ELKO 10AX Smart Relay Puck User Guide

**ELKO 10AX Smart Relay Puck User Guide

**

Commissioning instructions for the ELKO Smart system, devices and app.

Legal Information

The information provided in this document contains general descriptions, technical characteristics and/or recommendations related to products/solutions.

This document is not intended as a substitute for a detailed study or operational and site-specific development or schematic plan. It is not to be used for determining suitability or reliability of the products/solutions for specific user applications. It is the duty of any such user to perform or have any professional expert of its choice (integrator, specifier or the like) perform the appropriate and comprehensive risk analysis, evaluation and testing of the products/solutions with respect to the relevant specific application or use thereof.

The ELKO brand and any trademarks of ELKO AS and its subsidiaries referred to in this document are the property of ELKO AS or its subsidiaries. All other brands may be trademarks of their respective owner.

This document and its content are protected under applicable copyright laws and provided for informative use only. No part of this document may be reproduced or transmitted in any form or by any means (electronic, mechanical, photocopying, recording, or otherwise), for any purpose, without the prior written permission of ELKO.

ELKO does not grant any right or license for commercial use of the document or its content, except for a non-exclusive and personal license to consult it on an “as is” basis.

ELKO reserves the right to make changes or updates with respect to or in the content of this document or the format thereof, at any time without notice.

To the extent permitted by applicable law, no responsibility or liability is assumed by ELKO and its subsidiaries for any errors or omissions in the informational content of this document, as well as any non-intended use or misuse of the content thereof.

Safety information

Important information

Read these instructions carefully and look at the equipment to become familiar with the device before trying to install, operate, service, or maintain it. The following special messages may appear throughout this manual or on the equipment to warn of potential hazards or to call attention to information that clarifies or simplifies a procedure.
The addition of either symbol to a “Danger” or “Warning” safety label indicates that an electrical hazard exists which will result in personal injury if the instructions are not followed.
This is the safety alert symbol. It is used to alert you to potential personal injury hazards. Obey all safety messages that accompany this symbol to avoid possible injury or death.

DANGER

DANGER : indicates a hazardous situation which, if not avoided, will result in death or serious injury. Failure to follow these instructions will result in death or serious injury.
WARNING
WARNING indicates a hazardous situation which, if not avoided, could result in death or serious injury
CAUTION
CAUTION : indicates a hazardous situation which, if not avoided, could result in minor or moderate injury.
NOTICE
NOTICE : is used to address practices not related to physical injury.

SmartRelay Puck 10AX

EKO07144

For your safety

**DANGER**

HAZARD OF ELECTRIC SHOCK, EXPLOSION, OR ARC FLASH
Safe electrical installation must be carried out only by skilled professionals. Skilled professionals must prove profound knowledge in the following areas:

• Connecting to installation networks.
• Connecting several electrical devices.
• Laying electric cables.
• Safety standards, local wiring rules and regulations.

Failure to follow these instructions will result in death or serious injury.

DANGER
HAZARD OF ELECTRIC SHOCK

• Make sure that the terminal connection area does not come in contact with the metallic parts of any device installed in the same location.
• Do not short the outputs to neutral.
• The switch contact and live conductor connection must be separated from one another by a 240 VAC basic insulation. Failure to follow these instructions will result in death or serious injury.

WARNING
HAZARD OF ELECTRIC SHOCK

• Observe the regulations for working on live parts.
• Only actuate the device buttons using insulated auxiliary equipment that meets the requirements of EN 60900. Failure to follow these instructions can result in death, serious injury, or equipment damage.

About the device

The SmartRelay Puck 10AX (hereinafter referred to as Puck / Micro Module Switch) combines the advantages of smart switch functionality with ordinary mechanical push-button switches. It transforms a conventional switch into a connected device that can be controlled from the switch or through the ELKO Smart app. It can switch ohmic, inductive or capacitive loads.
NOTE: Do not control any devices that depend on a permanent power supply. Additional features:

• Remote controlled with maximum of 10 mechanical push-buttons.
• Setting a time schedule

Installing the device

Refer to the installation instruction supplied with this product. See SmartRelay Puck 10AX

Testing the device

WARNING

HAZARD OF ELECTRIC SHOCK

• Observe the regulations for working on live parts.
• Only actuate the device buttons using insulated auxiliary equipment that meets the requirements of EN 60900.

