SOUNDMAX SM-CCR3057F USB or MicroSD Media Player Instruction Manual
- June 3, 2024
- SOUNDMAX
Table of Contents
SM-CCR3057F
USB/microSD media player
Instruction manual
SM-CCR3057F USB or MicroSD Media Player
Dear customer!
Thank you for purchasing our product. For safety, it is strongly recommended
to read this manual carefully before connecting, operating and/or adjusting
the product and keep the manual for reference in the future. This device is
intended for installation in a vehicle with on board voltage 12 V. Designed to
receive radio FM This device is intended for installation in a vehicle with
onboard voltage 12 V. Designed to receive radio FM and playing MP3 from media
USB and microSD (TF). and playing MP3 from media USB and microSD (TF).
Important safeguards
- Read carefully through this manual to familiarize yourself with this high-quality sound system.
- The beginning of operation is the moment of the unit installation. Before use the device in winter it is recommended to heat up the passenger compartment during 20 seconds or to the operation temperature.
- Use the unit with the temperature that goes beyond the operation temperature greatly decreases the operation resource of the screen and other components of device and can result an outage.
- Disconnect the vehicle’s negative battery terminal while mounting and connecting the unit.
- When replacing the fuse, be sure to use one with an identical amperage rating. Using a fuse with a higher amperage rating may cause serious damage to the unit.
- Make sure that pins or other foreign objects do not get inside the unit; they may cause malfunctions, or create safety hazards such as electrical shock.
- Do not use the unit in places where it can be exposed to water, moisture and dust.
- Do not open covers and do not repair yourself. Consult the dealer or an experienced technician for help.
- Make sure you disconnect the power supply and aerial if you will not be using the system for a long period or during a thunderstorm.
- Make sure you disconnect the power supply if the system appears to be working incorrectly, is making an unusual sound, has a strange smell, has smoke emitting from it or liquids have got inside it. Have a qualified technician check the system.
- The unit is designed for negative terminal of the battery, which is connected to the vehicle metal. Please confirm it before installation.
- Do not allow the speaker wires to be shorted together when the unit is switched on. Otherwise it may overload or burn out the power amplifier.
Accessories
1. Receiver | 1 pc |
---|
2. Mounting parts:
Release key| 2 pcs
Mounting collar| 1 pc
3. Instruction manual| 1 pc
Installation/Connection
General notes
- Choose the mounting location where the unit will not interfere with the normal driving function of the driver.
- Before finally installing the unit, connect the wiring and make sure that the unit works properly.
- Consult with your nearest dealer if installation requires the drilling of holes or other modifications of the vehicle.
- Install the unit where it does not get in the driver’s way and cannot injure the passenger if there is a sudden stop, like an emergency stop.
- Avoid installing the unit where it would be subject to high temperature, such as from direct sunlight, or from hot air, from the heater, or where it would be subject to dust, dirt or excessive vibration.
- Install the sleeve into the dashboard; ensure it is installed with the correct side and there are no obstacles (wires, dashboard elements, etc) for the unit installation.
- After installing the sleeve into the dashboard, bend tabs fitting to the size of the dashboard to fix the sleeve in place.
- Make the necessary wire connections. Ensure the connections are correct.
- Install the unit into the sleeve until the side locks are fixed .
1. Dash board
2. Sleeve tab to bend
Dismantling the unit
- Make sure the ignition is turned off, then disconnect the cable from the , for this you need to break the plastic plugs. vehicle battery’s negative (-) terminal.
- Remove the metal strap attached the back of the unit (if attached).
- Insert both of the supplied keys into the slots at the middle left and right sides of the unit, then pull the unit out of the dashboard, for this you need to break the plastic plugs.
Connection diagram
A1-RR+ | A3-FR+ | A5-FL+ | A7-RL+ |
---|---|---|---|
A2-RR- | A4-FR- | A6-FL- | A8-RL- |
B4-B+ | B5-ANT | B7-ACC | B8-GND |
Notes:
- In spite of having any kinds of speaker system, must use 4 ohms impedance of speaker to reduce the distortion during high volume level.
- It is prohibited making the conductors of auto antenna and ground touch with each other.
- The negative electrode of the speaker mustn’t be grounded, or else it may burn the player!
- The negative electrode of the speaker mustn’t be grounded, or else it may burn the player!
Attention, connection ISO need be carefully matched with description on RL, connection any wrong cables (WHITE-BLACK/ GREEN-BLACK/ PURPLE-BLACK/ GRAY- BLACK) with Black cable (Ground) can be reason of defect of built-in amplifier.
Control elements
Front panel
Power/Mute/Pause
- Power/Mute/Pause
- MOD/CLK button
- VOLUME knob/SE L button
- button
- LCD
- IR reciever
- USB port
- AUX input
- Micro SD (TF) card slot
- Reset button (hole)
- button
- BND/AMS button
General operations
Turning the unit on/off
Press the button to turn the unit on. Press the button again to turn the unit
off.
In the radio state, short press this key into the mute state.
In the USB/SD/TF state, short press this key into the pause state.
Reset the unit
When first using the device or after replacing the car battery, you must reset
the unit. Press the RESET button (hole) with a pointed object (such as a
ballpoint pen) to set the unit to its initial state. When some errors occur,
you can also press the RESET button to return to factory settings, but note
that it will erase clock setting and some memorized functions.
