i-PRO WV-QSR501 Mount Bracket Instruction Manual
- June 10, 2024
- i-PRO
Table of Contents
i-PRO WV-QSR501 Mount Bracket
Product Information
The WV-QSR501 and WV-QSR501F-W are mount brackets produced by i-PRO Co., Ltd. These products are designed to be used for mounting cameras securely on a ceiling or wall bracket. The product
dimensions are as follows:
- Main body: Approx. 480 g {1.06 lbs}
- Base guide plate and others: Approx. 140 g {0.31 lbs}
The product is compatible with the following models: QSR501F, QSR501M, QSR501F1, QSR501M1, QSR501S, and QSR501F. The product has four holes and comes with an installation manual.
Product Usage Instructions
Before using the product, please read the instructions carefully to avoid
injuries or property damage resulting from improper installation or use of
non-compatible parts.
Installation
Installation work requires technique and experience. Therefore, it is
recommended to refer the installation work to the dealer. If you have
experience in installation, follow the instructions carefully:
- Read the installation manual carefully before installing the product.
- Ensure that the bracket is suitable for your camera model.
- Install the product securely on the bracket by following the installation instructions.
- Tighten all screws and bolts to the specified torque.
- Install the safety wire to prevent the product from falling.
Precautions
It is important to observe the following precautions while using this product:
- Do not use this bracket except with suitable cameras.
- Do not rub the edges of metal parts with your hand.
- When using this product, read the precautions described in the operating instructions for the camera to be attached.
Before attempting to connect or install this product, please read these
instructions carefully and save this manual for future use.
The external appearance and other parts shown in this manual may differ from
the actual product within the scope that will not interfere with normal use
due to improvement of the product.
i-PRO Co., Ltd. assumes no responsibility for injuries or property damage resulting from failures arising out of improper installation or operation inconsistent with this documentation or through use of parts other than this product, such as locally procured parts.
“<Control No.: C****>” used in these documents should be used to search for
information on our technical information website
(https://i-pro.com/global/en/surveillance/training-support/support/technical-
information) and will guide you to the right information.
Caution:
Before attempting to connect or operate this product, please read these
instructions care-fully.
Notice:
- This product is not suitable for use in locations where children are likely to be present.
- Do not install this product in locations where ordinary persons can easily reach.
- For information about screws and other parts required for installation, refer to the corre-sponding section of this document.
Precautions
-
Do not use this bracket except with suitable cameras.
Failure to observe this may cause a drop resulting in injury or accidents. -
Refer installation work to the dealer.
Installation work requires technique and experience.
Failure to observe this may cause fire, electric shock, injury, or damage to the product. Be sure to consult the dealer. -
Install the product securely on the bracket by following the installation instructions.
Failure to observe this may cause injury or accidents. -
The screws and bolts must be tightened to the specified torque.
Failure to observe this may cause a drop resulting in injury or accidents. -
The measures of protection against a fall of this product shall be taken.
QSR501F QSR501M QSR501F1 QSR501M1
Failure to observe this may cause a drop resulting in injury or accidents.
Be sure to install the safety wire. -
Do not rub the edges of metal parts with your hand.
Failure to observe this may cause injury.
When using this product, also read the “Precautions” described in the operating instructions for the camera to be attached.
About notations
| Connection part specifications of this product| Mount bracket
corresponding with this product
---|---|---
QSR501| 4 holes| WV-QCL501, WV-QWL501
QSR501S| WV-QCL501S, WV-QWL501S
QSR501F| Female screw (ISO) 40A, Rp 1-1/2, 11crest depth 25.4 mm {1
inch} (parallel thread)| Locally procured
40A, R 1-1/2, 11crest
length 25.4 mm {1 inch} or more
(taper pipe thread)
QSR501F1| Female screw (ANSI)
40A, NPSC 1-1/2, 11.5 crest
depth 25.4 mm {1 inch}
(parallel thread)
| Locally procured
40A, NPT 1-1/2, 11.5 crest
length 25.4 mm {1 inch} or more
(taper pipe thread)
QSR501M| Male screw (ISO)
40A, R 1-1/2, 11 crest length 25.4 mm {1 inch} (taper pipe thread)
| Locally procured
40A, Rp 1-1/2, 11 crest
depth 25.4 mm {1 inch} or more
(parallel thread)
QSR501M1| Male screw (ANSI)
40A, NPT 1-1/2, 11.5 crest
length 25.4 mm {1 inch}
(taper pipe thread)
| Locally procured
40A, NPSC 1-1/2, 11.5 crest
depth 25.4 mm {1 inch} or more
(parallel thread)
Preface
This product is a mount bracket for a camera. Use this product when connecting
a camera to a ceiling mount bracket, wall mount bracket or a locally procured
bracket.