Failure to follow these instructions can result in death, serious injury, or equipment damage.

Short press the test button once, the connected device turns on/off.

Pairing the device with Smart Hub

Using the ELKO Smart app, first pair your device with the ELKO SmartHub to access and control the device. You can either add the device manually or do an auto-scan to pair it.

Pairing device manually

To pair the device manually:

1. On Home page, tap +.

2. Tap , select ELKO SmartHUB on the slide-up menu and tap Done.

3. Select any one of the options to add device (A):

   • Add Device with Install Code
   • Add Device without Install Code
     
     TIP: It is recommended to add the device with install code.

4. . To pair the device with an install code, tap Add Device with Install Code to display the slide-up menu. Select any one of the options (B):

   • Scan Install Code: you can scan the device for the install code.
   • Enter Install Code Manually: you can manually enter the install code from the device.
     TIP: you can find the install code on the rear side of the device. After scanning or entering the install code, proceed to Step 7.

5. To pair the device without install code, tap Add Device without Install Code.

6. Select any one of the options to add the device:

   • Short press the S/R (setup/reset) button 3 times (<0,5 s) on the Puck with a screwdriver.
   • Short press the push button 3 times.
     
     The LED blinks orange.
     NOTE: If the puck is located behind the push button, the status LED is not visible.

7. In the app, select Confirm LED is flashing orange and tap Start Configuration (C).
   
   After a few seconds, a solid green LED indicates that the device has been successfully paired to the ELKO Smart HUB.
   
   

8. Tap Done when the pairing is successful..

Pairing device with auto scan

Pairing the device with auto scan automatically discovers the device when the corresponding device is powered on.

1. On the Home page, tap +.

2. Tap Auto scan > Confirm.

3. Enable permissions to Access location and Wi-Fi for scanning device and tap Start scanning.
   NOTE: If you have multiple hubs, do Step 4 or proceed to Step 5.

4. Tap Select hub and select the ELKO SmartHub from the slide-up menu.

5. Short press the setup/reset button 3 times (< 0,5 s) and wait for a few seconds until the device search is complete.
   The LED blinks orange.
   TIP: If you want to pair multiple devices at once, perform step 5 on each device and wait for a few seconds for them to be detected.

6. Tap Next (A) and select Micromodule Switch.
   

7. Once the device is added successfully, tap Done.

Configuring the device

Changing the device icon

You can change the device icon using the ELKO Smart app.

1. On the Home page, select the device for which you wish to change the icon.
2. At the top-right corner of the screen, tap .
3. Tap edit next to the device name.
4. Tap Icon to view the menu.
5. In the slide-up menu, select any one of the following (A) to change the device icon:
   • Take photo – allows you to take a photo with your device camera.
   • Select from Icon Library: allows you to select an icon from the app library.
   • Select from Album: allows you to select a photo from the mobile gallery.
     

Renaming the device

You can rename the device using the ELKO Smart app.

1. On the Home page, select the device for which you wish to rename.

2. At the top-right corner of the screen, tap .

3. Tap edit next to the device name.
   

4. Tap Name, enter the new name (A) and then tap Save.

Changing the device location

You can change the device location using the ELKO Smart app.

1. On the Home page, select the device for which you wish to change the location.
2. At the top-right corner of the screen, tap .
3. Tap edit next to the device name.
4. Tap Location.
5. Select the desired location from the list (A) and then tap Save.
   

Removing the device

Using the ELKO Smart app, you can remove a device from the device list.
To remove the device:

1. On the Home page, tap All devices > Micromodule Switch.

2. Tap to display more details.

3. Tap Remove and Factory Reset Device (A).
   
   TIP: On the Home page, tap and hold the Micromodule Switch to remove the device.
   NOTE:

   • Removing the device will reset the puck. After reset the LED turns orange indicating that the puck is ready to pair with another network.
   • If there is a problem while pairing or resetting the puck, refer to Resetting the device manually, page 12.

Resetting the device

You can reset the device to factory default manually.

