dji INSPIRE 1 AIR MAVIC MINI Drone User Guide
- June 9, 2024
- DJi
Table of Contents
INSPIRE 1 AIR MAVIC MINI Drone
User Guide
INSPIRE 1
Quick Start Guide
V2.2
INSPIRE 1 AIR MAVIC MINI Drone
INSPIRE 1
The Inspire™ 1 is a professional aerial filmmaking and photography platform
that is ready to fly right out of the box. Featuring an onboard camera
equipped with a 20mm lens and 3-axis stabilized gimbal, it shoots sharp 12mp
stills and stable video at up to 4K. Its retractable landing gear pulls up out
of view, giving the camera an unobstructed 360 degree view of the world
below.
An advanced flight controller makes the Inspire 1 stable, safe and easy to fly
indoors or out. The brand new Vision Positioning System (VPS) gives it the
power to hover in position at low altitudes even without GPS. Like all DJI
flight controllers, it is also able to return home if remote controller signal
is lost or if the low battery warning is triggered.
The Inspire 1 boasts a maximum flight speed 20m/s and a maximum flight time
of 18.5 minutes using one fully charged 4500mAh Intelligent Flight
Battery.
| 1. Gimbal and Camera | 9. Intelligent Flight Battery |
|---|---|
| 2. Camera Micro-SD Card Slot | 10. Power Button |
| 3. Vision Positioning System | 11. Battery Level Indicators |
| 4. Transformation Mechanism | 12. Aircraft Status Indicator |
| 5. Front LEDs | 13. Aircraft Micro-USB Port |
| 6. Motors | 14. Camera Micro-USB Port |
| 7. Propellers | 15. Gimbal Lock |
| 8. Rear LEDs |
- The maximum flight speed and maximum run time (hovering state) were tested in a lab environment, at zero-level elevation and in windless conditions, and should be taken as reference only.
Remote Controller
The maximum transmission distance of the Inspire 1 remote controller is 5km*.
The remote controller also allows you to control the landing gear or activate
Return to Home with a tap. Other buttons allow instant photo capture, video
recording, picture review and gimbal control.
A DJI Lightbridge-based HD video downlink is built-in, letting you see what
your camera sees on your mobile device in real time HD. The app also allows
you to change camera settings and activate Master/Slave mode so that one
person can fly while other controls the gimbal independently. The master and
slave controllers communicate using a 5.8Ghz wireless signal, and have a
communication range with each other of up to 50 meters. The controller’s
Lipoid battery has a maximum run time of approximately four hours and can be
charged by plugging directly into the controller.
- Power Button
- Transformation Switch
- Return to Home (RTH) Button
- Control Sticks
- Status LED
- Battery Level LEDs
- Power Port
- Mobile Device Holder
- Antennas
- Handle Bar
- Gimbal Dial
- Camera Settings Dial
- Video Recording Button
- Flight Mode Switch
- Shutter Button
- Playback Button
- Mini-HDMI Port
- Micro-USB Port
- CAN-Bus Port
- USB Port
- Back Buttons (Reserved)
- Please note that the max transmission distance were tested in a lab environment. This statistic is for reference only, as conditions in your area may vary.
Fly Safe
DJI encourages you to enjoy flying in a safe, responsible and smart way.
DO NOT FLY near or above people, near trees, power lines or buildings.
DO NOT FLY in rain, snow, fog, and wind speeds exceeding 22 mph or 10 m/s.
DO MONITOR YOUR ALTITUDE
and fly under 400 feet (120 meters).
DO MAINTAIN LINE OF SIGHT
and avoid flying behind buildings or obstacles that block your view.
It is important to understand basic flight guidelines, for the safety of both you and those around you. Refer to the Safety Guidelines and Disclaimer for more information.
No Fly Zones
More information at: http://flysafe.dji.com/no-fly
- Be very careful when flying 14,700 feet (4,500 meters) or more above sea level as the battery and aircraft performance may be reduced.
