AMP Lighting AMPCEL Series Double Shaft Motor User Manual

: June 3, 2024
: AMP Lighting

AMP Lighting AMPCEL Series Double Shaft Motor User Manual

Fields of Appl1cat1on

Specif1cat1ons

Working temperature: -10° C – +50″ C
Input Voltage: USB 5V 1 A / USB 5V 2A
Radio Frequency: 433.92 MHz
Maximum Running Time: 6 minutes
The motor is suitable for motorization of cellular shades and cellular skylight

M d I Rated Torque Rated Speed Rated Power o e (N.m) (RPM) (W)
AMPCEL-0.8/40 0.8 40 14

Attention

Never drop, knock, drill or submerge the motor. Keep the power cable in the proper position as shown below.
Read all safety instructions before installation. Incorrect installation can lead to serious injury and will void manufacturer’s liability and warranty.

Safety Instructions

Do not expose motor to humid, damp, or extreme temperature conditions.
Do not drill into motor.
Do not cut the antenna. Keep it clear from metal objects.
Do not allow children to play with this device.
If the power cable or connector is damaged, do not use.
Ensure the correct crown and drive adaptor are used.
Ensure the power cable and aerial is clear and protected from moving parts.
Gable routed through walls should be properly isolated.
Motor is to be mounted in horizontal position only.
Before installation, remove unnecessary cords and disable equipment not needed for powered operation.
Installation and programming should be performed by a qualified professional. Use or modification outside the scope of these instructions may void warranty.

This motor connects with an external Li-ion battery pack with integrated charge management.
Max power input for recharging: 5V 2A.
Before first use please charge motor for 6 hours using a 5V charger.
During operation, if the voltage is detected to be too low, the battery stops running and needs to be recharged.

Rechargeable Battery

P1 Button Instructions

Test Motor (Wakes and Runs)
Happening as you press for 1 second
Activate Pairing Mode
Happening as you press for 2 seconds
Sleep Mode Happening as you press for 6 seconds
Reverse Direction
Happening as you press for 10 seconds
Reset To Factory Settings
Happening as you press for 14 seconds

Button Instructions

Essential Settings

The steps in factory mode must be completed to ensure proper operation.

1. Pair / Unpair Remote Control

2. Change Motor Direction (if necessary)

3. Setting the Upper and Lower Limits

4. Adjust Limits

5. Favorite Position

5.1 Set Favorite Position
a. Use “Up” or “Down” button to move the shade to desired Favorite position.
b. Press one “P2” button on the back of remote control until motor jog x1.
c. Press “Stop” button until motor jog x1.
d. Once more, press “Stop” button until motor jog x2.

5.2 Send Shade to Favorite Position
Press and hold (about 2 sec) “Stop” button, motor will move to Favorite position.
5.3 Delete Favorite Position
a. Press one “P2” button until motor jog x1.
b. Press “Stop” button until motor jog x1.
c. Once more, press “Stop” button until motor jog x1.

6. Roller Mode and Sheer Mode

6.1 Roller Shade Mode – continue movement after a short press – Default Mode
a. Press and hold (about 5 sec) “Up” and “Down” buttons simultaneously until motor jog x1.
b. Press and hold (about 2 sec) “Stop” button until motor jog x2.

6.2 Sheer Shade Mode – jog movement after a short press (continue movement after a long press)
a. Press and hold (about 5 sec) “Up” and
“Down” buttons simultaneously until motor jog x1.
b. Press and hold (about 2 sec) “Stop” button until motor jog x1.

7. Add or Remove Additional Remote

7.1 Using Current Remote Control
a. On the current remote control, press one “P2” button until motor jog x1.
b. Once more, on the current remote control, press one “P2” button until motor jog x1.
c. On the New remote control, press one “P2” button until motor jog x2.

*Repeat the same procedure to remove additional remote contro

7.2 Use Motor P1 Button a. Hold “P1” button on motor head until motor jog x1.
b. On New remote control, press and hold (about 2 sec) “Stop” button until motor jog x2.

8. Adjust Motor Speed

8.1 Acceleration Speed
a. Press one “P2” button until motor jog x1.
b. Press “Up” button until motor jog x1. c. Once more, press “Up” button until motor jog x2.

8.2 Deceleration Speed

a. Press one “P2” button until motor og x1.
b. Press “Down” button until motor jog x1.
c. Once more, press “Down” button until motor jog x2.

*If the motor has no response, it already has a Maximum or Minimum speed.

Declarations

U.S. Radio Frequency FCC Compliance
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interterence, and
(2) This device must accept any interterence received, including interterence that may cause undesired operation.
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part
15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interterence in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interterence to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
Any Changes or modifications not expressly approved by the party responsible for compliance could void the user~ authority to operate the equipment.

JSED RSS Warning:

This device complies with Innovation, Science and Economic Development Canada licence-exempt ASS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and
(2) this device must accept any interterence, including interterence that may cause undesired operation of the device. Le present appareil est conforme aux CNR d’ISED applicables aux appareils radio exempts de licence. ~exploitation est autorisee aux deux conditions suivantes: (1) l’appareil ne doit pas produire de brouillage, et (2)
l’utilisateur de l’appareil doit accepter tout brouillage radioelectrique subi, meme si le brouillage est susceptible d’en compromettre le fonctionnement.