1. Short press ( <0,5 s) the Setup/Reset button 3 times and then long press the Setup/Reset button once for 10 s to reset the Puck to factory default mode. or
2. After 10 s, LED starts blinking red then release the operation button.
   NOTE: All configuration data, user data, and network data are deleted.
   The LED stops blinking upon successful reset of the device.
   The puck restarts and blinks green for a few seconds.
   

Using the device

Manual operation
When the puck is connected to a mechanical push button, the connected devices can be controlled manually by short pressing the push button.
NOTE: When the puck is installed inside the wall box, the status LED is not visible while using the puck.

Turning the light switch on/off using app

Using the ELKO Smart app, you can turn on/off the light switch remotely.

1. On the Home page, tap All devices.
2. In Micro module Switch tap on to turn on/off the light switch.
   

Setting up a schedule

The device can be fully controlled by schedule. Once the schedule is set, the device operates at a given time.

1. In the device control panel, tap Schedule > Add Schedule to add a schedule.

2. In Add Schedule menu, set the time (A).
   NOTE: The Schedule works according to the time zone where the device is located.

3. Tap Repeat (B) to select the days you want to set the schedule.

4. Tap Note (C), enter the note and tap Confirm.

5. Tap the toggle switch (D) to turn on the Notification for the schedule. The app will send a notification that the scheduled task is executed at the scheduled time.

6. Tap Switch (E) and select any option, On or Off.
   

7. Tap Save.

Creating a moment

Moment allows you to group multiple actions that are usually done together. Using the ELKO Smart app, you can create moments based on your needs.

1. On the Home page, tap .

2. Go to Moment > + to create a moment.

3. Tap Edit name (A), enter the name of the moment and tap Save.
   TIP: You can choose the cover image that represents your moment by tapping .
   

4. In the Action section, tap Add task (B) to open the slide-up menu.

5. In the Add task menu, you can do either or all of the following actions (C):

   • Run the device: select the devices that you want in a moment.
   • Select Automation: select the automation that you want to enable or disable.
   • Delay: set the delay time.
     NOTE: You can add one or more actions using .
     

6. Tap Run the device > Micromodule Switch.

7. Tap on Switch and select either On / Off / Reverse Switch and tap Save.

8. Tap Next and once the actions are set, tap Save.

Editing a moment

To edit a moment:

1. On the Moment tab, locate the moment you want to edit and tap .
2. On the Edit page, you can tap each item (such as dimmer, shutter, delay,
   temperature, etc.) to change the settings.

TIP:

• You can add one or more actions using .
• To delete an existing action, slide the each item towards left and tap Delete.

Deleting a moment

To delete a moment:

1. On the Moment tab, locate the moment that you want to delete and then tap .
2. Tap Delete and than tap Ok.
   NOTE: After deleting a moment, the device action can no longer be triggered.

Creating an automation

Automation allows you to group multiple actions that are usually done together, triggered automatically or at scheduled times. Using the ELKO Smart app, you can create automations based on your needs.

1. On the Home page, tap the .

2. Go to Automation > + to create an automation.

3. Tap Edit name (A), enter the name of the automation and tap Save.
   TIP: You can choose the cover image that represents your automation by tapping .
   

4. Tap Any condition is met to select any one of the condition type (B):

   • All conditions are met: the automation is triggered when all the conditions are met.
   • Any condition is met: the automation is triggered when at least one condition is met.
     

5. Tap Add Condition to open the slide-up menu.

6. In the Add Condition menu, you can do either or all of the following options
   (C):

   • When weather changes: select the various weather settings.
   • Schedule: set the time and day.
   • When device status changes: select the device and it’s function.
     NOTE: You can add one or more conditions using .
     

7. Tap When device status changes > Switch and select either functions:

   • On: turn on the switch.
   • Off: turn off the switch.
   • Reverse Switch: toggle the last state of the switch.
     

8. Tap Add task to open the slide-up menu.

9. In the Add task menu, you can do either or all of the following options (D):

   • Run the device: select the devices that you want to trigger.
   • Moment or Automation: select the moment which you want to trigger or select the automation that you want to enable or disable.
   • Send notification: turn on notification for the automation.
   • Delay: set the delay time.
     NOTE: You can add one or more actions using .
     