- The Inspire 1’s compass and GPS will not work in Polar Regions. The aircraft will auto switch to ATTI Mode and use the VPS for positioning.
● Calibrating the Compass:
Only calibrate the compass when the DJI GO app or the status indicator prompt
you to do so. Observe the following rules when calibrating your compass:
- DO NOT calibrate your compass where there is a chance of strong magnetic interference, such as magnetite, parking structures, and steel reinforcements underground.
- DO NOT carry ferromagnetic materials with you during calibration such as cellular phones.
- The DJI GO app will prompt you to resolve the compass issue if the compass is affected by strong interference after calibration is complete. Follow the prompted instructions to resolve the compass issue.
● P Mode:
In this mode, the Inspire 1 has a strong GPS signal and can use the VPS
allowing it to hover accurately in position indoors and out. If outdoors, this
mode also means that a
Home Point has been locked so that it can Return to Home if the control signal
is lost.
If you are not in this mode, toggle the Flight Mode Switch to P position to
enable it.
The Flight Mode Switch is locked in P mode by default.
Refer to the User Manual on how to unlock the switch.
There are three states in P mode.
P-GPS: GPS works best when outdoors in a wide open area, and your Inspire 1
uses GPS to hover in place when the GPS signal is strong. P-OPTI: If GPS
is not available, the aircraft can use the VPS to hover accurately.
P-ATTI: Neither GPS or VPS available, aircraft is using only its barometer
for positioning, so only altitude is controlled. Note that the VPS may not
work properly when the Inspire 1 is flying over water, over surfaces without a
clear pattern, or in a low light environment.
● Return to Home:
When the GPS signal is strong, the aircraft will be able to record a Home
Point and return to the Home Point when needed. The GPS location is recorded
when the GPS signal icon in the DJI GO app is either yellow or green.
The aircraft will return to the Home Point automatically in the following
cases (all require a strong GPS signal).
Smart RTH: When you press the RTH button on the remote controller or in the
App. Low Battery RTH: The DJI GO app notifies users to take action when the
battery level falls to a specified threshold.
Failsafe RTH: When the remote controller signal is lost.
- While returning home, its altitude can be adjusted by the user to avoid obstructions. Tall buildings may affect the remote controller signal. The Failsafe Return to Home procedure will be triggered if the signal is lost. Be sure fly higher than any nearby buildings to avoid crashing.
Appendix
● Aircraft (Model: T600)
| Weight | 2845 g (Battery and Propellers Included, Zen muse X3 Excluded) |
|---|---|
| Weight | 3060 g (Battery, Propellers and Zen muse X3 Included) |
| Maximum Weight of Payload | 3500 g |
| Max Tilt Angle | 35° |
| Max Ascent Speed | 5 m/s |
| Max Descent Speed | 4 m/s |
| Max Speed | 20 m/s (ATTI mode, no wind) |
| Max Altitude Above Sea Level | 14,700 feet (4,500 meters) |
| Max Flight Time | Approximately 18.5 minutes |
| Operating Temperature Range | 14° to 104° F (-10° to 40° C) |
● Gimbal (Model: ZENMUSE X3)
| Angular Vibration Range | ±0.03° |
|---|---|
| Controllable Range | Pitch: -90° to +30° Pan: ±320° |
| Max Controllable Speed | Pitch: 120°/s Pan: 180°/s |
● Vision Positioning System
| Velocity Range | <8 m/s @Altitude 6.56 feet (2 m) |
|---|---|
| Altitude Range | 0.16 feet – 16.4 feet (5 cm-500 cm) |
| Operating Range | <9.84 feet (<300 cm) |
| Operating Environment | Surface with clear pattern and adequate lighting (>15 |
