Indu-Sol PROmesh B8 8-Port Industrial Managed Switch User Guide
- June 12, 2024
- Indu-Sol
Table of Contents
Indu-Sol PROmesh B8 8-Port Industrial Managed Switch
Product Information
The PROmesh B8 is a full-managed Ethernet/PROFINET switch for industrial automation systems. It allows for easy configuration through a web UI and supports the installation of bus, star, and ring structures with switching functionality. The switch has 8 data ports with RJ45 connectors and supports a voltage supply of 2x 24 VDC. It has a maximum current consumption of 0.8 A and a maximum power consumption of 8W. The switch is designed for mounting on a 35 mm-Hutschiene (DIN EN 60715) in a vertical position inside a control cabinet. It is protected against dust and water ingress with a protection class rating. The switch operates within a storage temperature range and an operating temperature range, and supports various protocols and management features such as PROFINET Conformance, Port Mirroring, and Network load monitoring.
Product Usage Instructions
-
Mounting:
- Mount the PROmesh B8 in an upright position on a horizontal 35 mm-Hutschiene (DIN EN 60715) inside the control cabinet.
-
Power Supply:
- Connect the power supply to the VDC1 and VDC2 terminals using DC 24V. Connect the GND terminals to 0V Mass.
-
Network Configuration:
-
Download the ServiceTool software from the following link:
https://sdx.indu-sol.com/s/WnL7ddafkq77cqZ -
Assign an appropriate IP address and subnet mask to the PROmesh B8. The default factory settings are:
-
IP Address: 0.0.0.0
-
Subnet Mask: 0.0.0.0
-
Gateway: 0.0.0.0
-
Username: admin
-
Password: admin
-
-
LED Indicators:
- Refer to the following link for interpreting the LED indicators: https://sdx.indu-sol.com/s/WnL7ddafkq77cqZ
Indu-Sol GmbH – Specialist in Industrial Networks
Device Connections
Technical Data
General Information
The PROmesh B8 is a full-managed Ethernet/PROFINET switch for industrial automation systems which can be easily and conveniently configured via a web UI. It enables uncomplicated installation of bus, star and ring structures with switching functionality.
Safety Instructions
Before putting the PROmesh B8 into operation, check whether it is in perfect condition externally. Always observe the technical specifications of the device to ensure safe and optimal use. The PROmesh B8 is designed for IP30 protection environments. Take appropriate measures to ensure proper operation of the unit in a different environment.
WARNING : In case of suspected damage, please return the PROmesh B8 immediately to your sup-plier and do not put it into operation. Do not open the housing under any circumstances. Unauthorized opening of the housing will void any warranty claims. The PROmesh B8 is designed for use in PROFINET applications according to Conformance Class B. For complete support of the PROFINET standards, please also observe the selection, layout and wiring of the data ports according to these standards.
Scope of Delivery
- PROmesh B8
- 7-pole 5 mm terminal block (power supply and alarm contact)
- Quickstart User Guide (hardcopy)
Mounting on the DIN Rail
Mount the PROmesh B8 upright in the switch cabinet on a 35 mm DIN rail (DIN EN 60715).
NOTE
The following distances to other modules must be observed:
- Right / left: 50 mm
- Top / bottom: 50 mm
WARNING
Do not mount the PROmesh B8 directly next to devices that generate strong electro-magnetic interference fields or constantly emit heat to their surroundings. Also protect the PROmesh B8 from intense sunlight.
Power Supply
The PROmesh B8 is operated with a redundant DC voltage of 24 VDC, Connect a
suitable power source to the labeled terminals of the 7-pin 2,5 mm2 terminal
block. Connect the positive lead to one of the VDC contacts and the ammunition
lead to the corresponding GND contact. If the external power supply is
correctly connected and activated, all status LEDs of the PROmesh B8 will
light up briefly. After a short initialization phase the LEDs go out and the
device is ready for operation and can now be configured in the network.
Configuring a Network Connection
Download the Service Tool to your client PC (Windows). You can find the
software at the following link:
https://sdx.indu-sol.com/s/WnL7ddafkq77cqZ
NOTE
Our software is updated regularly. Please, make sure you are using the
latest version. Connect the PC to a suitable data line on one of the data
ports. The PROmesh B8 and the client PC must be located in the same IP address
range and IP subnet. For this you have to assign a corresponding IP address to
your PROmesh B8 for the first time. Use the already installed Service Tool.
After assigning a suitable IP address and subnet mask, the Web UI of the
PROmesh B8 can be reached. The PROmesh B8 is delivered with the following
factory settings:
| IP Adress | 0.0.0.0 |
|---|---|
| Subnet mask | 0.0.0.0 |
| Gateway | 0.0.0.0 |
| Username | admin |
| Password | admin |
After successful installation and start of the software, you can scan the system with the search setting PROFINET-Gerät. The PROmesh B8 is displayed in the search result. You can then make and save individual entries in the input mask.
NOTE
Make sure that the IP address you selected has not yet been assigned. If
required, you can display IP addresses that have already been assigned using
the PROscan® Active V2 license software from Indu-Sol.
WARNING
When logging in for the first time, you must change the factory-set password.
It is your responsibility to document this password and protect it against
unauthorized access
Accessing the Web User Interface
The device-specific functions of the PROmesh B8 can be configured via an
integrated Web-UI. Open your browser, enter the IP address of the PROmesh B8
configured in the Service Tool in your browser bar or use the above
configuration data. Alternatively, you can right-click on the corresponding
list entry in the context menu of the Service Tool to select „to website“. The
Web UI now opens in your standard browser.
NOTE
Further information on the configuration options and troubleshooting can be
found at the following link:
https://sdx.indu-sol.com/s/WnL7ddafkq77cqZ
Interpreting LED Displays
| LED label | Mode | Meaning |
|---|---|---|
| VDC1 | Green | Voltage at terminal sufficient |
| Off | Voltage at terminal insufficient | |
| VDC2 | Green | Voltage at terminal sufficient |
| Off | Voltage at terminal insufficient | |
| Status | Green | Active connection to the PROFINET controller |
| Yellow | No active connection to the PROFINET controller | |
| Error | Red | Power failure, port error or configured alarm active |
| Off | No power failure, no port error and no configured alarm active | |
| Port Status | On | The port has established a valid network connection |
| Flashing | The port is in network communication exchange | |
| Off | The port has not established a valid network connection |
Indu-Sol GmbH
Blumenstraße 3
04626 Schmoelln
Germany
Telephone: +49 (0) 34491 580-0
Telefax: +49 (0) 34491 580-499
info@indu-sol.com
www.indu-sol.com
Certified according to DIN EN ISO 9001:2015
Alle Begleitmaterialien des Produkts finden Sie unter /All accompanying
materials of the product can be found at:
https://sdx.indu-sol.com/s/WnL7ddafkq77cqZ
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>