AMP Remote User Manual

Remote User Manual

Fields of Application

Specifications

Safety Instructions

1. Do not expose motor to humid, damp, or extreme temperature conditions.
2. Do not drill into motor.
3. Do not cut the antenna. Keep it clear from metal objects.
4. Do not allow children to play with this device.
5. If the power cable or connector is damaged, do not use.
6. Ensure the correct crown and drive adaptor are used.
7. Ensure the power cable and aerial is clear and protected from moving parts.
8. Cable routed through walls should be properly isolated.
9. Motor is to be mounted in horizontal position only.
10. Before installation, remove unnecessary cords and disable equipment not needed for powered operation.
11. Installation and programming should be performed by a qualified professional. Use or modification outside the scope of these instructions may void warranty.

Button Instructions

Replace/Install CR2450 Battery

a. Gently insert the included ejector tool into the small pinhole opening and apply a small amount of pressure to the cover and slide the cover off.
b. Install battery (CR2450) with positive (+) side facing up.
c. Gently slide the cover back on until a “click” sound is heard.

Advanced Setting – Disable Limit Setting

a. Remove the cover from the backside of remote, the lock switch is in the right corner.
b. Move the switch to the “Lock” position to disable the following commands, remote will show “ L” (lock):
– Change Motor Direction
– Setting the Upper and Lower Limit
– Adjust Limit
– Roller Mode or Sheer Mode
c. Move the switch to “Unlock” position to assess all remote functions, remote will show “U” (unlock).

*This advanced feature is intended to be used after all shade programming is completed. User Mode will prevent accidental or unintended changing of limits.

Channel Options

Select A Channel
a. Press “<” button on the remote to select a lower channel.
b. Press “>” button on the remote to select a higher channel.

Hide Unused Channels
a. Press and Hold (about 3 sec) “<” and “>” buttons simultaneously until remote control displays “C” (channel).
b. Press “<” or “>” button to select required quantity of channel (between 1 to 15).
c. Press “Stop” button to confirm selection (the example shows a 5-channel selection). The LED will display “o” (OK) once to confirm selection.

• AMPCEL and AMPTILT motors DO NOT BEEP.

Essential Settings
The steps in factory mode must be completed to ensure proper operation.

1. Pair / Unpair Remote Control

a. Press “P1” button (about 2 sec) on the motor head until motor jog x1 and beep x1.
b. In the next 10 secs, press and hold “Stop” button on the remote control until motor jog x2 and beep x3.

• Repeat the same procedure to unpair remote control.

2. Change Motor Direction (if necessary)

Press “Up” or “Down” button to check if the shade moves in the desired direction. If you need to reverse the direction, press and hold (about 2 sec) “Up” and “Down” buttons simultaneously until motor jog x1 and beep x1.

*The operation is only valid when there are no limits. If the motor has already set the upper and lower limit, then you can only switch direction by pressing “P1” button (about 10 sec) on the motor head until motor jog x3 and beep x3.

3. Setting the Upper and Lower Limits

3.1 Set Upper Limit
a. Press “Up” button to raise the shade, then press “Stop” button when it is in the desired upper limit.
b. Press and hold (about 5 sec) “Up” and “Stop” buttons simultaneously until motor jog x2 and beep x3.

3.2 Set Lower Limit
a. Press “Down” button to lower the shade, then press “Stop” button when it is in the desired lower limit.
b. Press and hold (about 5 sec) “Down” and “Stop” buttons simultaneously until motor jog x2 and beep x3.
*If you exit the limit setting status before you finish the limit settings, the motor will take the previous existing limits.

4. Adjust Limits

4.1 Adjust the Upper Limit
a. Press and hold (about 5 sec) “Up” and “Stop” buttons simultaneously until motor jog x1 and beep x1.
b. Use “Up” button to raise the shade to the desired highest position, and use “Up” or “Down” button to do the final adjustment if necessary.
c. Press and hold (about 5 sec) “Up” and “Stop” buttons simultaneously until motor jog x2 and beep x3.

4.2 Adjust the Lower Limit
a. Press and hold (about 5 sec) “Down” and “Stop” buttons simultaneously until motor jog x1 and beep x1.
b. Use “Down” button to lower the shade to the desired lowest position, and use “Up” or “Down” button to do the final adjustment if necessary.
c. Press and hold (about 5 sec) “Down” and “Stop” buttons simultaneously until motor jog x2 and beep x3.

