BOYA BY-M1LV-D 2.4GHz Wireless Microphone System User Manual

BOYA BY-M1LV-D 2.4GHz Wireless Microphone System

General Introduction

Thanks for choosing BOYA!
The BOYA BY-M1LV is an incredibly lightweight, ultracompact and easy-to-use 2.4Ghz wireless microphone system for mobile devices, delivering detailed, exceptional-quality sound.

The system series is comprised of two different receivers. The BY-M1LV-D-RX receiver features an MFi Certified Lightning output, designed for Apple iOS devices.

The BY-M1LV-U-RX receiver features a USB-C output, allowing it to work with Android phones, tablets, and other devices with a USB-C port. The BY-M1LV-TX clip-on transmitter has a high-quality built-in mic. It is small and light enough to clip to shirts and clothing. With gain control, headphone volume control, and mute function, you are in total control of your sound. The BOYA BY-M1LV system provides a great solution for live streaming, Content creation, mobile journalism, and more.

Available Kits

Model/In the box

• BY-M1LV-D
  • 1x BY-M1LV-D-RX
  • 1x BY-M1LV-TX
• BY-M1LV-U
  • 1x BY-M1LV-U-RX
  • 1xBY-M1LV-TX

Product Structure

BY-M1LV-TX: Clip-on Transmitter with Built-in Microphone.

Status indicator

• Mode Indicator
• Unpaired Flashing blue light
• Pairing Blue and red lights flash alternately
• Paired Successfully Slow flashing blue light
• Mute ON Solid green light
• Microphone Monitor ON (Supports Direct& Playback Monitoring) Slow flashing green light
• Microphone Monitor OFF (Only Supports Playback Monitoring) Green light off
• Low Battery Flashing red light
• Charging Solid red light
• Fully Charged Light off

Built-in microphone
3.5mm headphone jack

• Connect headphones for audio monitoring.

USB-C charging port

Mode button

• Function Operation
• Gain adjustment Short press the button to adjust mic gain. There are 3 steps for gain setting)
• Enable the microphone monitor function
  • Double-click the button to enter microphone monitor mode. Then, press the +/-button to adjust the headphone volume. Double-click the button again to exit microphone monitor mode.

Power/Mute button

• Function Operation
• Power ON/OFF Press and hold for 3 seconds
• Mute ON/OFF Short press
• Pairing Double-click

Volume control (+-button)

• Press the +/- button to adjust the headphone volume.

Belt clip

Voice Prompt

• Power ON “Power ON”
• Power OFF “Power OFF”
• Connected “Bluetooth Connected”
• Disconnected “Bluetooth Disconnected”
• Class One (Gain Setting) “Class One”
• Class Two (Gain Setting) “Class Two”
• Class Three (Gain Setting) “Class Three”
• Microphone Monitor Function Enabled “Microphone Monitor ON”
• Microphone Monitor Function Disabled “Microphone Monitor OFF
• Low Battery “Battery Low”
• Mute OFF “Microphone ON”
• Mute ON “Microphone OFF”

BY-M1LV-D-RX: Compact Receiver with Lightning Connector

1. Lightning Connector
   • It can be connected to an iOS lightning device.
2. Pairing Indicator
   • Mode Indicator
   • Unpaired Flashing blue light
   • Pairing Quick flashing blue light
   • Paired Successfully Slow flashing blue light
3. Pair Pinhole

BY-M1LV-U-RX: Compact Receiver with USB-C Connector

1. USB-C Connector
   • It can be connected to an Android smartphone, tablet or other USB-C devices.
2. Pairing Indicator
   • Mode Indicator
   • Unpaired Flashing blue light
   • Pairing Quick flashing blue light
   • Paired Successfully Slow flashing blue light
3. Pair Pinhole

Operation Guide

1. Press and hold the power button for 3 seconds to turn on the transmitter.

2. Plug the BY-M1LV-D-RX into an iOS device or the BY-M1LV-U-RX into a USB-C device.

3. Transmitter and receiver pairing
   Before leaving the factory, the system is pre-paired. Therefore, the connection
   will be established once they are powered on. If they are disconnected,
   please follow the steps below:

4. Double-click the power button of the transmitter. The indicator flashes blue and red alternately.

5. When the transmitter indicator flashes blue and red alternately, insert the supplied pairing pin into the small pinhole on the receiver. The indicator of the receiver flashes blue rapidly.

6. The transmitter and receiver will be paired within 10 seconds. Indicators of both will flash blue slowly.

7. You are ready to record.

Note:
Due to the 2.4GHz wireless frequency, the signal can be easily attenuated. Please try to avoid obstacles, such as walls and buildings, and avoid close proximity to devices with 2.4GHz signals, such as high-power wiń antennas, smartphones with a win in use, radios, etc.

Connection Example

Specifications

BY-M1LV-TX

• Transmission Type 2.4GHz
• Modulation GFSK
• Operating Range Up to 328′ (100m) (without obstacles)
• RF Output Power 3.16mW
• Microphone Polar Pattern Built-in Microphone: Omnidirectional
• Frequency Response 50Hz-8.5KHz
• SNR 70dB
• Maximum SPL Built-in Microphone: 110dB SPL
• Sensitivity Built-in Microphone:-39dB+2dB (OdB=1V/Pa@1kHz)
• Power Requirement Built-in Li-ion Battery or USB-C DC 5V
• Antenna PIFA Antenna
• Battery Life Approx. 6 hours
• Audio Output 3.5mm Jack
• Weight Approx. 18g
• Dimensions 40×38.2x14mm
• Operating Temperature 0’C to 50°C
• Storage Temperature -20°C to 55°C

BY-M1LV-D-RX

• Transmission Type 2.4GHz
• Modulation GFSK
• Operating Range Up to 328′ (100m) (without obstacles)
• RF Output Power 3.16mW
• Audio Output MFi Certified Lightning Connector
• Power Requirement Supplied by ioS Devices
• Antenna PIFA Antenna
• Noise Cancellation Yes
• Weight Approx. T0g
• Dimensions 23×38.2x14mm
• Operating Temperature 0’C to 50°c
• Storage Temperature -20°C to 55°C

BY-M1LV-U-RX

• Transmission Type 2.4GHz
• Modulation GFSK
• Operating Range Up to 328′ (100m) (without obstacles)
• RF Output Power 3.16mW
• Audio Output USB-C Connector
• Power Requirements Supplied by USB-C Devices
• Antenna PIFA Antenna
• Noise Reduction Yes
• Weight Approx. 10g
• Dimensions 23×38.2x14mm
• Operating Temperature O’C to 50°C
• Storage Temperature -20’C to 55’C

Packing List

BY-M1LV-D (BY-M1LV-TX+ BY-M1LV-D-RX)

• 1xBY-M1LV-TX Transmitter
• 1x BY-M1LV-D-RX Receiver
• 1x USB-C Charging Cable
• 1x Fur Windshield
• 1x Pairing Pin

BY-M1LV-U (BY-M1LV-TX+ BY-M1LV-U-RX)

• 1x BY-M1LV-TX Transmitter
• 1x BY-M1LV-U-RX Receiver
• 1xUSB-C Charging Cable
• 1 x Fur Windshield
• 1x Pairing Pin

User Manual

Documents / Resources

| BOYA BY-M1LV-D 2.4GHz Wireless Microphone System [pdf] User Manual
BY-M1LV-D, BY0M1LV-U, BY-M1LV-D 2.4GHz Wireless Microphone System, BY-M1LV-D, 2.4GHz Wireless Microphone System, Wireless M, Wireless Microphone Systemicrophone System
---|---

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>