SOMOGYI FLL PIR 20 LED Spotlight Instruction Manual

SOMOGYI FLL PIR 20 LED Spotlight Instruction

LED FLOODLIGHT WITH MOTION DETECTOR

Before use of the product, please read this instruction manual and keep it for future reference. The original document was prepared in Hungarian language. This weatherproof LED floodlight is especially suited for the illumination of buildings and courtyards. The adjustable base allows mounting on a vertical surface.

COMMISSIONING
Attention! The commissioning must be carried out by a specialist in compliance with the applicable safety and contact protection regulations

Follow the steps in Figure 1

1. Caution! Before installing and connecting the luminaire, disconnect the power supply!
2. Check that the product, including the PIR motion sensor, has not been damaged during transport. Only mount and install the product on the wall if it is undamaged!
3. Use screws and dowels to mount the luminaire on a wall with a suitable load-bearing capacity, at least 1.8 m above floor level and up to 5 m high. Choose a location that provides IP65 protection for the floodlight.
4. Remove the cover of the junction box by removing the 4 screws. Unscrew the outer plastic nut from the cable gland. Thread the plastic nut onto the wire and feed the wire through the gland into the junction box.
   Connect the power cables according to the terminal block markings

5. Screw the plastic nut tightly back onto the gland. Screw the gland cover back on so that the silicone gasket is in place. Tighten the 4 screws. Adjust the angle and direction of the floodlight and the PIR motion sensor.
6. You can now reconnect the circuit by switching on the circuit breaker.

THE MOTION DETECTOR

The floodlight is turned on by the built-in motion sensor and operates only for the preset time. If there is continuous movement in the observed space, the switch-off delay time starts from the end of the movement. This time interval can be adjusted from 10 seconds to 8 minutes with the TIME potentiometer. An additional feature is the possibility of switching on depending on the ambient light intensity. The LUX knob is used to set the brightness level below which (3-20.000 LUX) the device will switch on when motion is detected. This way the lamp does not operate unnecessarily. The detection distance can be adjusted with the SENS button, from about 2 to 8 metres

The diagrams showing the detection range will help you to choose the location for installation. (Figure 2)

Things to know:

• If the difference between the temperature of the person moving and the ambient temperature is small (e.g. in hot summer weather), the range of 8 m may be reduced by up to half.
• Occasional false activation may be caused by hot air flow or a gust of wind, or by a car passing nearby (hot engine) or similar phenomenon.
• If the light sensor of the lamp is partially or completely shielded (e.g. under a roof, under a tree), it may be switched on during daylight hours when moving.
• It is desirable to aim for a clearly visible detection zone.

CLEANING, MAINTENANCE

To ensure the optimal operation of the luminaire, you need to clean it on a monthly basis at least, or when it becomes dirty.

1. Before cleaning, disconnect the luminaire from power supply.
2. Let the luminaire cool down (min. 30 minutes)
3. Clean the outside of the luminaire with a slightly damp cloth. Do not use aggressive cleaning agents! Do not let water leak inside the luminaire or spill on electrical components.

PROTECTIVE SCREEN

If the protective screen is cracked or broken, do not use the product any longer. The protective screen is not replaceable, so if it is damaged, the product must be destroyed

TROUBLESHOOTING

appliance and the power supply.
Check that the light sensitivity setting is correct.

Sensitivity is low.

| Check that the motion sensor window is not blocked or needs cleaning.
The ambient temperature may be too high.
Check whether there is an inductive signal source in the detection area of the motion sensor (e.g. electric motor).
Check the installation height.
Check that the direction of the movement to be detected is correct.

The motion sensor does not switch off the device.

| Check if there is a continuous infrared signal source in the detection area.
---|---
Check whether the delay time is set to maximum.
Check that the mains voltage is 230 V~ / 50 Hz.
Check that the temperature does not change frequently near the sensor (e.g. due to air conditioning, radiator).

WARNINGS

• Make sure that the product was not damaged during shipping.
• Always disconnect the power supply before commissioning, repair or cleaning!
• The product must be installed and repaired by qualified personnel only, in compliance with the applicable safety regulations.
• Mount it on a surface with a suitable load-bearing capacity, at least 1.8 m above floor level and up to 5 m high.
• The luminaire cannot be installed in loops.
• The luminaire must only be connected to an installed cable!
• The wire must be of H05RN-F type, and 3 x min. 1.0 mm2 cross-section!
• Always use the lamp with its protective shield!
• The protective screen is not replaceable, so if it is damaged, the product must be destroyed!
• Do not cover up the floodlight!
• The light source in the luminaire is non-replaceable. At the end of the service life of the light source, the entire luminaire must be disposed.

Do not stare into the light of the LED

The lamp shade can not be replaced, so in case of its damage the entire product must be discarded

Please maintain the required distance from the illuminated surface (and should be 0,5 m)!

Risk of electric shock! Do not attempt to disassemble of modify the unit or its accessories. In case any part is damaged, immediately power off the unit and seek the assistance of a specialist

DISPOSAL
Waste equipment must be collected and disposed separately from household waste because it may contain components hazardous to the environment or health. Used or waste equipment may be dropped off free of charge at the point of sale, or at any distributor which sells equipment of identical nature and function. Dispose of product at a facility specializing in the collection of electronic waste. By doing so, you will protect the environment as well as the health of others and yourself. If you have any questions, contact the local waste management organization. We shall undertake the tasks pertinent to the manufacturer as prescribed in the relevant regulations and shall bear any associated costs arising.

TECHNICAL DATA

• This product contains an F energy efficiency class light source.
• power supply: 220-240 V~, 50/60 Hz
• colour temperature: 4000 K
• Meaning of class IP65: Protected against dust penetration. Protection against water jets (from any direction)
• operating temperature: -20 to +40°C

MOTION DETECTOR

• detection angle: 140° in fan shape
• detection distance: approx. 2-8 m (<24 °C)
• operating time: 10 ± 5 sec. – 8 ± 2 min.
• light sensitivity: 3-20,000 LUX

Distribuitor: S.C. SOMOGYI ELEKTRONIC S.R.L. J12/2014/13.06.2006 C.U.I.: RO 18761195 • Cluj-Napoca, judeţul Cluj, România, Str. Prof. Dr. Gheorghe Marinescu, nr. 2, Cod poştal: 400337 • Tel.: +40 264 406 488, Fax: +40 264 406 489 • www.somogyi.ro Uvoznik za SRB: ELEMENTA d.o.o.Jovana Mikića 56, 24000 Subotica, Srbija • Tel:+381(0)24 686 270 • www.elementa.rs     Zemlja uvoza: Mađarska • Zemlja porekla: Kina • Proizvođač: Somogyi Elektronic Kft.

References

• Zed d.o.o.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>