SOUNDMAX SM-CCR3055F USB-SD Media Player Instruction Manual

: June 6, 2024
: SOUNDMAX

Table of Contents

Important safeguards
Accessories
Installation/Connection
Connection diagram
Control elements
General operations
Radio operations
USB/SD operations
Troubleshooting guide
Specification
Documents / Resources
- Read User Manual Online (PDF format)
- Download This Manual (PDF format)

SOUNDMAX SM-CCR3055F USB-SD Media Player Instruction Manual

Dear customer!
Thank you for purchasing our product. For safety, it is strongly recommended to read this manual carefully before connecting, operating and/or adjusting the product and keep the manual for reference in the future.

Important safeguards

Read carefully through this manual to familiarize yourself with this high-quality sound system.
The beginning of operation is the moment of the unit installation. Before use the device in winter it is recommended to heat up the passenger compartment during 20 seconds or to the operation temperature.
Use the unit with the temperature that goes beyond the operation temperature greatly decreases the operation resource of the screen and other components of device and can result an outage.
Disconnect the vehicle’s negative battery terminal while mounting and connecting the unit.
When replacing the fuse, be sure to use one with an identical amperage rating. Using a fuse with a higher amperage rating may cause serious damage to the unit.
Make sure that pins or other foreign objects do not get inside the unit; they may cause malfunctions, or create safety hazards such as electrical shock.
Do not use the unit in places where it can be exposed to water, moisture and dust.
Do not open covers and do not repair yourself. Consult the dealer or an experienced technician for help.
Make sure you disconnect the power supply and aerial if you will not be using the system for a long period or during a thunderstorm.
Make sure you disconnect the power supply if the system appears to be working incorrectly, is making an unusual sound, has a strange smell, has smoke emitting from it or liquids have got inside it. Have a qualified technician check the system.
The unit is designed for negative terminal of the battery, which is connected to the vehicle metal. Please confirm it before installation.
Do not allow the speaker wires to be shorted together when the unit is switched on. Otherwise it may overload or burn out the power amplifier.

Accessories

Receiver 1 pc
Mounting parts:
Hexagon nut 1 pc
Mounting sleeve 1 pc
Release keys 2 pcs
Metal bar 1 pc
Plain washer 1 pc
Spring washer 1 pc
Self-tapping screw 1 pc
Screw 4 pc
Connector 1 pc
Consumer information 1 pc
Warranty card 1 pc
Instruction manual 1 pc

Installation/Connection

General notes

Choose the mounting location where the unit will not interfere with the normal driving function of the driver.
Before finally installing the unit, connect the wiring and make sure that the unit works properly.
Consult with your nearest dealer if installation requires the drilling of holes or other modifications of the vehicle.
Install the unit where it does not get in the driver’s way and cannot injure the passenger if there is a sudden stop, like an emergency stop.
Avoid installing the unit where it would be subject to high temperature, such as from direct sunlight, or from hot air, from the heater, or where it would be subject to dust, dirt or excessive vibration.

DIN FRONT-MOUNT

DIN FRONT-MOUNT

Car dashboard
Sleeve
Bolt
Nut
Spring washer
Screw
Metal strap
Flat washer
Install the sleeve into the dashboard; ensure it is installed with the correct side and there are no obstacles (wires, dashboard elements, etc) for the unit installation.
After installing the sleeve into the dashboard, bend tabs fitting to the size of the dashboard to fix the sleeve in place.
Use the metal strap to fix the rear side of the unit. Determine a place for fixing and install the strap as shown in the picture. You can bend the strap to the needed angle with your hands.
Make the necessary wire connections. Ensure the connections are correct.
Install the unit into the sleeve until the side locks are fixed.

Dismantling the unit

Dismantling the unit

1. Make sure the ignition is turned off, then disconnect the cable from the vehicle battery’s negative (-) terminal.

Remove the metal strap attached the back of the unit (if attached).
Insert both of the supplied keys into the slots at the middle left and right sides of the unit, then pull the unit out of the dashboard.

Connection diagram

Note: Auto antenna wire is intended for power supply of the antenna and for remote control of an additional amplifier.

Control elements

Front panel
Control elements

button
MOD button
button
button
CLK button
BND button
VOLUME knob/BASS/TREBLE/BALANCE/FADER/LOUD/EQ button
RESET button (hole)
1 PLAY/PAUSE
2/RPT buttons
3/RDM
4 button s
LCD
5/-10
6/+10 buttons
SD card slot
AUX input
USB port

General operations

Turning the unit on/off
Press the button to turn the unit on. Press the button again to turn the unit off.

