AMP28B DC Tubular Motor with Built In Rechargeable Battery User Manual

AMP28B DC Tubular Motor with Built In Rechargeable Battery User Manual

Declarations

U.S. Radio Frequency FCC Compliance

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

1. This device may not cause harmful interference, and
2. This device must accept any interference received, including interference that may cause undesired operation.

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

Any Changes or modifications not express!), approved by the party responsible for compliance could void the user’s authority to operate the equipment.

ISED RSS Warning:
This device complies with Innovation, Science and Economic Development Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions:

1. this device may not cause interference, and
2. this device must accept any interference, including interference that may cause undesired operation

Quick Index Settings

Settings| Steps|
---|---|---
1| Pd| P1 (hold down for 2s) > Stop (hold down for 2s)
2| Switch Rotating Direction| Up + Down ChM down for 2s)
3| Setting Upper s Limiits| Upper Limit: Up (hold down for 2s) > Up + Slop Mold down for 2s) Lower Limit: Down (hold down for 2s)
4| Add / Remove Favorite Position| P2 > Slop > Slop
5| Roller Mode & Sheer Mode Switch| Up + Down (hoP down for 5s) > Stop
6| Adjust| Upper Limit: Up + Stop (hold down for 5s) > Up or Down > Up + Stop (hold dovm for 2s)
7| Pair / Unpair Additional Emitter| (existing) > P2 (existing) > P2 (new)
8| Speed Regulation| P2 > Up > Up 8 Deceleration: P2 > Down > Down

Troubleshooting

compatible AC adaptor and check connection and positioning of solar PV panel
Insufficient charging from Solar PV Panel| Check connection and orientation of solar PV panel
Remote control battery is discharged| Replace battery
Battery is inserted incorrectly into remote control| Check battery polarity
Radio interference / shielding| Ensure remote control and the antenna on the motor are positioned away from metal objects
Receiver is tar away from memote Control| Move remote control to a closer position
Power failure| Check power supply to motor is connected and active
Incorrect wiring| Check that wiring is connected correctly (refer to motor installation instructions)
Motor beeps 10 time when in use| Battery voltage is low / PV (solar panel issue)| Recharge with AC adapter or check connecbon and positioning of solar PV panel
Connot program a single motor (muitile motors respond| Multiple motors are paired to the same channel.| Ahvays reserve an individual channel for programming functions
SYSTEM BEST PRACTICE – Provide an extra 15 channel remote in your multi-motor projects that provides individual control for each motor for programming
Place all other motors into sleep mode get to P1 button Instructions)

Fields of Application

Roller

Sheer

Banded

Roman

Specifications

• Working temperature : -10° C — +50° C
• Input Voltage: USB 5V 1 A / USB 5V 2A : Maximum Running Time: 6 minutes

The motor is suitable for motorization of roller shades, sheer shades, roman shades, and revolve shades.

Attention

Never drop, knock, drill or submerge the motor. Keep the power cable in the proper position as shown below. Read all safety instructions before installation. Incorrect installation can lead to serious injury and will void manufacturer’s liability and warranty.

Safety Instructions

1. Do not expose motor to humid, damp, or extreme temperature conditions.
2. Do not drill into motor.
3. Do not cut the antenna. Keep it clear from metal objects.
4. Do not allow children to play with this device. 5. If the power cable or connector is damaged, do not use.
5. Ensure the correct crown and drive adaptor are used.
6. Ensure the power cable and aerial is clear and protected from moving parts.
7. Cable routed through walls should be properly isolated.
8. Motor is to be mounted in horizontal position only.
9. Before installation, remove unnecessary cords and disable equipment not needed for powered operation.
10. Installation and programming should be performed by a qualified professional. Use or modification outside the scope of these instructions may void warranty.

Do not dispose of in general waste. Please recycle batteries and damaged electrical products appropriately.

Please scan OR code to see more AMP'” product information

Charging Instructions

This motor has a built in Li-ion battery pack with integrated charge management. Max power input for recharging: 5V 2A.

Before first use please charge motor for 6 hours using a 5V charger.

During operation, when the motor starts, the buzzer will beep 10 times, indicating a low-voltage alarm and needs to be charged.

During operation, if the voltage is detected to be too low, the battery stops running and needs to be recharged.

Rechargeable Battery

Blinking red: Low battery alert

Blinking green: Charging in process

Solid green: Battery has finished charging

Button Instructions

Button Instructions

Essential Settings
The steps in factory mode must be completed to ensure proper operation.

