Indu-Sol PROmesh P8 Plus F Industrial Ethernet Switches User Guide

: June 3, 2024
: Indu-Sol

Table of Contents

Indu-Sol PROmesh P8 Plus F Industrial Ethernet Switches
Device Connections
Technical Data
General Information
Safety Instructions
Scope of Delivery
Mounting on the DIN Rail
Power Supply
Configuring a Network Connection
Accessing the Web User Interface
Interpreting LED Displays
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

Indu-Sol PROmesh P8 Plus F Industrial Ethernet Switches

All accompanying materials of the product can be found at:https://sdx .indu-sol.com/s/F9nmtrmtfbzy367

Device Connections

Indu-Sol-PROmesh-P8-Plus-F-Industrial-FIG-2

Technical Data

Voltage Supply	2x 24 VDC
Max. Current Consumption	0,8A
Max. Power Consumption	8W
Size (H x W x D)	130 x 150 x 60 mm
Weight	900 g
Mounting	35 mm DIN rail
Protection Class	IP20
Storage temperature	-40°C .. 75°C
Operating temperature	-40°C .. 75° C
Relative Humidity	5% .. 95%, RHD non-condensing
PROFINET Conformance	Class B
PROFINET standard	PROFINET 2.4
Port Mirroring	Rx, Tx+Rx
PROFINET Netload Class	Class III
Data Ports	8x 10/100/1000MBit/s RJ45
Switching Mode	Store & Forward
Diagnosis & Management	Online wire monitoring

Leakage current monitoring Network load monitoring Port-Mirroring

DCP, I&M

SNMPv1, v2c, v3 SD Card

General Information

The PROmesh P8+F is a full-managed Ethernet/PROFINET switch for industrial automation systems which can be easily and conveniently configured via a web UI. It enables uncomplicated installation of bus, star and ring structures with switching functionality.

Safety Instructions

Before putting the PROmesh P8+F into operation, check whether it is in perfect condi-tion externally. Always observe the technical specifications of the device to ensure safe and optimal use. The PROmesh P8+F is designed for IP20 protection environments. Take appropriate measures to ensure proper operation of the unit in a different environment.

WARNING
In case of suspected damage, please return the PROmesh P8+F immediately to your supplier and do not put it into operation. Do not open the housing under any circumstances. Unauthorized opening of the housing will void any warranty claims. The PROmesh P8+F is designed for use in PROFINET applications according to Confor-mance Class B. For complete support of the PROFINET standards, please also observe the selection, layout and wiring of the data ports according to these standards.

Scope of Delivery

PROmesh P8+F
5-pole 5 mm terminal block (power supply and alarm contact)
Quickstart User Guide (hardcopy)
SD Card, can be used for backup and updates

Mounting on the DIN Rail

Mount the PROmesh P8+F upright in the switch cabinet on a 35 mm DIN rail (DIN EN 60715).

NOTE
The following distances to other modules must be observed:

right / left : 50 mm
top / bottom: 50 mm

WARNING
Do not mount the PROmesh P8+F directly next to devices that generate strong electro-magnetic interference fields or constantly emit heat to their surroundings. Also protect the PROmesh P8+F from intense sunlight.

Power Supply

The PROmesh P8+F is operated with a DC voltage of 24 VDC, Connect a suitable power source to the labeled terminals of the 5-pin 2,5 mm2 terminal block. Connect the po-sitive lead to one of the VDC contacts and the ammunition lead to the corresponding GND contact. If the external power supply is correctly connected and activated, all status LEDs of the PROmesh P8+F will light up briefly. After a short initialization phase the LEDs go out and the device is ready for operation and can now be configured in the network.

Configuring a Network Connection

download the Service Tool to your client PC (Windows). You can find the software at the following link: www.indu-sol.com/en/servicetool

NOTE
Our software is updated regularly. Please, make sure you are using the latest version. Connect the PC to a suitable data line on one of the data ports (P1 â€“ 8). The PROmesh P8+F and the client PC must be located in the same IP address range and IP subnet. For this you have to assign a corresponding IP address to your PROmesh P8+F for the first time. Use the already installed ServiceTool. After assigning a suitable IP address and subnet mask, the Web UI of the PROmesh P8+F can be reached. The PROmesh P8+F is delivered with the following factory settings:

IP Adress	0.0.0.0
Subnet mask	0.0.0.0
Gateway	0.0.0.0
Username	admin
Password	admin

After successful installation and start of the software, you can scan the system with the search setting PROFINET-Gerät. The PROmesh P8+F is displayed in the search result. You can then make and save individual entries in the input mask.

NOTE
Make sure that the IP address you selected has not yet been assigned. If required, you can display IP addresses that have already been assigned using the PROscan® Active V2 license software from Indu-Sol.

WARNING
When logging in for the first time, you must change the factory-set password. It is your responsibility to document this password and protect it against unauthorized access

Accessing the Web User Interface

The device-specific functions of the PROmesh P8+F can be configured via an integrated Web-UI. Open your browser, enter the IP address of the PROmesh P8+F configured in the ServiceTool in your browser bar or use the above configuration data. Alternatively, you can right-click on the corresponding list entry in the context menu of the ServiceTool to select „to website“. The Web UI now opens in your standard browser.

NOTE
Further information on the configuration options and troubleshooting can be found at the following link: www.indu-sol.com/en/manual-promesh

Interpreting LED Displays

LED label	Mode	Meaning
VDC	Green	Voltage at terminal sufficient
Off	Voltage at terminal insufficient
Status	Green	Active connection to the PROFINET controller
Yellow	No active connection to the PROFINET controller
Error	Red	Power failure, port error or configured alarm active
Off	No power failure, no port error and no confi- gured alarm active