Lux )
● Camera (Name/Model: X3/FC350)
Sensor| Sony Exmore R CMOS (Type 1/2.33), Effective pixels: 12.4M (total
pixels: 12.76M)
---|---
Lens| FOV (Field Of View) 94° 20 mm (35 mm format equivalent) f/2.8
ISO Range| 100-3200 (video) 100-1600 (photo)
Electronic Shutter Speed| 8 s-1/8000 s
Image Max Size| 4000×3000
Still Photography Modes| Single shoot; Burst shooting: 3/5/7 frames
Auto Exposure Bracketing (AEB): 3/5 bracketed frames at 0.7EV Bias; Time-lapse
Video Recording Modes| UHD: 4K (4096×2160) 24/25p, 4K (3840×2160) 24/25/30p,
FHD: 1920×1080 24/25/30/48/50/60p,
HD: 1280×720 24/25/30/48/50/60p
Max Bitrate Of Video Storage Supported File Systems| 60 Mbps
Supported File Systems| FAT32 (≤ 32 GB), exeats (> 32 GB)
Photo Formats| JPEG, DNG
Video Formats| MP4/MOV (MPEG-4 AVC/H.264)
Supported SD Card Types Operating Temperature Range| Micro SD, Max capacity:
64GB. Class 10 or UHS-1 rating required
Operating Temperature Range| 32° to 104° F (0° to 40° C)
● Remote Controller (Name: C1)
Operating Frequency| 922.7 MHz-927.7 MHz (Japan only) 5.725 GHz-5.825 GHz
2.400 GHz-2.483 GHz
---|---
Transmitting Distance| Up to 5 km or 3.1 miles (unobstructed, free of
interference) when FCC compliant
Up to 3.5 km or 2.1 miles (unobstructed, free of interference) when CE
compliant
Video Output Port| USB, Mini-HDMI
Operating Temperature Range Battery| 14° to 104° F (-10° to 40° C)
Battery| 6000 mAh LiPo 2S
● Charger (Model: A14-100P1A)
| Voltage | 26.3 V |
|---|---|
| Rated Power | 100 W |
● Intelligent Flight Battery (Model: TB47, Standard)
| Capacity | 4500 mAh |
|---|---|
| Voltage | 22.2 V |
| Battery Type | LiPo 6S High voltage battery |
| Energy | 99.9 Wh |
| Net Weight | 570 g |
| Operating Tempe | 14° to 104° F (-10° to 40° C) |
| Max Charging Power | 180 W |
● Intelligent Flight Battery (Model: TB48, Optional)
| Capacity | 5700 mAh |
|---|---|
| Voltage | 22.8 V |
| Battery Type | LiPo 6S High voltage battery |
| Energy | 129.96 Wh |
| Net Weight | 670 g |
| Operating Tempe | 14° to 104° F (-10° to 40° C) |
| Max Charging Power | 180 W |
※ This Quick Start Guide is subject to change without prior notice.
Using INSPIRE 1
-
Download the DJI GO App
Search ‘DJI GO’ on the App Store or Google Play and download the app to your mobile device.http://m.dji.net/djigo -
Watch the Tutorial Videos
Watch the tutorial videos at www.dji.com or in the DJI GO app.http://www.dji.com/product/inspire-1/video
● For the best user experience, please use mobile devices with iOS 8.0 (or higher) and Android 4.1.2 (or higher).
● Read the Inspire 1 User Manual in the DJI GO app or official DJI website for more details. -
Check Battery Levels
● Press once to check the battery level.
● Press once, again and hold to turn on/off.
-
Charge the Batteries
● The Intelligent Flight Battery must be fully charged before using it for the first time.
● Only use the official DJI Inspire 1 charger for your Intelligent Flight Battery and remote controller. Power off the Intelligent Flight Battery before charging.
● When charging is complete, the LED lights on the Intelligent Flight Battery and remote controller will turn off.
Preparing the Remote Controller
Unfold the mobile device holder and the antennas.
Dual Remote Controllers
You will need to link the Master and Slave remote controllers.
On the Master RC, launch the DJI GO app and enter Camera View. Tap on the top
of your screen to bring up the RC Settings. Set the RC Status as ‘Master’, and
then enter the desired connection password.
Similarly on the Slave RC, set the RC Status to ‘Slave’. Then tap Search for
Master RC and connect to the Master RC with your preset password.