Mode selection
Press the MOD/CLK button repeatedly to select between Radio, AUX, USB and SD
modes. Operation modeare indicated on the display. USB and SD mode is not
available unless a memory card or a USB device is connected.
Volume control
Adjust the volume by rotating the VOLUME knob.
In player state, press and this key to enter BAL/EQ/INT/RPT/RDM function, and
use volume knob to select respective function.
Clock
Press and hold the MOD/CLK to show the time for 5 seconds. When the time is
shown, press and hold the button until the clock starts to blink, then rotate
the volume knob to set the current hour. Then press the button again to adjust
minutes (the minutes on display will blink), rotate the volume knob to set the
current minutes. Press the button again to confirm the clock setting.
Audio parameter setting
In player/radio mode, short press the volume knob to enter ST/MONO and
dH/LOC/CH/STEP (i.e. Radio stereo/Mono channel, Short/long-range receiver,
Manual search and Frequency step) function, and turn VOL knob to select the
relevant function.
In player state, press this key to enter BAL and EQ function, and use the
volume knob to select respective function.
In player state, press and hold this key to select files, press and hold it
again to select and play next folder, and so on.
AUX input
AUX-in jack is intended for connecting an external audio equipment to amplify
the sound. If connection is made correctly, the audio signal from the external
source will be transmitted through the acoustics of the head unit. This
enables to adjust the volume and quality of the sounding. For example, you can
connect an MP3 player to listen to tracks using the car acoustic system.
Radio operations
Band select
In Radio mode press the BND/AMS button to select a radio band: FMl => FM2 =>
FM3.
Manual/automatic tuning
-
In radio mode, short press VOL knob three times into “CH” mode and turn the VOL knob into the “STEP” mode, short press or to select radio stations. Once the operation stops for more than 5 s, the system will be return to “CH” mode.
-
In “STEP” mode, after manually selecting the right radio station, long press or button to store it. Display will blink three times to confirm this storage and the previous station will be replaced.
-
Press and hold or button, the unit will start the automatic search of a next or previous station with a strong signal in this band.
Storing and recalling stations -
Press and hold the BND/ AMS button for several seconds to automatically find and store 6 strongest stations in the current band. Each band can have 6 stations, for a total of 18 stations.
-
Press shortly or button. The radio will select the previous or next stored station.
USB/TF operations
TF card slot
Carefully insert the TF card into the card slot on the front panel. Unit
starts playback automatically. To disconnect the memory card, press it until a
click, and then carefully pull it out from the slot.
USB port
Carefully connect a USB driver to the USB jack on the front panel. Unit starts
playback automatically.
USB/SD notes
USB format supports 2.0. Capacity: up to 32 GB. MicroSD/TF cards capacity: up
to 32 GB. Supported file systems are FAT/FAT32.
Note: Because of the great variety of products with SD-card slots and
their sometimes quite manufacturer specific functions the producer can
neither guarantee that all devices will be recognized nor that all operating
options that are possible in theory will actually work. Before disconnecting a
storage, switch the unit to another mode.
Next/Previous track
Press or buttons to choose next or previous track. Press and hold this button
to choose forward playback or backward playback; release the button to return
to normal playback.
Troubleshooting guide
Below is a table describing simple measures that can help you eliminate most problems likely to emerge when this unit is in use. If below measures do not help, turn to a service center or to the nearest dealer.
Symptom | Cause | Solution |
---|---|---|
No power | Wiring is connected incorrectly. | Make correct wiring connection. |
The car ignition is not on. | If the power supply is properly connected to the |
car accessory, switch the ignition on.
The fuse is blown.| Replace the fuse.
No sound| Volume is in minimum.| Adjust volume to the desired level.
Wiring is not properly connected.| Check wiring connection.
The radio does not work| The antenna cable is not connected.| Insert the
antenna cable properly.
The radio station automatic tuning does not work| The signals are too weak.|
Select stations manually.
Cleaning the unit body
Wipe with a soft cloth. If the cabinet is very dampen (not dropping wet) the
cloth with a weak solution of soapy water, and then wipe clean.
Specification
General
Maximum power output| 4 x 40 W
Required speaker impedance| 4 Ohm
Fuse| 5 A
Unit dimensions| 178 x 50 x 38 mm
Net weight| 0.36 kg
Working temperature range| from -20 degree to +60 degree
FM stereo radio
Frequency range| 87.5 – 108.0 MHz
Frequency step| 0,1 MHz
Preset stations| 18
Stereo separation| >25 dB
Player
Supported storages| USB/microSD/TF
Support formats| Playback MP3 files from USB/TF (microSD) carriers
Line out| Stereo RCA output (2 V)
Line-in (AUX)| Mini Jack 3.5mm
Power supply
Supply voltage| DC 12V
Specifications are subject to change without notice. Dimensions are approximate.
Documents / Resources
|
SOUNDMAX SM-CCR3057F USB or MicroSD Media
Player
[pdf] Instruction Manual
SM-CCR3057F, USB or MicroSD Media Player, SM-CCR3057F USB or MicroSD Media
Player, MicroSD Media Player, Media Player
---|---
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>