AMP ASPL-3030-B-BZ Solarium Brass LED Flame Path Light Installation Guide

AMP ASPL-3030-B-BZ Solarium Brass LED Flame Path Light

INSTALLATION

Important Safety Instructions: Read Before Installation
This luminaire is intended for installation in accordance with local codes and the National Electric Code (NEC). Failure to adhere to these codes and in- structions may result in serious injury, property damage and void the warran- ty.
These instructions do not intend to cover all variations in installation, opera-tion maintenance or mounting situations.
Please note that these solar fixtures are equipped with built-in photocells, so they will not turn on until it is dark enough. These fixtures will also require plenty of sunlight to function properly. It’s best to have the fixture in an area where the sun will get to it at all times throughout the day and where no am-bient lighting will affect the photocell at night. If your fixture is not function-ing at night, be sure that the on/off button has been engaged. See step one for details.

Important Safety Instructions

INSTRUCTIONS PERTAINING TO A RISK OF FIRE, OR INJURY TO PERSONS Lighted lamp is HOT!
WARNING – To reduce the risk of FIRE OR INJURY TO PERSONS.

1. Turn off/unplug and allow to cool before replacing lamp.
2. Lamp gets HOT quickly!
3. Do not touch the hot lens, guard or enclosure.
4.  Keep lamp away from materials that may burn.
5. Do not touch lamp at any time. Use a soft cloth. Oil from skin may dam-age lamp.
6. Do not operate the luminaire fitting with a missing or damaged shield.
   SAVE THESE INSTRUCTIONS

Package Contents

• A. (1) Fixture Body
• B. (1) Flame LED Lamp
• C. (1) 12” Stem

Package Contents

• A. Mounting Accessory

Product Dimensions

Remove Solar Panel

Using a screwdriver, loosen the screws to carefully remove the solar panel from the fixture body to avoid disconnecting the wires.

Install Flame Lamp

Use flame lamp with correct wattage and type marked on fixture label.
Align the pins in the bottom of the flame lamp to holes on the socket and push the flame lamp into the socket properly.
CAUTION: Do not exceed maximum wattage marked on luminaire label.

Install Solar Panel

Align the switch to the slot on the solar panel and place the solar panel back onto the fix-ture body. Secure them togeth-er with previously removed screws. Hand tighten until snug with a screwdriver.

Test Solar Light

Place the solar panel of the fix-ture onto a flat opaque working surface. Push the switch on the flange “ON” to test the light source. The lights will turn on while the switch is on.
Now you can proceed to the next steps of installation knowing the fixture is in ON mode.

Install Stake

Determine the desired location for mounting the luminaire. Hammer the stake into the ground until flange of stake is flush to grade. To avoid damage to the stake, place a board on top of the stake while hammering.
NOTE: If the ground is hard and the stake is difficult to install, make a crosscut in the ground using a flat shovel.

Install Fixture Body

Thread the fixture body and the stem onto the stake and hand tighten until snug.

How to Replace Battery

Remove Solar Panel

Using a screwdriver, loosen the screws to carefully remove the solar panel from the fixture body to avoid disconnecting the wires.

Replace Battery

Remove the battery out of the battery compartment and replace it with a new one.

Install Solar Panel

Align the switch to the slot on the solar panel and place the solar panel back onto the fix-ture body. Secure them togeth-er with previously removed screws. Hand tighten until snug with a screwdriver.

Help Hotline:
1-813-978-3900 • Mon-Fri 9am-6pm (EST)
Specifications and product details subject to change without notice.
© Copyright 2022, AMP® Lighting, Lutz FL USA 33549 • All rights reserved. customersupport@amplighting.com • 813.978.3900
www.amplighting.com

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>