Pair / Unpair Remote Control

a. Press “P1” button (about 2 sec) on the motor head until motor jog x1 and beep x1.
Action on Motor

b. In the next 10 secs, press and hold “Stop” button on the remote control until motor jog x2 and beep x3.
Motor Response Action on Remote Control

Repeat the same procedure to unpair remote control.
Motor Response

Change Motor Direction (if necessary)

Set Upper Limit

a. Press “Up” button to raise the shade, then press “Stop” button when it is in the desired upper limit.
Action on Remote Contro
b. Press and hold (about 2 sec) “Up” and “Stop” buttons simultaneously until motor jog x2 and beep x3.
Motor Response

Set Lower Limit

a. Press “Up” button to raise the shade, then press “Stop” button when it is in the desired upper limit.
Action on Remote Control

b. Press and hold (about 2 sec) “Up” and “Stop” buttons simultaneously until motor jog x2 and beep x3.
Motor Response

If you exit the limit setting status before you finish the limit settings, the motor will take the previous existing limits.

Factory Mode Complete User Mode Begins

Adjust Limits

Adjust the Upper Limit

A. Press and hol out 5 sec) “Up” and “Stop” buttons simultaneously until motor jog x1 and beep x1.
Action on Remote Control

b. Use “Up” button to raise the shade to the desired highest position, and use “Up” or “Down” button to do the final adjustment if necessary.
Motor Response

c. Press and hold (about 2 sec) “Up” and “Stop” buttons simultaneously until motor jog x2 and beep x3.
**Action on Remote Control Motor Response

Adjust the Lower Limit

a. Press and hold (about 5 sec) “Down” and “Stop” buttons simultaneously until motor jog x1 and beep x1
Action on Remote Control

b. Use “Down” button to lower the shade to the desired lowest position, and use “Up” or “Down” button to do the final adjustment if necessary.
Motor Response Action on Remote Control

c. Press and hold (about 2 sec) “Down” and “Stop” buttons simultaneously until motor jog x2 and beep x3.
Motor Response

Send Shade to Favorite Positio n

Press and hold (about 2 sec) “Stop” button, motor will move to Favorite position.
Action on Remote Contror Shade Response

Delete Favorite Position

a. Press one “P2” button until motor jog and beep x1.
Action on Remote Control

b. Press and hold (about 2 sec) “Stop” button until motor jog and beep x1.
Motor Response

c. Once more, press and hold (about 2 sec) “Stop” button until motor jog x1 and long beep x1.
Action on Remote Control Motor Response

Roller Mode and Sheer Mode

Roller Shade Mode – continue movement after a short press – Default Mode

a. Press and hold (about 5 sec) “Up” and “Down” buttons simultaneously until motor jog x1.
Action on Remote Control Motor Response

b. Press and hold (about 2 sec) “Stop” button until motor jog x2 and beep x3.
**Action on Remote Control Motor Response

Sheer Shade Mode – jog movement after a short press (continue movement after a long press)**

a. Press and hold (about 5 sec) “Up” and “Down” buttons simultaneously until motor jog x1.
Action on Remote Control  Motor Response

b. Pressand hold (about 2 sec) “Stop” button until motor jog x1 and beep x1.
Action on Remote Control Motor Response

Add or Remove Additional Remote

Using Current Remote Control

A. On the current remote control, press one “P2” button until motor jog x1 and beep x1.
Action on Current Motor Response
B. Once more, on the current remote control, press one “P2” button until motor jog x1 and beep x1.

C. On the New remote control, press one “P2” button until motor jog x2 and beep x3.
Action on Remote Control Motor Response

Repeat the same procedure to remove additional remote control.

New Remote Control

Follow instructions under the section 1.
Pair / Unpair Remote Contro

Adjust Motor Speed

Acceleration Speed

a. Press one “P2” button until motor jog x1 and beep x1.
Action on Remote Control Motor Response

b. Press “Up” button until motor jog x1 and beep x1.

c. Once more, press “Up” button until motor jog x2 and beep x1.
Action on Remote Control Motor Response

Deceleration Speed

a. Press one “P2” button until motor jog x1 and beep x1.
Action on Remote Control Motor Response

b. Press “Down” button until motor jog x1 and beep x1.

c. Once more, press “Down” button until motor jog x2 and beep x1.
Action on Remote ControlMotor Response

Documents / Resources

| AMP AMP28B DC Tubular Motor with Built In Rechargeable Battery [pdf] User Manual
AMP28BV2, 2AU29AMP28BV2, AMP28B, DC Tubular Motor with Built In Rechargeable Battery, AMP28B DC Tubular Motor with Built In Rechargeable Battery, AMP28B DC Tubular Motor, DC Tubular Motor, Tubular Motor
---|---

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>