Indu-Sol PROmesh P20 Full-Managed Ethernet or PROFINET Switch for Industrial Automation Systems User Guide
- October 30, 2023
- Indu-Sol
Table of Contents
PROmesh P20 Full-Managed Ethernet or PROFINET
Switch for Industrial Automation Systems
User Guide
PROmesh P20 Full-Managed Ethernet or PROFINET Switch for Industrial
Automation Systems
WARNING
Commissioning and operation of this device may be carried out by qualified
personnel only. Qualified personnel are persons who are authorized to
commission, ground and label devices, systems and circuits in accordance with
the standards of safety engineering.
Something‘s wrong with your product?
You can reach our technical support team on weekdays between 07:30 am – 04:30
pm (CET) by telephone: +49(0)34491 / 580-321 or send us an e-mail: support
@indu-sol.com. We will get in touch with you
promptly.
Your system is at a standstill?
Reach out to our emergency service even outside our regular opening hours:
+49(0)34491 / 580-0.
How will I be informed about software updates?
New firmware versions or further documentation are updated for the PROmesh P20
at regular intervals. You can be informed about this automatically. To do
this, you must register for the update service under the link:
https://www.indusol.com/support/downloads/update-service/ to register for
the update service. We recommend that you always use the latest software
version and the latest documentation for the product.
Device Connections
Technical Data
| Voltage Supply | 2x 12 – 48VDC |
|---|---|
| Max. Current Consumption | 0,92A |
| Max. Power Consumption | 22W |
| Size (H x W x D) | 138 x 68 x 130 mm |
| Weight | 0,96 kg |
| Mounting | 35 mm DIN rail |
| Protection Class | IP30 |
| Storage temperature | -40°C .. 85°C |
| Operating temperature | 0°C .. 75° C |
| Relative Humidity | 5% .. 95%, RHD non-condensing |
| PROFINET Conformance | Class B |
| Routing | NAT Routing |
| Port Mirroring | Tx, Rx, Tx+Rx, Port selectable |
| PROFINET Netload Class | Class III |
| Data Ports | 16x Base-T, 1000Base-TX RJ-45 4x 1000Base-X SFP |
| Switching Mode | Store & Forward |
| Diagnosis & Management | Leakage current monitoring |
Network load monitoring
Port-Mirroring
PN-RTA
DCP, I&M
SNMPv1, v2c, v3
SD Card
The PROmesh P20 is a full-managed Ethernet/PROFINET switch for industrial
automation systems which can be easily and conveniently configured via a we
interface. It enables the configuration of bus, star and ring structures.
Before putting the PROmesh P20 into operation, check whether it is in perfect
condition externally. Always observe the technical specifications of the
device to ensure safe and optimal use. The PROmesh P20 is designed for IP30
protection environments. Take appropriate measures to ensure proper operation
of the unit in a different environment.
In case of suspected damage, please return the PROmesh P20 immediately to your
supplier and do not put it into operation.
Do not open the housing under any circumstances. Unauthorized opening of the
housing will void any warranty claims.
- PROmesh P20
- 7-pole pluggable 5 mm terminal block (power supply and alarm contact)
- Quackster User Guide (hardcopy)
- SD Card, can be used for backup and updates
Insert the SD card into the slot provided on the back of the PROmesh P20
before the first start-up.
Mount the PROmesh P20 upright in the switch cabinet on a on a 35 mm DIN rail
(DIN EN 60715).
The following distances to other modules must be observed:
- right / left: 20 mm
- top / bottom: 50 mm
! WARNING
Do not mount the PROmesh P20 directly next to devices that generate strong
electromagnetic interference fields or constantly emit heat to their
surroundings. Also protect the PROmesh P20 from intense sunlight.
Power Supply
The PROmesh P20 is operated with a redundant DC voltage of 12 – 48VDC, Connect
a suitable power source to the labeled terminals of the 7-pin 5,0 mm terminal
block.
Connect the positive lead to one of the VDC contacts and the ammunition lead
to the corresponding GND contact.
If the external power supply is correctly connected and activated, all status
LEDs of the PROmesh P20 will light up briefly. After a short initialization
phase the LEDs go out and the device is ready for operation and can now be
configured in the network.
! WARNING
Do not mount the PROmesh P20 directly next to devices that generate strong
electromagnetic interference fields or constantly emit heat to their
surroundings. Also protect the PROmesh P20 from intense sunlight.
Configuring a Network Connection
Download the Service Tool to your client PC (Windows). You can find the
software on our website: https://sdx.indu-sol.com/s/fZDLQTyzLPg9RPR
NOTE
Our software is updated regularly. Please, make sure you are using the latest
version.
Connect the PC to a suitable data line on one of the data ports (P1 – 16, G1 –
G4).
The PROmesh P20 is delivered with the following factory settings:
| IP Address | 0.0.0.0 |
|---|---|
| Subnet mask | 0.0.0.0 |
| Gateway | 0.0.0.0 |
| Username | admin |
| Password | admin |
You can customize them with the Service Tool already installed. Connect your
PC to one of the 20 available ports of the switch. Then perform a device scan
with the Service Tool. Make sure that the field „PROFINET device“ is selected
under the scan settings.
After you have performed the scan, you can adjust the IP address, the subnet
mask, the default gateway and the PROFINET name of the PROmesh P20 according
to your needs.
! NOTE
Make sure that the IP address you selected has not yet been assigned. If
required, you can display IP addresses that have already been assigned using
the Pros can® Active V2 license software from Indu-Sol.
! WARNING
We recommend to change the factory-set password at the 1st login. It is
your responsibility to document this password and protect it against
unauthorized access
Accessing the Web User Interface
The device-specific functions of the PROmesh P20 can be configured via an
integrated we interface. Open your browser, enter the IP address of the
PROmesh P20 configured in the Service Tool in your browser bar. Alternatively,
you can right-click on the corresponding list entry in the context menu of
the Service Tool to select „to website“.
The Web UI now opens in your standard browser.
! NOTE
Further information on the configuration options and troubleshooting can be
found in the supplied manual on our website: https://sdx.indu-
sol.com/s/fZDLQTyzLPg9RPR
Interpreting LED Displays
| LED label | Mode | Meaning |
|---|---|---|
| VDC1 | Green | Voltage at terminal sufficient |
| Off | Voltage at terminal insufficient | |
| VDC2 | Green | Voltage at terminal sufficient |
| Off | Voltage at terminal insufficient | |
| Status | Green | PROFINET connection to the controller active |
| Yellow | PROFINET connection to the controller inactive | |
| Error | Red | Power failure, port error or configured alarm active |
| Off | No malfunction at the port | |
| Data | Green | Connection established |
| Blinking | Sending / receiving data | |
| Off | No connection established |
Indu-Sol GmbH Ulmenstraße 3
04626 Schmillen
Telephone: +49 (0) 34491 580-0
Telefax: +49 (0) 34491 580-499
info@indu-sol.com
www.indu-sol.com
Certified according to DIN EN ISO 9001:2015
https://sdx.indu-sol.com/s/fZDLQTyzLPg9RPR
All accompanying materials of the product can be found at: https://sdx.indu-
sol.com/s/fZDLQTyzLPg9RPR
References
- Sol.com | Welcome
- Indu-Sol | Feldbusse & industrielle Netzwerke optimieren
- SDX
- Indu-Sol | Feldbusse & industrielle Netzwerke optimieren
- Support – Wir sind für Sie da | Indu-Sol
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>