● DO NOT use other 2.4 GHz devices at the same time to avoid signal
interference.
● DO NOT operate more than 3 aircrafts within in the same area (size
equivalent to a soccer field) to prevent transmission interference.
Prepare the Aircraft
Insert the battery
Power on the remote controller and the aircraft
Toggle the transformation switch up and down at least four times
Transform the aircraft to Landing Mode
Mount the Gimbal and Camera
● Be sure to remove the gimbal before transforming the aircraft to Travel
Mode.
● Always power off the aircraft before mounting or removing the gimbal.
Preparing for Takeoff
Toggle the Flight Mode Switch to the safest P-Mode.
Connect your mobile device.
Power on the remote controller and aircraft.
Launch the DJI GO app and enter Camera View.
Pair the propellers and motors with arrows of the same color (red or white).
Rotate the propeller lock until the arrows are aligned and you hear a click.
Attach the propeller onto the motor.
Again, rotate the propeller lock until you hear a click.
● Ensure the propellers are mounted securely and correctly.
Controls
The stick mode is set to Mode 2 by default (left hand throttle). The left
stick controls the aircraft’s elevation and heading.
The right stick controls the aircraft’s forward, backward and lateral
movements. The gimbal dial controls camera tilt.
● You can change the stick mode in the DJI GO app.
Flight
Safe to Fly (GPS)
In the DJI GO App:
Before taking off, ensure the Aircraft Status Bar in the DJI GO app indicates
‘Safe to Fly (GPS)’.
Auto Takeoff
The aircraft will take off and hover at an altitude of 4 feet (1.2 meters).
Return-to-Home
Brings the aircraft back to the Home Point. Tap again to stop the procedure.
Auto Landing
The aircraft will land vertically and stop its motors.
- The aircraft will not avoid obstacles while it is returning to the Home Point, and an appropriate RTH altitude must be set before takeoff. You should also use the control sticks to guide the aircraft.
Refer to the Safety Guidelines and Disclaimer for more details.
Manual Takeoff
Return-to-Home (RC)
Same as the RTH button in the DJI GO app.
Brings the aircraft back to the Home Point.
Press and hold to initiate the RTH procedure.
Press again to cancel.
Manual Landing
Ensure the landing gear is lowered before lending
****If you want to lower the landing gear but the switch is already in the ‘down’ position, toggle the switch up and down again.
Left stick down (slowly) until you touch the ground.
Hold a few seconds to stop the motors.
- Rotating propellers can be dangerous. DO NOT start the motors in narrow spaces or when there are people nearby.
- Never perform the Combination Stick Command in mid-flight, or else the aircraft will crash.
- Always keep your hands on the remote controller so long as the motor is still spinning.
- After landing, power off the aircraft before turning off the remote controller.
- Take off from a flat surface in a wide open space, with the rear of the aircraft facing towards you.
Appendix
Aircraft Status Indicator
slowly . . . Safe to fly (GPS working).
. . . No GPS but VPS working.
slowly . . . P-ATTI or ATTI mode.
quickly ….. Not connected to remote controller.
slowly . . . Low battery level warning.
quickly ….. Critical low battery level warning.
solid —— Critical error.
. . . compass calibration required.
Remote Controller Status Indicator
RC normal but not connected to aircraft.
RC normal and connected to aircraft.
RC Slave Mode and not connected to aircraft.
RC Slave Mode and connected to aircraft.
( B… ) Low battery warning / RC error.
( B—B—… ) RC idle for 5 minutes.
Downloading Your Videos
- Compressed video and photo files are automatically stored on your mobile device while you are recording. You can view them in the Library section of the DJI GO app.
- For the best quality, download the original HD files through the app or using an SD card reader.
※ This content is subject to change without prior notice.
www.dji.com/product/inspire-1
Learn more information from:
INSPIRE™ and DJI | INSPIRE™ are trademarks of DJI.
Designed by DJI. Printed in China.
Copyright © 2016 DJI All Rights Reserved.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>