SW-MOTECH BC.SYS.07.649.30001 B SysBag Bag System Instruction Manual

SW-MOTECH BC.SYS.07.649.30001 B SysBag Bag System

ANBAUANLEITUNG / MOUNTING INSTRUCTIONS

SLC side carrier

Thank you for choosing this premium product from SW-MOTECH. Please visit our webshop for additional information, such as application charts and PDF mounting instructions. Any other documents that may be required (e.g. ABE certifications), are also available for download at our webshop.
Installation and / or maintenance of this product require good technical understanding! For your own safety SW-MOTECH recommends having installation and / or servicing carried out by a specialist workshop! SW-MOTECH assumes no liability for damage caused by improper installation and/ or maintenance work!
Carefully follow all the directions given in the mounting instructions and pay attention to all relevant information in the vehicle manual during assembly. Nonconformance can lead to vehicle damage or even endanger the driver! These mounting instructions are written based on our current state of knowledge. Legal requirements for accuracy do not exist.
This product was developed for vehicles in their factory setting. Compatibility with original accessory parts or other manufacturers” accessory parts is not guaranteed. Furthermore, BEFORE installing this product, make sure that all moving parts (e.g. the chain) are in the original state of maintenance. Installed accessories can change the driving behaviour and/ or stability of your vehicle.

GENERAL INFORMATION
Observe the country-specific regulations concerning vehicle registration / operation as well as TUY regulations if applicable. If required, register installed parts in the vehicle documents through an appropriate inspection authority.

PREPARATION : Read the mounting instructions carefully and make sure that all items of the parts list are included. Make sure that your vehicle is parked safely and cannot fall over. Turn off the engine and remove the ignition key. Let the motor / exhaust cool off if necessary. Disconnect the vehicle battery when working on the electrical system. Use appropriate tools. Have another person to help you.

MOUNTING : All parts and connections removed from the vehicle must be reinstalled in accordance with the vehicle manufacturers· specifications or replaced by parts delivered by SW-MOTECH. Secure all threads, unless otherwise specified, with medium-strength liquid thread locker.
Torque specifications undefined by SW-MOTE CH must be obtained from the vehicle manufacturer or by a specialist workshop!

FUNCTION CHECK : After installation make sure that all parts and connections previously removed are properly replaced. Also make sure that no moving parts are obstructed and no function of the vehicle is hindered in any way. Cables and hoses must not rub and/ or be pinched. Before starting to ride, perform a comprehensive check of all functions. After the first 50 km and then at regular intervals, check the tightening torque of all screw connections and the proper fit of the product.

PARTS LIST

MOUNTING

• NOTE: The mounting steps [1] to [5] show the mounting of the left side carrier.
  Mount the right side carrier in the same way as on the left side of the vehicle.
  Remove the seat.
  Then remove the passenger grip and the shown tail fairing from the vehicle .

• Attach the parts (2) to (5) to the side carrier (1 ), as shown in the drawing. ATTENTION: Use liquid thread locker!
  Tighten the screws as specified.

• Attach the side carrier [1 l with the passenger grip to the vehicle, as shown in the drawing.
  ATTENTION: Use liquid thread locker!
  Do not fully tighten the screws yet.

• NOTE: For mounting on both sides only the cover plate (10], the screws (11] and the washers (12] of one side carrier are required; the spacers (13] are not required.
  Attach the side carrier [1 l with the cover plate [10) to the vehicle, as shown in the drawing.
  ATTENTION: Use liquid thread locker!
  Once all parts are evenly positioned without excess tension, tighten the screws (6), (7) and (11) with the manufacturers’ specified torque.

MOUNTING INSTRUCTIONS

Adapter plate for SysBag 15

Thank you for choosing this premium product from SW-MOTECH. Please visit our webshop for additional information, such as application charts and PDF mounting instructions. Any other documents that may be required (e.g. ABE certifications), are also available for download at our webshop.
Installation and/or maintenance of this product require good technical understanding! For your own safety SW-MOTECH recommends having installation and/or servicing carried out by a specialist workshop! SW-MOTECH assumes no liability for damage caused by improper installation and/or maintenance work!
Carefully follow all the directions given in the mounting instructions and pay attention to all relevant information in the vehicle manual during assembly. Nonconformance can lead to vehicle damage or even endanger the driver! These mounting instructions are written based on our current state of knowledge. Legal requirements for accuracy do not exist.
This product was developed for vehicles in their factory setting. Compatibility with original accessory parts or other manufacturers” accessory parts is not guaranteed. Furthermore, BEFORE installing this product, make sure that all moving parts (e.g. the chain) are in the original state of maintenance. Installed accessories can change the driving behaviour and/or stability of your vehicle.

