AMP Lighting APl-3033-B-BZ PetalPro Path and Area Light Instruction Manual
- June 3, 2024
- AMP Lighting
Table of Contents
AMP Lighting APl-3033-B-BZ PetalPro Path and Area Light
Important Safety Instructions: Read Before Installation
This luminaire is intended for installation in accordance with local codes and the National Electric Code (NEC). Failure to adhere to these codes and instructions may result in serious injury, property damage and void the war- ranty.
These instructions do not intend to cover all variations in installation, opera-tion maintenance or mounting situations.
- Make sure that the power is turned OFF before installing or servicing this fixture.
- Warning: this fixture is not intended to be installed within 10 feet [3 meters] of a pool, spa or fountain.
- This fixture is intended to be used only with a power supply (transform-er) rated maximum of 300 watts (25 AMPS) at 15 volts.
- Underground Low Energy Cable must not be buried over 6” (15.2 cm) in order to connect to the main low voltage cable.
- Wiring connections must be made with UL Listed wire connectors that are suitable for the application.
- Position the wire connector so that it is located within 6 inches (15.2 cm) from a building structure, a luminaire, or fitting.
Important Safety Instructions
INSTRUCTIONS PERTAINING TO A RISK OF FIRE, OR INJURY TO PERSONS
Lighted lamp is HOT
WARNING: To reduce the risk of FIRE OR INJURY TO PERSONS.
- Turn off/unplug and allow to cool before reducing lamp.
- Lamp gets HOT quickly!
- Do not touch the hot lens, guard or cowl.
- Keep lamp away from materials that may burn.
- Do not touch lamp at any time.
- Use a soft cloth.
- Oil from skin may damage lamp.
- Do not operate the fixture with a damaged or missing lens or shield.
Package Contents
- A. (1) Fixture Body
Product Dimensions
- A. (1) Mounting Accessory
- B. (1) GU4 or M11 LED Bulb
INSTALLATION & MAINTENANCE GUIDE
Remove Lens
Using a screwdriver, loosen screws on the lens and remove the lens from the
shade.
Install Bulb
Insert bulb with correct wattage and type marked on fixture label and push
into place.
CAUTION: Do not exceed maxi-mum wattage marked on fixture label.
Install Lens
Place the lens back onto the shade and secure with previously removed screws.
Tighten until snug with screwdriver.
Install Stake
Determine the desired location for mounting the luminaire. Hammer the stake
into the ground until flange of stake is flush to grade. To avoid damage to
the stake, place a board on top of the stake while hammer-ing.
Note: If the ground is hard and the stake is difficult to install, make a crosscut in the ground using a flat shovel.
Install Fixture Body to Stake
Pass supply wires through the center hole of the stake and thread the stem
onto the stake. Hand tighten until snug. Clear away area in ground and lay
supply wires into wireway slots.
Wire Connections
Strip two leads from fixture wires. Using two UL listed wire connectors (sold separately), connect leads from fixture wires to main supply cable leads.
Adjust Shade Direction
Loosen the knuckle to adjust the shade to your desired angle. Once your desired angle is achieved, hand tighten the lock screw to secure the shade direction.
Install/Replace Bulb
Please reverse Step 1 – Step 3 to expose the bulb and replace it with the
correct wattage and type marked on the fixture label.
IMPORTANT: The Bulb must be protected from moisture and dust at all
times. Always reinstall the lens when removed.
- customersupport@amplighting.com
- 813.978.3900
Specifications and product details subject to change without notice.© Copyright 2022, AMP® Lighting, Lutz FL USA 33549
- All rights reserved. customersupport@amplighting.com
- 813.978.3900
Help Hotline:
- 1-813-978-3900
- Mon-Fri 9am-6pm (EST)
- www.amplighting.com
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>