The latest information about the supported cameras
The model number is abbreviated in some descriptions in this manual.
Specifications
| Ambient operating temperature: | –50 °C to +60 °C {–58 °F to +140 °F} |
|---|---|
| Dimensions: | Maximum diameter: ø176 mm {6-15/16 inches} Height: 131 mm {5-5/32 |
inches}
(When base guide plate and other components installed: Height 135.5 mm {5-11/32 inches})
Mass:| Main body: Approx. 480 g {1.06 lbs}
Base guide plate and others: Approx. 140 g {0.31 lbs}
QSR501 QSR501F QSR501M QSR501F1 QSR501M1
Finish:| Main body: Aluminum die cast,
QSR501 QSR501F QSR501M QSR501F1 QSR501M1
i-PRO white/black
QSR501S Heavy salt damage prevention coating, i-PRO white
Precautions for installation
-
In order to prevent injury, this product must be securely mounted to a bracket according to Installation Guide.
-
Mounting method for this product
This product is designed to be used as a pendant mount camera. If it is mounted on a desktop or at a slant, the camera may not work correctly and its lifetime may be shortened. -
Installation place QSR501S
Salt damage prevention is applied to this product. However, it is not completely anti-corrosive. Therefore, consider a place for installation where direct splash of seawater can be avoided. Especially when installing this product in a seashore area or a place where a snow-melting agent is applied, and also where rainwater is avoided, it is recommended to regularly clean and rinse off salt with water. In case of installing this product in a seashore area, regularly check the status of equipment. (Replace the parts as required.) -
Make sure to remove this product if it will no longer be used.
Standard Accessories
- Operating Instructions (this document)……………………………………………………………………………. 1 pc.
- Inner cover………………………………………………………………………………………………………………… 1 pc.
- Screw A (Fixing screw for the inner cover: M3 x 8 mm {5/16 inches})………………………………….4 pcs. (of them, 1 for spare)
- Base guide plate*1………………………………………………………………………………………………………. 1 pc.
- Screw B*1 (Fixing screw for the base guide plate: M4 x 8 mm {5/16 inches})………………………..5 pcs. (of them, 1 for spare)
- Screw C (Fixing screw for attachment plate: M4 x 8 mm {5/16 inches})……………………………….5 pcs. (of them, 1 for spare)
Base guide plate and screw B are not included in QSR501S .
Use the base guide plate when fixing the camera by utilizing the installation
dimension of 83.5 mm x 64 mm {3-9/32 inches x 2-17/32 inches}.
When fixing the camera after installing this bracket, use the screw that is
yet unused among screw B and screw C.
Other items that are needed (not included)
Common
-
Screws to fix a locally procured bracket on the installation surface
QSR501 QSR501S -
5 mm (distance between two parallel sides of a hexagon) hex wrench
QSR501F QSR501M QSR501F1 QSR501M1 -
Sealant for waterproof treatment
-
Safety wire
-
Safety wire fixing screw
-
Use a screw having a pull-out strength that is enough to hold the sum of weight of the camera, this bracket, locally procured bracket, wire and cables.
- Select a fixing method in accordance with the installation place surface for a part where the safety wire is to be fixed.
- Use the dedicated tool when processing the wire.
- Maximum weight of locally procured bracket: 5 kg {11 lbs}
INSTALLATION
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>