GENERAL INFORMATION
Observe the country-specific regulations concerning vehicle registration/ operation as well as TUV regulations if applicable. If required, register installed parts in the vehicle documents through an appropriate inspection authority.
PREPARATION: Read the mounting instructions carefully and make sure that all items of the parts list are included. Make sure that your vehicle is parked safely and cannot fall over. Turn off the engine and remove the ignition key. Let the motor/exhaust cool off if necessary. Disconnect the vehicle battery when working on the electrical system. Use appropriate tools. Have another person to help you.

MOUNTING: All parts and connections removed from the vehicle must be reinstalled in accordance with the vehicle manufacturers· specifications or replaced by parts delivered by SW-MOTECH. Secure all threads, unless otherwise specified, with medium-strength liquid thread locker.
Torque specifications undefined by SW-MOTE CH must be obtained from the vehicle manufacturer or by a specialist workshop!

FUNCTION CHECK : After installation make sure that all parts and connections previously removed are properly replaced. Also make sure that no moving parts are obstructed and no function of the vehicle is hindered in any way. Cables and hoses must not rub and/or be pinched. Before starting to ride, perform a comprehensive check of all functions. After the first 50 km and then at regular intervals, check the tightening torque of all screw connections and the proper fit of the product. part list

MOUNTING

NOTE: The mounting steps [1] to [3] show the mounting of the left adapter plate. Mount the right adapter plate in the same way as on the left side. Mount the shown parts on the other side of the adapter plate. ATTENTION: Pay attention to the markings (parallelogram or triangle) which define the respective mounting side (see detail drawing on the top right side)!
Attach the parts (2) to (5] to the adapter plate [1). as shown in the drawing.
Tighten the screws as specified in the parts list.

Configuration B for:
Adapter plate for STEEL-RACK and ADVENTURE-RACK
ATTENTION : Make sure that the locking mechanism (2) and the lock bolt of the adapter kit for Sys Bag 15/30 are mounted opposite to each other!
Attach the parts (2] to (5] to the adapter plate (1). as shown in the drawing.
Tighten the screws as specified in the parts list.

Configuration C for:
SLC side carrier and Adapter plate for STREET-RACK
NOTE: The mounting steps [1] to [3] show the mounting of the left adapter plate. Mount the right adapter plate in the same way as on the left side. Mount the shown parts on the other side of the adapter plate. ATTENTION: Pay attention to the markings [parallelogram or triangle) which define the respective mounting side [see detail drawing on the top right side)!
Attach the parts [2) to [5) to the adapter plate [1 l, as shown in the :¥- drawing.

Attach the adapter plate [1) to your SysBag 15, as shown in the drawing. Pay attention to the alignment of the lid of the Sys Bag 15.
ATTENTION: Use medium-strength liquid thread locker!
Tighten the screws as specified in the parts list.

Attach the adapter plate (1) to your SysBag 15, as shown in the drawing. Pay attention to the alignment of the lid of the Sys Bag 15 .
ATTENTION: Use medium-strength liquid thread locker!
Tighten the screws as specified in the parts list.

Place the locking openings of the locking mechanism (2) and the locking adapter (3) onto the guide bolts of the adapter kit for SysBag 15/30 (sold separately). Then press the SysBag 15 onto the guide bolts, until it properly rests on your
SW-MOTECH carrier system.
ATTENTION: Make sure that all guide bolts of the adapter kit for SysBag 15/30 engage at the same time! Pay attention to the clearly audible snap sound of the locking mechanism and that the red marking under the slider is not visible!
To release press the slider downward or pull the release cord.

MOUNTING INSTRUCTIONS

Sys Bag 10 / 15 / 30

Thank you for choosing this premium product from SW-MOTECH. Please visit our webshop for additional information, such as application charts and PDF mounting instructions. Any other documents that may be required (e.g. ABE certifications), are also available for download at our webshop.
Installation and/or maintenance of this product require good technical understanding! For your own safety SW-MOTECH recommends having installation and/or servicing carried out by a specialist workshop! SW-MOTECH assumes no liability for damage caused by improper installation and/or maintenance work!
Carefully follow all the directions given in the mounting instructions and pay attention to all relevant information in the vehicle manual during assembly. Nonconformance can lead to vehicle damage or even endanger the driver! These mounting instructions are written based on our current state of knowledge. Legal requirements for accuracy do not exist.
This product was developed for vehicles in their factory setting. Compatibility with original accessory parts or other manufacturers” accessory parts is not guaranteed. Furthermore, BEFORE installing this product, make sure that all moving parts (e.g. the chain) are in the original state of maintenance. Installed accessories can change the driving behaviour and/or stability of your vehicle.

