUST BE RESET EACH DAY AFTER DUSK TO DAWN FEATURE CYCLES THE PREVIOUS DAY’S MANUAL OVERRIDE CYCLE OFF.

Troubleshooting Guide

DANGER! Before doing any work on the fixture, shut off power supply at the circuit breaker panel to avoid electrical shock.

PROBLEM POSSIBLE CAUSE CORRECTIVE ACTION
Security light does not come on. 1.  Light switch is of.

2.  Fuse is blown or circuit breaker has tripped.

3.  Fixture not properly wired to junction box.

4.  Light is detected by sensor.

5.  Motion sensor is pointed in the wrong direction.

6.  Air temperature is about the same as a person’s body temperature and the PIR sensor cannot “see” the person.

| 1.  Turn light switch on.

2.  Replace fuse. Turn the circuit breaker back on.

3.  Discontinue use, call an electrician.

4.  Recheck at night.

5.  Readjust motion sensor.

6.  Decrease the DISTANCE control setting.

Light continuously cycles ON and OFF (Strobe efect).| 1.  Light sensor is triggered by reflected light from the security light itself.

2.  Heat is being reflected from other sources and may be triggering sensor on and of.

| 1.  Change the position of the light head, aim light away from the reflecting surfaces.

2.  Decrease the DISTANCE control setting.

Light turns on during daylight hours.| 1.  Light may be installed in shadows/dark area.

2.  The MINUTES control knob is set to

MOTION TEST.

| 1.  Light is operating as it was designed. Use manual override if necessary. Or set to “switch control.”

2.  Set the MINUTES control knob somewhere between 1 and 10.

Light comes on for no apparent reason.| 1.  Sensor may be triggered by a small animal or passing car.

2.  Hot air (dryer vent, car exhaust, etc.) may be triggering the sensor.

| 1.  Decrease the DISTANCE control setting as necessary.

2.  Increase the DISTANCE control setting as necessary.

Light stays on continuously at night.| 1.  Motion sensor may be picking up a continuous flow of warm air from an air vent, dryer vent, or heat reflecting of a surface.

2.  Interference generated from transformers, fluorescent light fixtures, or electric motors are connected to the same circuit.

| 1.  Reposition the motion sensor.

2. Install the light on a circuit without transformers, fluorescent light fixtures or electric motors connected to the circuit.

Light flashes on for 20 seconds at a time, day or night.| The MINUTES control knob is set to MOTION TEST.| Set the MINUTES control knob somewhere between 1 and 10.
 |
Light head slips down.| Star knobs are loose.| Reposition light head and tighten star knobs.
Light output is to bright or to low.| Brightness button was pressed to many times.| Press the low/high beam control button once to change the high/low beam.
Light output is too warm,neutral,cool.| Press white light selection button to desired light temp.| Press white light selection button to change to a warmer, more neutral or cooler white light selection.

REPLACEMENT PARTS LIST: Hardware Kit: ZH-SE1356-F01-WH3, ZH- SE1356-F01-BP2

Need Help? Please visit our website at: https://goodearthlighting.com /contact-us or call the Customer Care Center 1-800-291-8838, 8:30 a.m.-5 p.m., CST, Monday-Friday.
Good Earth Lighting® 1400 East Business Center Drive, Ste. 108 Mount Prospect, IL 60056
Good Earth Lighting® is a registered trademark of Good Earth Lighting, Inc. © 2023 Good Earth Lighting, Inc. REV 3.23

References

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Good Earth Lighting User Manuals

Related Manuals