Reset the unit
When first using the device or after replacing the car battery, you must reset the unit. Press the RESET button (hole) with a pointed object (such as a ballpoint pen) to set the unit to its initial state.
When some errors occur, you can also press the RESET button to return to factory settings, but note that it will erase clock setting and some memorized functions.

Mode selection
Press the MOD button repeatedly to select between Radio, AUX, MP3 modes. Operation modes are indicated on the display. MP3 mode is not available unless a memory card or a USB device is connected.

Volume control
Adjust the volume by rotating the VOLUME knob.

Clock
Press the CLK button to display time. Press and hold this button to set the clock, rotate the volume knob for adjustment.

Audio parameter setting
Press the VOL knob repeatedly to select a parameter: BAS (bass) => TRE (treble) => BAL (balance) => FAD (fader). Press and hold the button to select LOUD (loudness), press and hold again to select EQ (equalizer). Rotate the knob to adjust each mode.

Bass/Treble: from -7 to +7;
Balance: -10 (left) to +10 (right);
Fader: from -10 (rear) to +10 (front).
Loudness: see “Loudness” paragraph below
EQ: select POP/CLASS/ROCK or OFF equalizer mode.
When equalizer is in any mode except OFF, bass and treble are not adjustable.

Loudness
Activating this feature will enhance bass and treble frequencies when listening to music at low volumes.

AUX input
AUX-in jack is intended for connecting an external audio equipment to amplify the sound. If connection is made correctly, the audio signal from the external source will be transmitted through the acoustics of the head unit. This enables to adjust the volume and quality of the sounding. For example, you can connect an MP3- player to listen to tracks using the car acoustic system.

Radio operations

Band select
In Radio mode press the BAND button to select a radio band: FM1 => FM2 => FM3.

Manual/automatic tuning

Press shortly button. The radio will automatically search for the next frequency with a strong and clear signal.
Press and hold button, the unit will go to manual tuning mode. Press buttons repeatedly to adjust the needed frequency manually.

Storing and recalling stations

Press and hold the BAND button for several seconds to automatically find and store 6 strongest stations in the current band corresponding with the preset number button.
Press preset buttons (1-6) to select saved channels. If you want to save a new station in a preset position, select the corresponding station number with preset buttons. Then tune to the needed frequency as described in “Manual/automatic tuning“ above and press and hold a preset button. The new frequency will be saved in the selected position.

USB/SD operations

SD card slot
Carefully insert the SD card into the card slot on the front panel. Unit starts playback automatically. To disconnect the memory card, press it until a click, and then carefully pull it out from the slot.

USB port
Carefully connect a USB driver to the USB jack on the front panel. Unit starts playback automatically.

USB/SD notes
USB format supports 2.0. Capacity: up to 16 GB. SD cards capacity: up to 16 GB. Supported file systems are FAT/FAT32.

Note: Because of the great variety of products with SD-card slots and their sometimes quite manufacturer-specific functions the producer can neither guarantee that all devices will be recognized nor that all operating options that are possible in theory will actually work. Before disconnecting a storage, switch the unit to another mode.

Next/Previous track
Press or buttons to choose next or previous track. Press and hold this button to choose forward playback or backward playback; release the button to return to normal playback.

Play/Pause
Press PLAY/PAUSE button to pause the playback, press one more time to resume normal playback.

Repeat playback
When RPT button is pressed, playback of the selected track will be continually repeated and RPT indicator will be displayed until the track repeat mode is canceled by pressing 3 RPT button again.

Random
When RDM button is pressed, each track on the storage is played in random instead of normal order. RDM indicator will be displayed. To cancel Random mode, press 4 RDM button again.

Skipping tracks
Press -10 button to go back 10 tracks. Press +10 button to go forward 10 tracks

Troubleshooting guide

Below is a table describing simple measures that can help you eliminate most problems likely to emerge when this unit is in use. If below measures do not help, turn to a service center or to the nearest dealer.

Symptom	Cause	Solution
No power	Wiring is connected incorrectly.	Make correct wiring connection.
The car ignition is not on.	If the power supply is properly connected to the

car accessory, switch the ignition on.
The fuse is blown.| Replace the fuse.
No sound| Volume is in minimum.| Adjust volume to the desired level.
Wiring is not properly connected.| Check wiring connection.
The radio does not work| The antenna cable is not connected.| Insert the antenna cable properly.
The radio station automatic tuning does not work| The signals are too weak.| Select stations manually.

Cleaning the unit body

Wipe with a soft cloth. If the cabinet is very dampen (not dropping wet) the cloth with a weak solution of soapy water, and then wipe clean.