5. Favorite Position
5.1 Set Favorite Position
a. Use “Up” or “Down” button to move the shade to desired Favorite position.
b. Press one “P2” button on the back of remote control until motor jog x1 and beep x1.
c. Press “Stop” button until motor jog x1 and beep x1.
d. Once more, press “Stop” button until motor jog x2 and beep x3.

5.2 Send Shade to Favorite Position
Press and hold (about 2 sec) “Stop” button, motor will move to Favorite position.

5.3 Delete Favorite Position
a. Press one “P2” button until motor jog and beep x1.
b. Press “Stop” button until motor jog and beep x1.
c. Once more, press “Stop” button until motor jog x1 and long beep x1.

6. Roller Mode and Sheer Mode

6.1 Roller Shade Mode – continue movement after a short press – Default Mode
a. Press and hold (about 5 sec) “Up” and “Down” buttons simultaneously until motor jog x1.
b. Press and hold (about 2 sec) “Stop” button until motor jog x2 and beep x3.

6.2 Sheer Shade Mode – jog movement after a short press (continue movement after a long press)
a. Press and hold (about 5 sec) “Up” and “Down” buttons simultaneously until motor jog x1.
b. Press and hold (about 2 sec) “Stop” button until motor jog x1 and beep x1.

7. Add or Remove Additional Remote

7.1 Using Current Remote Control
a. On the current remote control, press one “P2” button until motor jog x1 and beep x1.
b. Once more, on the current remote control, press one “P2” button until motor jog x1 and beep x1.
c. On the New remote control, press one “P2” button until motor jog x2 and beep x3.

*Repeat the same procedure to remove additional remote control.
7.2 New Remote Control
Follow instructions under the section 1. Pair / Unpair Remote Control

8. Adjust Motor Speed

8.1 Acceleration Speed
a. Press one “P2” button until motor jog x1 and beep x1.
b. Press “Up” button until motor jog x1 and beep x1.
c. Once more, press “Up” button until motor jog x2 and beep x1.

8.2 Deceleration Speed
a. Press one “P2” button until motor jog x1 and beep x1.
b. Press “Down” button until motor jog x1 and beep x1.
c. Once more, press “Down” button until motor jog x2 and beep x1.

*If the motor has no response, it already has a Maximum or Minimum speed.

Declarations

U.S. Radio Frequency FCC Compliance
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation.
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a  particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

Any Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

ISED RSS Warning:
This device complies with Innovation, Science and Economic Development Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device.

Quick Index

Stop (hold down for 2s)
Lower Limit:  Down (hold down for 2s)  >  Down + Stop (hold down for 2s)
4 Add / Remove Favorite Position| P2  >  Stop  >  Stop
5 Roller Mode & Sheer Mode Switch| Up + Down (hold down for 5s)  >  Stop
6 Adjust Limits| Upper Limit:  Up + Stop (hold down for 5s)  >  Up or Down  > Up + Stop (hold down for 2s)
Lower Limit:  Down + Stop (hold down for 5s)  >  Up or Down  >  Down + Stop (hold down for 2s)
7 Pair / Unpair Additional Emitter| P2 (existing)  >  P2 (existing)  >  P2 (new)
8 Speed Regulation| Acceleration:  P2  >  Up  >  Up
Deceleration:  P2  >  Down  >  Down

Troubleshooting

compatible AC adaptor and check connection and positioning of solar PV panel
Insufficient charging from Solar PV Panel| Check connection and orientation of solar PV panel
Remote control battery is discharged| Replace battery
Battery is inserted incorrectly into remote control| Check battery polarity
Radio interference / shielding| Ensure remote control and the antenna on the motor are positioned away from metal objects
Receiver distance is too far from Remote Control| Move remote control to a closer position
Power failure| Check power supply to motor is connected and active
Incorrect wiring| Check that wiring is connected correctly (refer to motor installation instructions)
Motor beeps 10 times when in use| Battery voltage is low / PV (solar panel issue)| Recharge with AC adapter or check connection and positioning of solar PV panel
Cannot program a single motor (multiple motors respond)| Multiple motors are paired to the same channel.| Always reserve an individual channel for programming functions
SYSTEM BEST PRACTICE – Provide an extra 15 channel remote in your multi-motor projects that provides individual control for each motor for programming purposes
Place all other motors into sleep mode (Press “P1” button (about 6 sec) on the motor head until motor jog x2 and beep x2).

Do not dispose of in general waste.
Please recycle batteries and damaged electrical products appropriately.

Please scan QR code to see more AMP™ product information

http://ampmotorization.com/

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>