GENERAL INFORMATION
Observe the country-specific regulations concerning vehicle registration/ operation as well as TUV regulations if applicable. If required, register installed parts in the vehicle documents through an appropriate inspection authority.
PREPARATION: Read the mounting instructions carefully and make sure that all items of the parts list are included. Make sure that your vehicle is parked safely and cannot fall over. Turn off the engine and remove the ignition key. Let the motor/exhaust cool off if necessary. Disconnect the vehicle battery when working on the electrical system. Use appropriate tools. Have another person to help you.

FUNCTION CHECK: This is a universal product. For this reason make sure BEFORE the first use, that the product can be fixed properly and used without problems with your vehicle type. After fixation also make sure that no moving parts are obstructed and the function of the vehicle is not hindered in any way. Lamps as taillight and turn signals must not be limited in their function. Cables and hoses must not rub and/or be pinched. Before starting to ride, perform a comprehensive check of all functions.

PRODUCT SPECIFIC INFORMATION
ATTENTION: Riding with this product may affect the motorcycles driving and braking performance!
ATTENTION: Depending on the location of fixation, cornering and ground clearance can be reduced by using this product!
ATTENTION: Before riding and at each stop (every 200 km) check proper fixation of the product!

PARTS LIST

FASTENING

FASTENING TO THE VEHICLE
ATTENTION: Before fastening your SysBag (1) to the vehicle, the rear eyelets must be closed with the included rubber plugs (4) (shown in the detail drawing at the top)!
ATTENTION: Protect sensitive surfaces in the area of the SysBag (1) and the fastening straps with the adhesive protection foil (5) from scratches!
Place your SysBag (1) in the rear area of your vehicle (e.g. passenger seat, luggage rack etc.I.
On both sides entangle TWO loop straps (6) to appropriate and reliable attachment points in the rear area of the vehicle (e.g. luggage hook etc.I.
TIP: SW-MOTECH recommends the mounting with the lashing eyes (2) (only SysBag 10 and 15). Attach the lashing eyes (2) with the original screws behind your license plate.
Then entangle on both sides TWO loop straps (6) to appropriate and reliable attachment points of the vehicle (e.g. vehicles frame, footrest mounts etc.].
Attach the hook buckles of the loop straps (6) on both sides to the marked loops of the SysBag (11, as shown in the lower drawing. Tighten all loop straps until the Sys Bag (1 I is centered and securely fastened to the vehicle.
Secure the overlength of the loop straps (6) with the rubber loops.

LISTENING TO THE SYSBAG 15 (Optional)

Attach your SysBag 15 (A) to the vehicle as described in step [1].
Loosen the upper two straps of the vehicle-mounted SysBag 15 (A). Attach the hook buckles of the two straps to the shown loops (behind the lid) of the Sys Bag 10 or 15 (B).
On both sides, loosen the upper straps on each side of the SysBag 10/15 (Bl.
Attach the hook buckles of the two straps to the loops shown on the attached SysBag 15 (A).
After ALL FOUR hook buckles are properly hooked, tighten the straps until the Sys Bag 10/15 (Bl is firmly attached on the SysBag 15 (A). Secure the overlength of the straps (4) with the velcro loops against flapping.
FUNCTION CHECK
(MUST BE OBSERVED)
ATTENTION: All components of the SysBag must not contact any hot or moving parts of the vehicle. All parts should also remain 15 cm away from hot parts of the vehicle and remain clear of the exhaust stream. For this reason compress the suspension fully several times with your vehicle stationary.

BELADUNG und PFLEGE / LOADING and CARE

LOADING
ATTENTION: Pay attention to keep items and electronic devices that can be damaged by magnetic fields away from the magnets sewn in the lid of the SysBag [1)!
ATTENTION: Never store pointy or sharp-edged objects, which could cause injury to persons or damage to the vehicle/side case!
PFLEGE
Verwenden Sie zur Reinigung NUR eine weiche TextilbUrste, ein Tuch oder Schwa mm und warme Seifenlauge! Spulen Sie anschlie­llend mit klarem Wasser nach.
Verwenden Sie KEINE scharfen Reinigungsmittel, raue Putzutensi­lien oder einen Hochdruckreiniger! Reinigen Sie die SysBag unbedingt nach Winterfahrten, um Schaden durch das Salz zu vermeiden.
CARE
For cleaning use ONLY a soft textile brush, cloth or sponge and warm soapy water! Rinse with clean water.
Do NOT use strong cleaning agents, rough cleaning tools or high pressure washer!
Clean the SysBag after riding in salty conditions, to avoid damage from salt.

COMBINATIONS

The SysBag line has only three bags but offers over 20 mounting options and combination possibilities. The bags can be lashed to the tail end or at the side, as described in the mounting instructions, or mounted to the carrier/ rack with a quick-release fastener. On this page you will find some mounting examples.
Vehicle-specific solutions, SysBag sets and adapter plates for SW-MOTECH carriers/ racks can be found in our webshop.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>