10. Tap on Effective period to set the time range for the automation. You can select any one of the following (E):

    • All-day – 24 hours
    • Daytime – From sunrise to sunset
    • Night – From sunset to sunrise
    • Custom – User defined time period
      

11. Once all the actions and conditions are set, tap Save.
    Once the automation is saved, it is visible on the Automation tab. You can tap the toggle switch on the automation to enable it.

Example of an automation

This demonstration shows you how to create an automation to switch on the light when the door is opened.

1. Go to Automation > + to create an automation.

2. Tap Edit name , enter the name of the automation and tap Save.
   TIP: You can choose the cover image that represents your automation by tapping .

3. Tap Add Condition > When device status changes > Window/Door Sensor.

4. Tap Window/Door Sensor > Open.

5. Tap Add task > Run the device and select Micro Module Light Switch.

6. Tap Switch > On (A) and tap Save.

7. Tap Next.
   
   

8. In the Automation Settings page, tap Save.
   
   Once the automation is saved, it is visible on the Automation tab. You can tap the toggle switch on the automation to enable it.

Editing an automation

To edit an automation:

1. On the Automation tab, locate the automation you want to edit and tap .
2. On the Edit page, you can tap each item (such as dimmer, shutter, delay, temperature, etc.) to change the settings.

TIP:

• You can add one or more actions using .
• To delete an existing condition or action, slide each item towards left and tap Delete

Deleting an automation

To delete an automation:

1. On the Automation tab, locate the automation that you want to delete and then tap .
2. Tap Delete and tap Ok .
   NOTE: After deleting an automation, the device action can no longer be triggered.

LED indication

Pairing the device

once per second. **

**| Pairing mode is active for 30 seconds. When pairing is completed, LED glows green for a few seconds before turning Off.

Resetting the device

Short press the setup/reset button or push button 3 times and hold it down once for > 10 s.| LED blinks red once per second. ****| The device is in reset mode. The device then restarts and LED turns orange indicating that the device is ready for pairing. ****

Troubleshooting

Resetting the device manually, page 12.

Technical data

Nominal power rating for load type

| Incandescent lamp| 2200 W
| Halogen lamp| 2000 W
| Iron core transformer| 500 VA
| Motor| 1000 VA
| Electronic step-down converter| 1050 VA
| Capacitive load| 10 A, 140 µF
| Fluorescent lamp| 100 W
| LED| 200 W
| Boiler| 2000 W
         | Room heater| 1500 W
Nominal voltage| AC 220-240 V, 50/60 Hz
---|---
Nominal current| 10 AX
Switching channel| 1, dry contact
Standby| Max. 0.3 W
Operating Temperature| 0 ºC to 35 ºC
Neutral conductor| Required
Connecting terminals| Max. 2 x 2.5 mm2, solid or stranded types
Extension connection| Max. 10 mechanical push buttons
Length of all cable sections| Max. 50 m for 3-wire NYM cable
Fuse protection| 16 A circuit breaker
Operating frequency| 2405 – 2480 MHz
Max. radio-frequency power transmitted| <10 mW
IP rating| IP20
Product dimensions (H x W x D)| 43 x 43 x 22 mm
Communication protocol| Zigbee 3.0 certified

Trademarks

This guide makes reference to system and brand names that are trademarks of their relevant owners.

• Zigbee® is a registered trademark of the Connectivity Standards Alliance.
• Apple® and App Store® are brand names or registered trademarks of Apple Inc.
• Google Play™ Store and Android™ are brand names or registered trademarks of Google Inc.
• Wi-Fi® is a registered trademark of Wi-Fi Alliance®.

Other brands and registered trademarks are the property of their respective owners.

ELKO AS
Sandstuveien 68, 0680 Oslo
Pb 6598 Etterstad, 0607 Oslo
Norway
+47 67 79 39 00
support@elko.no
www.elko.no
As standards, specifications, and design change from time to time, please ask for confirmation of the information given in this publication.
© 2023 – ELKO AS. All rights reserved.
DUG_SmartRelay Puck_ELKO-00

References

• elko.no - Hjem

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>