AMP Lighting AMPTILT Series Horizontal Blinds Motor Instruction Manual

AMP Lighting AMPTILT Series Horizontal Blinds Motor

Fields of Application

Tilt-Only Horizontal

Specifications

Working temperature: -10° C – +50″ C
Input Voltage: USB 5V 1 A/ USB 5V 2A Maximum Running Time: 6 minutes
The motor is suitable for motorization of venetian blinds.

Model| Rated Torque (N.m)| Rated Speed (RPM)| Rated Power (W)
---|---|---|---
AMPTILT-0.6/12| 0.6| 12| 6

Attention

Never drop, knock, drill or submerge the motor. Keep the power cable in the proper position as shown below. Read all safety instructions before installation. Incorrect installation can lead to serious injury and will void manufacturer’s liability and warranty.

Safety Instructions

1. Do not expose motor to humid, damp, or extreme temperature conditions.
2. Do not drill into motor.
3. Do not cut the antenna. Keep it clear from metal objects.
4. Do not allow children to play with this device.
5. If the power cable or connector is damaged, do not use.
6. Ensure the correct crown and drive adaptor are used.
7. Ensure the power cable and aerial is clear and protected from moving parts.
8. Gable routed through walls should be prope~y isolated.
9. Motor is to be mounted in horizontal position only.
10. Before installation, remove unnecessary cords and disable equipment not needed for powered operation.
11. Installation and programming should be performed by a qualified professional. Use or modification outside the scope of these instructions may void warranty.

| Do not dispose of In general waste.
Please recycle batteries and damaged electrical products appropriately,
---|---
| Please scan QR code to see more AMP product information
---|---

Charging Instructions

This motor connects with an external Li-ion battery pack with integrated charge management. Max power input for recharging: 5V 2A.
Before first use please charge motor for 6 hours using a 5V charger.
During operation, if the voltage is detected to be too low, the battery stops running and needs to be recharged.

Rechargeable Battery

Solid Red:
Charging in process

|

Solid Green:
Battery has finished
charging

---|---

P1 Button Instructions

① Test Motor (Wakes and Runs)

Happening as you press for 1 second

PressP1′ Less than 1 sec.

② Activate Pairing Mode

Happening as you press for 2 seconds

PressP1 Approx. 2 sec. Until Shade: Jog x1

③ Sleep Mode

Happening as you press for 6 seconds

PressP1  Approx. 6 sec.    Until Shade: Jog x2

④ Reverse Direction

Happening as you press for 10 seconds

PressP1 Approx. 1 O sec.  Until Shade: Jog x3

⑤ Reset To Factory Settings

Happening as you press for 14 seconds

PressP1 Approx.14sec.  Until Shade: Jog x4

Button Instructions

Essential Settings

The steps in factory mode must be completed to ensure proper operation.

Pair / Unpair Remote Control

a. Press “P1” button (about 2 sec) on the motor head until motor jog x1.

b. In the next 10 secs, press and hold “Stop” button on the remote control until motor jog x2.

Change Motor Direction (if necessary)

Press “Up” or “Down” button to check if the shade moves in the desired direction. If you need to reverse the direction, press and hold (about 2 sec) “Up” and “Down” buttons simultaneously until motor jog x1.

***** The operation is only valid when there are no limits. If the motor has already set the upper and lower limit, then you can only switch direction by pressing P1 button (See P1 button instructions).

Setting the Upper and Lower Limits

Set Upper Limit

a. Press “Up” button to raise the shade then press “Stop” button when it is in the desired upper limit.
b. Press and hold (about2sec) “Up” and “Stop” buttons simultaneously until motor jog x2.

Set Lower Limit

a. Press “Down” button to lower the shade, then press “Stop” button when it is in the desired lower limit.
b. Press and hold (about 2sec) “ Down” and “Stop” buttons simultaneously until motor jog x2.

***** If you exit the limit setting status before you finish the limit settings, the motor will take the previous existing limits.

Adjust Limits

Adjust the Upper Limit

a. Press and hold (about 5 sec) “Up” and “Stop” buttons simultaneously until motor jog x1.
b. Use “Up” button to raise the shade to the desired highest position, and use “Up” or “Down” button to do the final adjustment if necessary.

c. Press and hold (about 2sec) “Up” and “Stop” buttons simultaneously until motor jog x2.

