ELKO RFGB-40 Wireless Light Dimmer Instruction Manual
- June 4, 2024
- ELKO
Table of Contents
WIRELESS LIGHT DIMMER
(LUXURY VERSION)
Combination of iNELS wall-mounted wireless controller and dimmer for regulation of all types of dimmable bulbs and light sources.
Content
| Glass touch controller – 4 buttons, SHARP RFGB-40/W, RFGB-40/B
---|---
| Glass touch controller – 4 buttons, ROUND RFGB-240/W, RFGB-240/B
| Universal dimmer, 1-channel, RFDEL-71B-SL
EAN 8595188183031 (Glass touch controller – 4 buttons, SHARP – white + 1 x
Universal dimmer)
EAN 8595188183079 (Glass touch controller – 4 buttons, SHARP – white + 2 x
Universal dimmer)
EAN 8595188183055 (Glass touch controller – 4 buttons, SHARP – white + 1 x
Universal dimmer)
EAN 8595188183093 (Glass touch controller – 4 buttons, SHARP – white + 2x
Universal dimmer)
EAN 8595188183024 (Glass touch controller – 4 buttons, SHARP – black + 1 x
Universal dimmer)
EAN 8595188183062 (Glass touch controller – 4 buttons, SHARP – black + 2 x
Universal dimmer)
EAN 8595188183048 (Glass touch controller – 4 buttons, SHARP – black + 1 x
Universal dimmer)
EAN 8595188183086 (Glass touch controller – 4 buttons, SHARP – black + 2x
Universal dimmer)
The individual elements in the iNELS set are paired and their functions are preset. iNELS Wireless light dimmer enables dimming of different types of lights or controlling electrical appliances
The settings of the wall controllers can be changed – detailed manual on the next pages.
Glass touch controller – 4 buttons, SHARP/ROUND, RFGB-40/RFGB-240
Detailed manual
|
---|---
RFGB-40| RFGB-240
RFGB-40/B – glass touch controller, SHARP – black, 4-buttons
RFGB-40/W – glass touch controller, SHARP – white, 4-buttons
RFGB-240/B – glass touch controller, ROUND – black, 4-buttons
RFGB-240/W – glass touch controller, ROUND – white, 4-buttons
Characteristics
- The wireless control – is used to control, lights, gates, garage doors, shitters, etc.
- The thickness is only 8 mm.
- 4 capacitive buttons allow you to control 2/4 components.
- Fast installation on any surface – the rear base allows screwing to the walls, gluing with double-sided tape or just laying on the table
Replacement of a battery in 3 steps
Assembly
Adhesive
In
the installation box or on the wall
Technical parameters
RFGB-40/RFGB-240
Power voltage: | 2x 3 V battery CR 2032 |
---|---|
Battery life: | about 2 years depending on the frequency of use |
Transmission indication | Red LED |
A number of capacitive buttons: | 4 |
Communication Protocol: | RFIO2 |
Frequency: | 868.5 MHz |
Signal transmission method: | one-way addressed message |
Range: | in the open up to 200 m |
Material: | Glass |
Other data
Operating Temperature:| -10 … +50 °C (14 122 °F)
Working Position| any
Mounting:| adhesive, screw
Protection| IP20
Pollution degree:| 2
Dimension:| SHARP 94 x 94 x 8 mm (3.7″ x 3.7″x 0.3″) / ROUND 100 x 100 x 8 mm
(3.9″ x 3.9″ x 03″)
Weight:| SHARP 107 g/ ROUND 108 g
Related standards:| EN 60669, EN 300 220, EN 301 489
Universal dimmer, 1-channel RFDEL-71B-SL
Detailed manual
RFDEL-71B-SL
Characteristics
- The universal built-in dimmer is used to regulate light sources.
- They can be combined with detectors, controllers, iNELS RF Control or system components.
- 7 light functions – smooth increase or decrease with time setting 2s-30 min. + additional function SWITCH OFF
- Thanks to setting the min. brightness you will eliminate fl ashing of the LED and ESL light sources
- The universal dimmer may be controlled by up to 25 channels (1 channel represents 1 button).
- The connection of the existing button on the control input “S“ enables the combination of wireless control with classic (wired) control.
- The programming button on the controller is also used for manual control of the output.
- For components labeled as iNELS RF Control 2 (RFIO 2 ), it is possible to set the repeater function via the RFAF/USB service device.
- Range up to 200 m (in open space), if the signal is insufficient between the controller and unit, use the signal repeater RFRP-20 or protocol component RFIO 2
that support this feature.
Installation option
Technical parameters
RFDEL-71B-SL
Supply voltage: | 230 V AC / 50 Hz |
---|---|
Apparent power: | 5 VA |
Dissipated power: | 0.5 W |
Supply voltage tolerance: | +10/ -15 % |
Connection: | 4 – wire, with NEUTRAL |
Dimmed load: R. L. C. LED. ESL
Output:
Contactless:| 2 x MOSFET
Load capacity:| 300 W •
Control:
RF command from the transmitter:| 868.5 MHz
Range in open space: up to 200 m
Manual control:| button PROG (ON/OFF), external button
Other data:
Operating temperature: -15 … + 45 °C
Storage temperature:| -30 +70°C
Operating position:| any
Protection:| IP40 under normal conditions
Overvoltage category:| III.
Contamination degree:| 2
Connection:| screwless terminals
Connecting conductor:| 0.2-1.5 mm2
Dimensions:| 43 x 44 x 22 mm
Weight:| 30 g
Related standards:| EN 60730. EN 63044. EN 300 220. EN 301 489
Compatibility
The device can be combined with all system components, controls and devices of iNELS RF Control and iNELS RF Control 2 . The detector can be assigned an iNELS RF ontrol 2 (RFIO 2 ) communication protocol.
Connection
Radiofrequency signal penetration through various construction materials
Range up to 200 m in open space, if the signal is insufficient between the
controller and unit, use the signal repeater RFRP-20 or protocol component
RFIO 2
that supports this feature.
| | | |
---|---|---|---|---
60 – 90 %| 80 – 95 %| 20 – 60 %| 0 – 10 %| 80- 90 %
brick walls| wooden structures with plasterboards| reinforced concrete| metal
partitions| common glass
Warning
The instruction manual is designated for mounting and also for the usage of
the device. It is always a part of its packing. Installation and a connection
can be carried out only by a person with adequate professional quality cation
with an understanding of this instruction manual and functions of the device,
and while observing all valid regulations. The trouble-free function of the
device also depends on transportation, storing, and handling. In case you
notice any sign of damage, deformation, malfunction or missing part, do not
install this device and return it to its seller. It is necessary to treat this
product and its parts as electronic waste after its lifetime is terminated.
Before starting the installation, make sure that all wires, connected parts or
terminals are de-energized. While mounting and servicing observe safety
regulations, norms, directives, and professional, and export regulations
forworking with electrical devices. Do not touch parts of the device that are
energized – a life threat. Due to the transmissivity of RF signal, observe the
correct location of RF components in a building where the installation is
taking place. RF Control is designated only for mounting in interiors. Devices
are not designated for installation in exteriors and humid spaces. They must
not be installed into metal switchboards and into plastic switchboards with
metal door – transmissivity of RF signal is then impossible. control is not
recommended for pulleys etc. – radiofrequency signal can be shielded by an
obstruction, interfered, a battery of the transceiver can getfl at etc. and
thus disable the remote control.
Notes
Designed & Manufactured by:
ELKO EP, s.r.o. Palackého 493, 769 01 Holešov, Všetuly,
Czech republic,www.elkoep.com, Hotline: +420 800
100 67
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>