PELONIS PFS40A4BBB Remote Control Oscillating Stand Up Fan Owner’s Manual
- June 15, 2024
- Pelonis
Table of Contents
OWNER’S MANUAL
Stand Fan
Model: PFS40A4BBB
PFS40A4BWW
PFS40A4BBB Remote Control Oscillating Stand Up Fan
READ AND SAVE THESE INSTRUCTIONS
CAUTION
Read Rules for Safe Operation and Instructions Carefully.
WARNING
This appliance has a polarized plug (one blade is wider than the other). To
reduce the risk of electric shock, this plug is intended to fit in a polarized
outlet only one way. If plug does not fit fully in the outlet, reverse the
plug. If it still does not fit, contact a qualified electrician. Do not
attempt to defeat this safely feature.
WARNING: To Reduce The Risk Of Fire Or Electric Shock, Do Not Use This
Fan With Any Solid-State Speed Control Device.
RULES FOR SAFE OPERATION
- Never insert fingers, pencils, or any other object through the grille when fan is running.
- Disconnect fan when moving from one location to another.
- Disconnect fan when removing grilles for cleaning.
- Be sure fan is on a stable surface when operating to avoid overturning.
- Do not use fan in window. Rain may create electrical hazard.
- Ensure that the fan is switched off from the supply mains before removing the grille.
The rules about cord and plug as below:
- This product employs overload protection (fuse). A blown fuse indicates an overload or short-circuit situation. If the fuse blows, unplug the product from the outlet. Replace the fuse as per the user servicing instructions (follow product marking for proper fuse rating) and check the products. If the replacement fuse blows, a short-circuit may be present and the product should be discarded or returned to an authorized service facility for examination and/or repair.
- Do not operate any fan with a damaged cord or plug. Discard fan or return to an authorized service facility for examination and/or repair.
- Do not run cord under carpeting. Do not cover cord with throw rugs, runners, or similar coverings. Do not route cord under furniture or appliances. Arrange cord away from traffic area and where it will be tripped over.
INSTALLATION INSTRUCTIONS
Name of components
Base Installation
Align the column with the groove on the base and fix them together using a
right-angle bolt.
Considerate Hint: Remove ①②parts from the component before performing
installation.
Front and Rear Guard Installation
- Align Screw Holes on the outer ring of both the Front and Rear Guards, with the Positioning Clip aligned as illustrated.
- Press down all the Buckles to fasten the Front Guard with the Rear Guard. At the Screw Holes, tighten the separated screw and nut.
INSTRUCTIONS FOR USE
Instructions for key of remote controller
Considerate Hint:
Effective Range of Remote Control: within 5 m distance and 30-degree
deflection in front of Product.
Instructions for display of body
Instructions for operation of body
USER SERVICING INSTRUCTIONS
a) Grasp plug and remove from the receptacle or other outlet device. Do not
unplug by pulling on cord.
b) Open fuse cover. Slide open fuse access cover on top of attachment plug
towards blades.
c) Remove fuse carefully. Insert the tip of your tool into fuse slot (close
with the terminal), then prize the fuse gradually and slowly, but not
overexert. If you feel tight, you can try it at several times and prize the
fuse little by little. When one side of the fuse has been prized, then you can
get the fuse out entirely.
d) Risk of fire. Replace fuse only with 2.5 Amp, 125 Volt fuse.
e) Close fuse cover. Slide closed the fuse access cover on top of attachment
plug.
f) Risk of fire. Do not replace attachment plug. Contains a safety device
(fuse) that should not be removed. Discard product if the attachment plug is
damaged.
Notice:
- When you replace the fuse, please don’t operate suddenly or overexert, or else the product will be damage or cause accident.
- When you feel it hard to be operated, please make sure you have got the right way.
CLEANING
-
Be sure to unplug from the electrical supply source before cleaning.
-
Plastic parts should be cleaned with mild soap and a damp cloth or sponge.
Thoroughly to remove soap film with clean water. -
Be sure not to make water or other liquid enter inside of motor.
SERVICE & SUPPORT
In the event of a warranty claim or if service is required for this heater,
please contact us at the following:
Tel: 1-866-646-4332
Email us at:
customersupport@pelonis.com
For questions or comments, please write to:
Midea America Corporation
5 Sylvan Way, Parisippany, NJ 07054
For your records, staple your sales receipt to this manual and record the
following:
DATE OF PURCHASE: __
PLACE OF PURCHASE: _____
(STAPLE SALES RECEIPT HERE)
NOTE: PROOF OF PURCHASE IS REQUIRED FOR ALL WARRANTY CLAIMS
Printed in China
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>