Adjust the Lower Limit

a. Press and hold (about 5 sec) “Down” and “Stop” buttons simultaneously until motor jog x1.
b. Use “Down” button to lower the shade to the desired lowest position, and use “Up” or “Down” button to do the final adjustment if necessary.

c. Press and hold (about t 2sec) “Down ”and “Stop” buttons simultaneously until motor jog x2.

Favorite Position

Set Favorite Position

a. Use “Up” or “Down” button to move the shade to desired Favorite position.
b. Press one “P2” button on the back of remote control until motor jog x1.

c. Press and hold (about 2 sec) “Stop” button until motor jog x1.
d. Once more, press and hold (about 2sec) “Stop” button until motor jog x2.

Send Shade to Favorite Position

Press and hold (about 2 sec) “Stop” button, motor will move to Favorite position.

Delete Favorite Position

a. Press one “P2” button until motor jogx1.
b. Press and hold (about 2 sec) “Stop” button until motor jog x1.

c. Once more, press and hold (about 2sec) “Stop” button until motor jog x1.

Roller Mode and Sheer Mode

**Roller Shade Mode – continue movement after a short press – Default

Mode**

a. Press and hold (about 5 sec) “Up” and “Down” buttons simultaneously

until motor jog x1.

b. Press and hold (about 2 sec) “Stop” button until motor jog x2.

Sheer Shade Mode – jog movement after a short press (continue movement after a long press)

a. Press and hold (about 5 sec) “Up” and “Down” buttons simultaneously until motor jog x1.

b. Press and hold (about 2 sec) “Stop” button until motor jog x1.

Add or Remove Additional Remote

Using Current Remote Control

a. On the current remote control, press one “P2” button until motor jog x1.
b. Once more, on the current remote control, press one “P2” button until motor jog x1.

c . On the New remote control, press one “P2” button until motor jog x2.

***** Repeat the same procedure to remove additional remote control.

New Remote Control

Follow instructions under the section 1. Pair / Unpair Remote Control

Adjust Motor Speed

Acceleration Speed

a. Press one “P2” button until motor jog x1.
b. Press “Up” button until motor jog x1.

c. Once more, press “Up” button until motor jog x2.

Deceleration Speed

a. Press one “P2” button until motor jog x1.
b. Press “Down” button until motor jog x1.

c. Once more, press “Down” button until motor jog x2.

Declarations

U.S. Radio Frequency FCC Compliance

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

1. This device may not cause harmful interference, and
2. This device must accept any interference received, including interference that may cause undesired operation.

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/IV technician for help.

Any Changes or modifications not expressly approved by the party responsible for compliance could void the user~ authorly to operate the equipment.

JSEO RSS Warning:

This device complies with Innovation, Science and Economic Development Canada license -exempt ASS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device.

Quick Index

(hold down for 2s)
Lower Limit: Down (hold down for 2s) > Down + Stop (hold down for 2s)
4 Add / Remove Favorite Position| P2 > Stop > Stop
5 Roller Mode & Sheer Mode Switch| Up + Down (hold down for 5s) > Stop
6 Adjust Limits| Upper Limit: Up + Stop (hold down for 5s) > Up or Down > Up + Stop (hold down for 2s)
Lower Limit: Down + Stop (hold down for 5s) > Up or Down > Down + Stop (hold down for 2s)
7 Pair / Unpair Additional Emitter| P2 (existing) > P2 (existing) > P2 (new)
8 Speed Regulation| Acceleration: P2 > Up > Up
Deceleration: P2 > Down > Down

Troubleshooting

compatible AC adaptor and check connection and positioning of solar PV panel
Insufficient charging from Solar PV Panel| Check connection and orientation of solar PV panel
Remote control battery is discharged| Replace battery
Battery is inserted incorrectly into remote control| Check battery polarity
Radio interference/ shielding| Ensure remote control and antenna on the motor are positioned away from metal objects
Receiver is far away from Remote  Control| Move remote control to a closer position
Power failure| Check power supply to motor is connected and active
Incorrect wiring| Check that wiring is connected correctly (refer to motor installation instructions)
Cannot program a single motor (multiple motors respond)| Multiple motors are paired to the same channel.| Always reserve an individual channel for programming functions
SYSTEM BEST PRACTICE – Provide an extra 15 channel remote in your multi-motor projects that provides individual control for each motor for programming purposes
Place all other motors into sleep mode (ref to P1 button instructions)

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>